Crossref Citations
This article has been cited by the following publications. This list is generated based on data provided by Crossref.
Malzbender, J.
Wakui, T.
and
Steinbrech, R. W.
2006.
Curvature of Planar Solid Oxide Fuel Cells during Sealing and Cooling of Stacks.
Fuel Cells,
Vol. 6,
Issue. 2,
p.
123.
Chen, J.
and
Bull, S.J.
2006.
A critical examination of the relationship between plastic deformation zone size and Young's modulus to hardness ratio in indentation testing.
Journal of Materials Research,
Vol. 21,
Issue. 10,
p.
2617.
Malzbender, Jürgen
2006.
Reply to the comments on “Comment on the determination of mechanical properties from the energy dissipated during indentation” by J. Malzbender [J. Mater. Res. 20, 1090 (2005)].
Journal of Materials Research,
Vol. 21,
Issue. 1,
p.
306.
Alkorta, J.
Martínez–Esnaola, J.M.
Sevillano, J. Gil
and
Malzbender, Jürgen
2006.
Comments on “Comment on the determination of mechanical properties from the energy dissipated during indentation” by J. Malzbender [J. Mater. Res. 20, 1090 (2005)].
Journal of Materials Research,
Vol. 21,
Issue. 1,
p.
302.
Chen, J.
and
Bull, S. J.
2008.
Investigation of the relationship between work done during indentation and the hardness and Young's modulus obtained by indentation testing.
International Journal of Materials Research,
Vol. 99,
Issue. 8,
p.
852.
Sahin, Osman
Uzun, Orhan
Sopicka-Lizer, Malgorzata
Gocmez, Hasan
and
Kölemen, Uğur
2008.
Analysis of load-penetration depth data using Oliver–Pharr and Cheng–Cheng methods of SiAlON–ZrO2ceramics.
Journal of Physics D: Applied Physics,
Vol. 41,
Issue. 3,
p.
035305.
Chudoba, T
and
Jennett, N M
2008.
Higher accuracy analysis of instrumented indentation data obtained with pointed indenters.
Journal of Physics D: Applied Physics,
Vol. 41,
Issue. 21,
p.
215407.
Chen, J.
and
Bull, S.J.
2009.
Relation between the ratio of elastic work to the total work of indentation and the ratio of hardness to Young's modulus for a perfect conical tip.
Journal of Materials Research,
Vol. 24,
Issue. 3,
p.
590.
Kusano, E.
and
Kikuchi, N.
2011.
Interface stress induced hardness enhancement and superelasticity in polytetrafluoroethylene/metal multilayer thin films.
Thin Solid Films,
Vol. 520,
Issue. 1,
p.
404.
Jha, Kaushal K.
Suksawang, Nakin
Lahiri, Debrupa
and
Agarwal, Arvind
2013.
Evaluating initial unloading stiffness from elastic work-of-indentation measured in a nanoindentation experiment.
Journal of Materials Research,
Vol. 28,
Issue. 6,
p.
789.
Menčík, Jaroslav
2014.
Energy Aspects of Concentrated Contact and Instrumented Indentation.
Key Engineering Materials,
Vol. 606,
Issue. ,
p.
61.
Jha, Kaushal K.
Suksawang, Nakin
Lahiri, Debrupa
and
Agarwal, Arvind
2015.
A novel energy-based method to evaluate indentation modulus and hardness of cementitious materials from nanoindentation load–displacement data.
Materials and Structures,
Vol. 48,
Issue. 9,
p.
2915.
Yetna N'Jock, M.
Roudet, F.
Idriss, M.
Bartier, O.
and
Chicot, D.
2016.
Work-of-indentation coupled to contact stiffness for calculating elastic modulus by instrumented indentation.
Mechanics of Materials,
Vol. 94,
Issue. ,
p.
170.
Chicot, D.
N’Jock, M. Yetna
Roudet, F.
Decoopman, X.
Staia, M.H.
and
Puchi-Cabrera, E.S.
2016.
Some improvements for determining the hardness of homogeneous materials from the work-of-indentation.
International Journal of Mechanical Sciences,
Vol. 105,
Issue. ,
p.
279.
Hervas, I.
Montagne, A.
Van Gorp, A.
Bentoumi, M.
Thuault, A.
and
Iost, A.
2016.
Fracture toughness of glasses and hydroxyapatite: A comparative study of 7 methods by using Vickers indenter.
Ceramics International,
Vol. 42,
Issue. 11,
p.
12740.
Gao, Chenghui
Yao, Ligang
and
Liu, Ming
2018.
Berkovich nanoindentation of borosilicate K9 glass.
Optical Engineering,
Vol. 57,
Issue. 03,
p.
1.
Peruzzo, M.
Serafini, F.L.
Ordoñez, M.F.C.
Souza, R.M.
and
Farias, M.C.M.
2019.
Reciprocating sliding wear of the sintered 316L stainless steel with boron additions.
Wear,
Vol. 422-423,
Issue. ,
p.
108.
Schiavi, Alessandro
Origlia, Claudio
Germak, Alessandro
Prato, Andrea
and
Genta, Gianfranco
2021.
Indentation Modulus, Indentation Work and Creep of Metals and Alloys at the Macro-Scale Level: Experimental Insights into the Use of a Primary Vickers Hardness Standard Machine.
Materials,
Vol. 14,
Issue. 11,
p.
2912.
Liu, Ming
Cong, Zhibo
Fu, Haiying
and
Li, Pengyuan
2022.
Relationships in instrumented indentation by Berkovich indenter.
Journal of Materials Research,
Vol. 37,
Issue. 23,
p.
4084.
Beake, Ben D.
2022.
The influence of the H/E ratio on wear resistance of coating systems – Insights from small-scale testing.
Surface and Coatings Technology,
Vol. 442,
Issue. ,
p.
128272.