Hostname: page-component-586b7cd67f-r5fsc Total loading time: 0 Render date: 2024-11-28T11:09:58.105Z Has data issue: false hasContentIssue false
  • English
  • Français

Scratch test induced shear banding in high power laser remelted metallic glass layers

Published online by Cambridge University Press:  03 March 2011

D.T.A. Matthews ,
V. Ocelík  and
J.Th.M. de Hosson
D.T.A. Matthews
Affiliation:
Department of Applied Physics and Netherlands Institute for Metals Research, University of Groningen, Groningen 9474 AG, The Netherlands
V. Ocelík
Affiliation:
Department of Applied Physics and Netherlands Institute for Metals Research, University of Groningen, Groningen 9474 AG, The Netherlands
J.Th.M. de Hosson*
Affiliation:
Department of Applied Physics and Netherlands Institute for Metals Research, University of Groningen, Groningen 9474 AG, The Netherlands
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Laser remelted surface layers of a Cu-based metallic glass forming alloy have been produced with fully amorphous depths up to 350 μm for single track widths of around 1.3 mm and have been checked by transmission of synchrotron radiation. They have been subjected to indentation hardness and scratch testing, and the development of shear bands in both situations has been addressed. During the cross-sectional hardness indentation tests, Vickers values of over 735 HV2 have been found through the depth of the treated layer, and the scratch testing has revealed extremely low friction coefficient values (<0.02 at 10 N in single-pass and 0.02 at 18 N multi-pass regimes against a diamond stylus). The shear band formation has been related to both scratch test speed (strain rate) and load (contact stress) by methods such as atomic force microscopy measurements and subsequent surface roughness characterization by a height–height correlation function.

Keywords

AmorphousLaserTribology
Type
Articles
Information
Journal of Materials Research , Volume 22 , Issue 2 , September 2006 , pp. 460 - 470
Copyright
Copyright © Materials Research Society 2007

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Schuh, C.A. and Nieh, T.G.: A nanoindentation study of serrated flow in bulk metallic glasses. Acta Mater. 51, 87 (2003).CrossRefGoogle Scholar
2Jana, S., Ramamurty, U., Chattopadhyay, K., and Kawamura, Y.: Subsurface deformation during Vickers indentation of bulk metallic glasses. Mater. Sci. Eng., A 375–377, 1191 (2004).CrossRefGoogle Scholar
3Sergueeva, A.V., Mara, N.A., Kuntz, J.D., Laernia, E.J., and Mukherjee, A.K.: Shear band formation and ductility in bulk metallic glass. Philos. Mag. 85, 2671 (2005).CrossRefGoogle Scholar
4Yang, B., Riester, L., and Nieh, T.G.: Strain hardening and recovery in a bulk metallic glass under nanoindentation. Scripta Mater. 54, 1277 (2006).CrossRefGoogle Scholar
5Matthews, D.T.A., Ocelik, V., and de Hosson, J.Th.M.: Metallic glass layers produced by high power lasers, in Bulk Metallic Glass. Special Issue, Mater. Sci. Eng. A (in press).Google Scholar
6Park, E.S., Lim, H.K., Kim, W.T., and Kim, D.H.: The effect of Sn addition on the glass-forming ability of Cu–Ti–Zr–Ni–Si metallic glass alloys. J. Non-Cryst. Solids 298, 15 (2002).CrossRefGoogle Scholar
7Bull, S.J. and Rickerby, D.S.: Multi-pass scratch testing as a model for abrasive wear. Thin Solid Films 181, 545 (1989).CrossRefGoogle Scholar
8Persson, B.N.J.: Sliding friction. Surf. Sci. Rep. 33, 83 (1999).CrossRefGoogle Scholar
9Bennett, S., Matthews, A., Perry, A.J., Valli, J., Bull, S.J., and Sproul, W.D.: Multi-pass scratch testing at sub-critical loads. Tribologia. Finnish J. Tribol. 13, 16 (1994).Google Scholar
10Pilloz, M., Pelletier, J.M., and Vannes, A.B.: Residual stresses induced by laser coatings: Phenomenological analysis and predictions. J. Mater. Sci. 27, 1240 (1992).CrossRefGoogle Scholar
11SourcesThird Generation Hard X-ray Synchrotron Radiation Source Properties, Optics, and Experimental Techniques, edited by Mills, D.M. (Wiley, USA, 2002).Google Scholar
12Zhao, Y., Wang, C.C., and Lu, T.M.: Characterization of Amorphous Crystalline Rough Principles and Applications (Academic Press, Elsevier, USA, 2001).Google Scholar
13Spaepen, F.: A microscopic mechanism for steady state inhomogeneous flow in metallic glasses. Acta Metall. 25, 407 (1977).CrossRefGoogle Scholar