Hostname: page-component-78c5997874-g7gxr Total loading time: 0 Render date: 2024-11-02T13:08:26.906Z Has data issue: false hasContentIssue false
  • English
  • Français

Diffusion barrier development for fiber-reinforced Ni3Al composites

Published online by Cambridge University Press:  31 January 2011

P.C. Brennan ,
W.H. Kao ,
H.A. Katzman  and
J-M. Yang
P.C. Brennan
Affiliation:
Materials Sciences Laboratory, The Aerospace Corporation, El Segundo, California 90245
W.H. Kao
Affiliation:
Materials Sciences Laboratory, The Aerospace Corporation, El Segundo, California 90245
H.A. Katzman
Affiliation:
Materials Sciences Laboratory, The Aerospace Corporation, El Segundo, California 90245
J-M. Yang
Affiliation:
Department of Materials Science and Engineering, University of California, Los Angeles, California 90024
Get access

Abstract

An alumina (Al2O3) diffusion barrier coating to inhibit the interfacial reactions between boron-carbide-coated boron (B4C/B) fibers and a nickel-aluminide (Ni3Al) (IC-221) matrix was investigated. The alumina diffusion barrier was deposited on the B4C/B fibers using chemical vapor deposition. Also, Saphikon single-crystal Al2O3 fibers were used to demonstrate the compatibility between Al2O3 and Ni3Al. The detailed microstructures and chemical compositions of the fibers, coating, and matrix before and after various thermal exposures were analyzed using scanning electron microscopy, energy dispersive x-ray analysis, and ion microprobe mass analysis. The interfacial reaction products present after 6 h at 980 °C were characterized, and Ni was found to be the dominant diffusion species. The alumina diffusion barrier shows promise for effectively inhibiting the deleterious reactions between B4C/B fibers and the Ni3Al matrix. The uncoated B4C/B fibers were consumed by the matrix after fabrication alone, whereas the Al2O3 coated fibers demonstrated resistance to the matrix for 25 h at 880 °C and 6 h at 980 °C. The Saphikon fiber-reinforced Ni3Al composites demonstrated excellent compatibility after 50 h at 1000 °C. Zirconium (Zr)-rich precipitates on the order of 2 μm in diameter formed at the fiber interface after this exposure, but no gross reaction was indicated between the fiber and the matrix.

Type
Articles
Information
Journal of Materials Research , Volume 6 , Issue 2 , February 1991 , pp. 355 - 360
Copyright
Copyright © Materials Research Society 1991

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1Yang, J-M., Kao, W. H., and Liu, C. T., Mater. Sci. & Engr. A107, 81 (1989).CrossRefGoogle Scholar
2Stoloff, N. S., in High-Temperature Ordered Intermetallic Alloys, edited by Koch, C. C., Liu, C. T., and Stoloff, N. S. (Materials Research Society, Pittsburgh, PA, 1984), p. 3.Google Scholar
3Liu, C. T. and White, C. L., in High-Temperature Ordered Inter-metallic Alloys, edited by Koch, C. C., Liu, C. T., and Stoloff, N. S. (Materials Research Society, Pittsburgh, PA, 1984), p. 365.Google Scholar
4Nieh, T. C., Stephens, J. J., Wadsworth, J., and Liu, C. T., in Proc. Int. Conf. of Composite Interfaces, edited by Ishida, H. (Elsevier Science Publishing Company, June 1988).Google Scholar
5Povirk, G. L., Horton, J. A., McKamey, C. G., Tiegs, T. N., and Nutt, S. R., J. Mater. Sci. 23 (1988).CrossRefGoogle Scholar
6Liu, C. T., in MiCon 86: Optimization of Processing, Properties, and Service Performance Through Microstructural Control, edited by Bramfitt, B. L., Benn, R. C., Brikman, C. R., and Voorf, G. F. Vander, ASTM STP 979 (1988), p. 222.CrossRefGoogle Scholar
7Brennan, P. C., Development of a Diffusion Barrier for Fiber-Reinforced IC-221 Nickel Aluminide, Master of Science Thesis, UCLA (1988).Google Scholar
8 Private communication with Liu, C. T., ORNL.Google Scholar
9Fuchs, G. E. and Kao, W. H., “Development of Intermetallic Matrix Composites for Elevated Temperature Service,” in Proc. 1988 Int. P/M Conf., American Powder Metallurgy Institute, Orlando, FL (1988).Google Scholar
10Miller, M. K. and Horton, J. A., Scripta Metall. 20, 1125 (1986).CrossRefGoogle Scholar
11Schneidmiller, R. F. and White, J. E., “A Compatibility Study of SiC and B Fibers in Be, Fe, Co, and Ni Matrices,” Advanced Fibrous Reinforced Composites, Vol. 10, SAMPE Paper E-53 (1966).Google Scholar