Hostname: page-component-cd9895bd7-8ctnn Total loading time: 0 Render date: 2024-12-27T13:31:36.607Z Has data issue: false hasContentIssue false
  • English
  • Français

Anisotropy and microstructural evolutions of X70 pipeline steel during tensile deformation

Published online by Cambridge University Press:  26 June 2018

Qiuzhi Gao ,
Cheng Lu ,
Huijun Li ,
Jintao Li ,
Jian Han  and
Liang Chen
Qiuzhi Gao*
Affiliation:
School of Resources and Materials, Northeastern University at Qinhuangdao, Qinhuangdao, Hebei 066004, China; School of Mechanical, Materials and Mechatronic Engineering, University of Wollongong, Wollongong, NSW 2522, Australia
Cheng Lu
Affiliation:
School of Mechanical, Materials and Mechatronic Engineering, University of Wollongong, Wollongong, NSW 2522, Australia
Huijun Li*
Affiliation:
School of Mechanical, Materials and Mechatronic Engineering, University of Wollongong, Wollongong, NSW 2522, Australia
Jintao Li
Affiliation:
School of Mechanical, Materials and Mechatronic Engineering, University of Wollongong, Wollongong, NSW 2522, Australia
Jian Han
Affiliation:
School of Mechanical, Materials and Mechatronic Engineering, University of Wollongong, Wollongong, NSW 2522, Australia
Liang Chen
Affiliation:
School of Mechanical, Materials and Mechatronic Engineering, University of Wollongong, Wollongong, NSW 2522, Australia
*
a)Address all correspondence to these authors. e-mail: [email protected]
b)e-mail: [email protected]
Get access

Abstract

Tensile properties of different directions of X70 pipeline steel plate were tested, and microstructural evolutions of different zones along the transverse direction (TD) were also investigated using electron backscatter diffraction. The highest strength values (yield strength and ultimate strength) appear at TD, and the diagonal direction shows the largest uniform elongation. The elongations of the polygonal ferrite and quasi polygonal ferrite grains increase with the decrease in the distance to the fracture zone. The ratio between high-angle grain boundaries and low-angle grain boundaries in the as-received steel is about 7/3 and starts to decrease from the fillet zone to the fracture zone. The refinement of grains occurs adjacent to the fracture section with the formation of subgrains. With the increase in tensile strain, the intensities of cube and γ-fiber textures increase sharply, and the reinforcement of the (111)$\left[ {\bar{1}\bar{1}2} \right]$ component was obviously larger than the (111)$\left[ {1\bar{2}1} \right]$ component in the γ-fiber texture during tensile deformation.

Keywords

X70 pipeline steeltensile propertiestexturemicrostructure
Type
Article
Information
Journal of Materials Research , Volume 33 , Issue 20 , 29 October 2018 , pp. 3512 - 3520
Copyright
Copyright © Materials Research Society 2018 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

El-Danaf, E., Baig, M., Almajid, A., Alshalfan, W., Al-Mojil, M., and Al-Shahrani, S.: Mechanical, microstructure and texture characterization of API X65 steel. Mater. Des. 47, 529 (2013).CrossRefGoogle Scholar
Han, J., Lu, C., Wu, B., Li, J., Li, H., Lu, Y., and Gao, Q.: Innovative analysis of Luders band behaviour in X80 pipeline steel. Mater. Sci. Eng., A 683, 123 (2017).CrossRefGoogle Scholar
Liang, G., Peng, X., San Juan, E., and Cheng, Y.F.: Strain aging of X100 steel in service and the enhanced susceptibility of pipelines to stress corrosion cracking. J. Mater. Eng. Perform. 22, 3778 (2013).CrossRefGoogle Scholar
Su, L., Li, H., Lu, C., Li, J., Fletcher, L., Simpson, I., Barbaro, F., Zheng, L., Bai, M., Shen, J., and Qu, X.: Transverse and z-direction CVN impact tests of X65 line pipe steels of two centerline segregation ratings. Metall. Mater. Trans. A 47, 3919 (2016).CrossRefGoogle Scholar
Masoumi, M., Herculano, L.F.G., and de Abreu, H.F.G.: Study of texture and microstructure evaluation of steel API 5L X70 under various thermomechanical cycles. Mater. Sci. Eng., A 639, 550 (2015).CrossRefGoogle Scholar
Zhu, Z., Han, J., and Li, H.: Influence of heat input on microstructure and toughness properties in simulated CGHAZ of X80 steel manufactured using high-temperature processing. Metall. Mater. Trans. A 46, 5467 (2015).CrossRefGoogle Scholar
Gao, Q., Wang, Y., Gong, M., Qu, F., and Lin, X.: Non-isothermal austenitic transformation kinetics in Fe–10Cr–1Co alloy. Appl. Phys. A 122, 1 (2016).CrossRefGoogle Scholar
Shukla, R., Ghosh, S.K., Chakrabarti, D., and Chatterjee, S.: Microstructure, texture, property relationship in thermo-mechanically processed ultra-low carbon microalloyed steel for pipeline application. Mater. Sci. Eng., A 587, 201 (2013).CrossRefGoogle Scholar
Zhao, M-C., Hanamura, T., Qiu, H., Nagai, K., Shan, Y-Y., and Yang, K.: Difference in the role of non-quench aging on mechanical properties between acicular ferrite and ferrite-pearlite pipeline steels. ISIJ Int. 45, 116 (2005).CrossRefGoogle Scholar
Shanmugam, S., Ramisetti, N.K., Misra, R.D.K., Hartmann, J., and Jansto, S.G.: Microstructure and high strength–toughness combination of a new 700 MPa Nb-microalloyed pipeline steel. Mater. Sci. Eng., A 478, 26 (2008).CrossRefGoogle Scholar
Xu, L.Y. and Cheng, Y.F.: An experimental investigation of corrosion of X100 pipeline steel under uniaxial elastic stress in a near-neutral pH solution. Corros. Sci. 59, 103 (2012).CrossRefGoogle Scholar
Joo, M.S., Suh, D.W., and Bhadeshia, H.K.D.H.: Mechanical anisotropy in steels for pipelines. ISIJ Int. 53, 1305 (2013).CrossRefGoogle Scholar
Sung, H.K., Lee, D.H., Lee, S., Kim, H.S., Ro, Y., Lee, C.S., Hwang, B., and Shin, S.Y.: Correlation between microstructures and tensile properties of strain-based API X60 pipeline steels. Metall. Mater. Trans. A 47, 2726 (2016).CrossRefGoogle Scholar
Pogozhev, A.V., Tskitishvili, E.O., Matrosov, Y.I., Klyukvin, M.B., Matrosov, M.Y., and Konovalov, G.N.: Experience of using accelerated cooling in production of steel X70 plate for the Central Asia—China gas pipeline. Metallurg 57, 215 (2013).CrossRefGoogle Scholar
Gourgues, A.F., Flower, H., and Lindley, T.: Electron backscattering diffraction study of acicular ferrite, bainite, and martensite steel microstructures. Mater. Sci. Technol. 16, 26 (2000).CrossRefGoogle Scholar
Masoumi, M., Herculano, L.F.G., Almeida, A.A., Béreš, M., and Abreu, H.F.G.: Texture study across thickness of API X70 steel after hot deformation and different posttreatments. JOM 68, 401 (2015).CrossRefGoogle Scholar
Joo, M.S., Suh, D.W., Bae, J.H., and Bhadeshia, H.K.D.H.: Role of delamination and crystallography on anisotropy of Charpy toughness in API-X80 steel. Mater. Sci. Eng., A 546, 314 (2012).CrossRefGoogle Scholar
Yoshida, F., Hamasaki, H., and Uemori, T.: Modeling of anisotropic hardening of sheet metals including description of the Bauschinger effect. Int. J. Plast. 75, 170 (2015).CrossRefGoogle Scholar
Sun, H.B., Yoshida, F., Ohmori, M., and Ma, X.: Effect of strain rate on Lüders band propagating velocity and Lüders strain for annealed mild steel under uniaxial tension. Mater. Lett. 57, 4535 (2003).CrossRefGoogle Scholar
Kim, Y.M., Kim, S.K., Lim, Y.J., and Kim, N.J.: Effect of microstructure on the yield ratio and low temperature toughness of linepipe steels. ISIJ Int. 42, 1571 (2002).CrossRefGoogle Scholar
Lake, J.S.H.: Control of discontinuous yielding by temper rolling. J. Mech. Work. Technol. 12, 35 (1985).CrossRefGoogle Scholar
Hutanu, R., Clapham, L., and Rogge, R.B.: Intergranular strain and texture in steel Luders bands. Acta Mater. 53, 3517 (2005).CrossRefGoogle Scholar
Yang, X.L., Xu, Y.B., Tan, X.D., and Wu, D.: Relationships among crystallographic texture, fracture behavior and Charpy impact toughness in API X100 pipeline steel. Mater. Sci. Eng., A 641, 96 (2015).CrossRefGoogle Scholar
Diaz-Fuentes, M., Iza-Mendia, A., and Gutierrez, I.: Analysis of different acicular ferrite microstructures in low-carbon steels by electron backscattered diffraction. Study of their toughness behavior. Metall. Mater. Trans. A 34, 2505 (2003).CrossRefGoogle Scholar
Nafisi, S., Arafin, M.A., Collins, L., and Szpunar, J.: Texture and mechanical properties of API X100 steel manufactured under various thermomechanical cycles. Mater. Sci. Eng., A 531, 2 (2012).CrossRefGoogle Scholar
Humphreys, F.J.: Characterisation of fine-scale microstructures by electron backscatter diffraction (EBSD). Scr. Metall. 51, 771 (2004).CrossRefGoogle Scholar
Mingard, K.P., Roebuck, B., Bennett, E.G., Gee, M.G., Nordenstrom, H., Sweetman, G., and Chan, P.: Comparison of EBSD and conventional methods of grain size measurement of hardmetals. Int. J. Refract. Met. Hard Mater. 27, 213 (2009).CrossRefGoogle Scholar
Humphreys, F.: Review grain and subgrain characterisation by electron backscatter diffraction. J. Mater. Sci. 36, 3833 (2001).CrossRefGoogle Scholar
Canadinc, D., Efstathiou, C., and Sehitoglu, H.: On the negative strain rate sensitivity of Hadfield steel. Scr. Metall. 59, 1103 (2008).CrossRefGoogle Scholar
Cooreman, S., Lecompte, D., Sol, H., Vantomme, J., and Debruyne, D.: Identification of mechanical material behavior through inverse modeling and DIC. Exp. Mech. 48, 421 (2008).CrossRefGoogle Scholar
Hamada, A.S., Haggag, F.M., and Porter, D.A.: Non-destructive determination of the yield strength and flow properties of high-manganese twinning-induced plasticity steel. Mater. Sci. Eng., A 558, 766 (2012).CrossRefGoogle Scholar
Supplementary material: File

Gao et al. supplementary material

Figure S1

Download Gao et al. supplementary material(File)
File 606.7 KB