Hostname: page-component-586b7cd67f-dsjbd Total loading time: 0 Render date: 2024-11-24T12:51:05.336Z Has data issue: false hasContentIssue false
  • English
  • Français

Retardation of cyclic indentation creep exhibited in metal alloys

Published online by Cambridge University Press:  31 January 2011

Pal Jen Wei ,
Yun Che Wang  and
Jen Fin Lin
Pal Jen Wei
Affiliation:
Department of Mechanical Engineering, National Cheng Kung University, Tainan, Taiwan 701
Yun Che Wang
Affiliation:
Center for Micro/Nano Science and Technology and Department of Civil Engineering, National Cheng Kung University, Tainan, Taiwan 701
Jen Fin Lin*
Affiliation:
Center for Micro/Nano Science and Technology and Institute of Nanotechnology and Microsystems Engineering, National Cheng Kung University, Tainan, Taiwan 701
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Depth penetration per cycle and its retardation exhibited in specimens of 6061 Al were studied. By holding the maximum load reached during loading prior to cyclic oscillating, the creep could be effectively attenuated from the cyclic indentation. Constant depth penetration of sub-nanometers per cycle was found. The interrupt segments with different amplitudes (over- and underloading) or frequencies (frequency increasing and decreasing), but with same mean load, induced immediate retardations of cyclic indentation. As the interrupt segments have more than 10 cycles, the retardation is enhanced with the increase of cycle number. Accumulation of strain hardening due to stress concentration under the indenter tip is proposed to be the mechanism by which interrupt oscillation retards subsequent cyclic indentation.

Keywords

MetalNano-indentationNanoscale
Type
Articles
Information
Journal of Materials Research , Volume 23 , Issue 10 , October 2008 , pp. 2650 - 2656
Copyright
Copyright © Materials Research Society 2008

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Evans, J.T., Parkins, R.N.: Creep induced by cyclic loading in a C–Mn steel. Acta Metall. 24, 511 1976CrossRefGoogle Scholar
2Bennett, P.S.G., Evans, J.T.: Creep stimulated by interrupted loading in copper and copper–1% cadmium. Mater. Sci. Eng. 38, 111 1979CrossRefGoogle Scholar
3Yang, F.Q., Saran, A.: Cyclic indentation of an elastic–perfectly plastic material. J. Mater. Sci. 41, 6077 2006CrossRefGoogle Scholar
4Xu, B.X., Yue, Z.F.: Study of the ratcheting by the indentation fatigue method with a flat cylindrical indenter: Part II. Finite element simulation. J. Mater. Res. 21(7), 1793 2006CrossRefGoogle Scholar
5Yang, F.Q., Peng, L.L., Okazaki, K.: Creep indentation in aluminum. J. Mater. Sci. 42, 4513 2007CrossRefGoogle Scholar
6Xu, B.X., Yue, Z.F.: Study of the ratcheting by the indentation fatigue method with a flat cylindrical indenter: Part I. Experimental study. J. Mater. Res. 22(1), 186 2007CrossRefGoogle Scholar
7Li, J.C.M., Chu, S.N.G.: Impression fatigue. Scr. Mater. 13, 1021 1979Google Scholar
8Li, J.C.M.: Impression creep and other localized tests. Mater. Sci. Eng., A 322, 23 2002CrossRefGoogle Scholar
9Kaszynski, P., Ghorbel, E., Marquis, D.: An experimental study of ratcheting during indentation of 316L stainless steel. J. Eng. Mater. Technol. 120, 218 1998CrossRefGoogle Scholar
10Alfredsson, B., Olsson, M.: Standing contact fatigue. Fatigue Fract. Eng. Mater. Struct. 22, 225 1999CrossRefGoogle Scholar
11Alfredsson, B., Olsson, M.: Initiation and growth of standing contact fatigue cracks. Eng. Fract. Mech. 65, 89 2000CrossRefGoogle Scholar
12Alfredsson, B., Olsson, M.: Standing contact fatigue testing of a ductile material. Fatigue Fract. Eng. Mater. Struct. 23, 229 2000CrossRefGoogle Scholar
13Abudaia, F.B., Evans, J.T., Shaw, B.A.: Spherical indentation fatigue cracking. Mater. Sci. Eng., A 391, 181 2005CrossRefGoogle Scholar
14Evans, J.T., Lu, F.X.: Plastic deformation and fatigue crack growth in grain-oriented Fe–3.5% Si. Acta Metall. 30(4), 751 1982CrossRefGoogle Scholar
15Johnson, K.L.: Contact Mechanics Cambridge University Press Cambridge, England 1985CrossRefGoogle Scholar
16Johnson, K.L.: The correlation of indentation experiments. J. Mech. Phys. Solids 18, 115 1970CrossRefGoogle Scholar
17Kral, E.N., Komvopoulos, K., Bogy, D.B.: Elastic–plastic finite element analysis of repeated indentation of a half-space by a rigid sphere. ASME J. Appl. Mech. 60, 829 1993CrossRefGoogle Scholar
18Nagn, A.H.W., Tang, B.: Viscoelastic effects during unloading in depth-sensing indentation. J. Mater. Res. 17(10), 2604 2002Google Scholar
19Oyen, M.L., Cook, R.F.: Load–displacement behavior during sharp indentation of viscous–elastic–plastic materials. J. Mater. Res. 18(1), 139 2003CrossRefGoogle Scholar
20Zhang, Y.W., Yang, S.: Analysis of nanoindentation creep for polymeric materials. J. Appl. Phys. 95(7), 3655 2004Google Scholar
21Wang, S.H., Chen, W.X.: A study on the per-cyclic-load–induced burst of creep deformation of a pipeline steel under sequent static load. Mater. Sci. Eng., A 325, 144 2002CrossRefGoogle Scholar