Hostname: page-component-78c5997874-dh8gc Total loading time: 0 Render date: 2024-11-08T00:06:08.589Z Has data issue: false hasContentIssue false
  • English
  • Français

Processing of high-strain-rate superplastic Si3N4w/Al–Mg–Si composites

Published online by Cambridge University Press:  03 March 2011

Mamoru Mabuchi  and
Kenji Higashi
Mamoru Mabuchi
Affiliation:
National Industrial Research Institute of Nagoya, Hirate-cho, Kita-ku, Nagoya, 462, Japan
Kenji Higashi
Affiliation:
Department of Mechanical Systems Engineering, College of Engineering, University of Osaka Prefecture, Gakuen-cho, Sakai, Osaka, 591, Japan
Get access

Abstract

Effects of reduction, reinforcements, and dynamic precipitation on grain refinement by hot extrusion have been investigated in a Si3N4w/Al-Mg-Si (6061) composite by tensile tests and microstructural investigation. The grain refinement was attributed to an interaction of recrystallization and dynamic precipitation, which was enhanced by reinforcements. Not only fine-grained microstructure, but also relaxing stress concentrations which are caused at matrix/reinforcement interfaces during superplastic flow are required to attain large elongations. Partial melting resulting from segregation plays an important role in relaxing the stress concentrations. DSC investigations revealed that the degree of segregation was increased by hot extrusion.

Type
Articles
Information
Journal of Materials Research , Volume 10 , Issue 10 , October 1995 , pp. 2494 - 2502
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Nieh, T. G., Henshall, C. A., and Wadsworth, J., Scripta Metall. 18, 1405 (1984). Lett. 9, 255 (1990).CrossRefGoogle Scholar
5Xiaoxu, H., Qing, L., Yao, C. K., and Mei, Y., J. Mater. Sci. Lett. 10, 964 (1991).CrossRefGoogle Scholar
6Mabuchi, M., Imai, T., Kubo, K., Higashi, K., Okada, Y., and Tanimura, S., Mater. Lett. 11, 339 (1991).CrossRefGoogle Scholar
7Mabuchi, M., Higashi, K., Okada, Y., Tanimura, S., Imai, T., and Kubo, K., Scripta Metall. Mater. 25, 2.517 (1991).CrossRefGoogle Scholar
8Higashi, K., Okada, T., Mukai, T., Tanimura, S., Nieh, T. G., and Wadsworth, J., Scripta Metall. Mater. 26, 185 (1992).CrossRefGoogle Scholar
9Mabuchi, M., Higashi, K., and Langdon, T. G., Acta Metall. Mater. 42, 1739 (1994).CrossRefGoogle Scholar
10Mabuchi, M. and Higashi, K., Mater. Trans. JIM 35, 399 (1994).CrossRefGoogle Scholar
11Sherby, O.D. and Wadsworth, J., Prog. Mater. Sci. 33, 169 (1989).CrossRefGoogle Scholar
12Nieh, T. G., Gilman, P. S., and Wadsworth, J., Scripta Metall. 19, 1375 (1985).CrossRefGoogle Scholar
13Bieler, T. R., Nieh, T. G., Wadsworth, J., and Mukherjee, A. K., Scripta Metall. 22, 81 (1988).CrossRefGoogle Scholar
14Higashi, K., Okada, T., Mukai, T., and Tanimura, S., Scripta Metall. Mater. 25, 2053 (1991).CrossRefGoogle Scholar
15Higashi, K., Mater. Sci. Eng. A A166, 109 (1993).CrossRefGoogle Scholar
16Wert, E. A., Paton, N. E., Hamilton, C. H., and Mahoney, M.W., Metall. Trans. A 12A, 1267 (1981).CrossRefGoogle Scholar
17Watts, B. M., Stowell, M. J., Baikie, B. L., and Owen, D. G. E., Metal. sci. 10, 189 (1976).Google Scholar
18Watts, B. M., Stowell, M. J., Baikie, B. L., and Owen, D. G. E., Metal. Sci. 10, 198 (1976).Google Scholar
19Nes, E., J. Mater. Sci. 13, 2052 (1978).CrossRefGoogle Scholar
20McNelley, T. R., Lee, E-W., and Mills, M.E., Metall. Trans. A 17A, 1035 (1986).CrossRefGoogle Scholar
21Lee, E-W., McNelley, T.R., and Stengle, A.F., Metall. Tarns. A 17A, 1043 (1986).CrossRefGoogle Scholar
22Hales, S. J. and McNelley, T.R., Acta Metall. 36, 1229 (1988).CrossRefGoogle Scholar
23Hales, S. J., McNelley, T.R., and McQueen, H.J., Metall. Trans. A 22A, 1037 (1991).CrossRefGoogle Scholar
24Mabuchi, M. and Higashi, K., in Recrystallization '92, edited by Fuentes, M. and Sevillano, J.G. (Trans Tech Publications, Aedermannsdorf, Switzerland, 1992), p. 545.Google Scholar
25Nieh, T.G. and Wadsworth, J., Mater. Sci. Eng. A A147, 129 (1991).CrossRefGoogle Scholar
26Nieh, T. G., Wadsworth, J., and Imai, T., Scripta Metall. Mater. 26, 703 (1992).CrossRefGoogle Scholar
27Mabuchi, M. and Higashi, K., Philos. Mag. Lett. 70, 1 (1994).CrossRefGoogle Scholar
28Koike, J., Mabuchi, M., and Higashi, K., Acta Metall. Mater. 43, 199 (1995).CrossRefGoogle Scholar
29Koike, J., Mabuchi, M., and Higashi, K., J. Mater. Res. 10, 133 (1995).CrossRefGoogle Scholar
30Mohamed, F. A. and Langdon, T. G., Acta Metall. 23, 117 (1975).CrossRefGoogle Scholar
31Gifkins, R. C., Metall. Trans. A 7A, 1225 (1976).CrossRefGoogle Scholar
32Shei, S-A. and Langdon, T. G., Acta Metall. 26, 639 (1978).CrossRefGoogle Scholar
33Arieli, A., Yu, A.K.S., and Mukherjee, A.K., Metall. Trans. A 11A, 181 (1980).CrossRefGoogle Scholar
34Hamilton, C. H., Bampton, C. C., and Paton, N.E., in Superplastic Forming of Structural Alloys, edited by Paton, N.E. and Hamilton, C.H. (The Metallurgical Society of AIME, San Diego, CA, 1982), p. 173.Google Scholar
35Dutta, I., Tiedemann, C. F., and McNelley, T.R., Scripta Metall. Mater. 24, 1233 (1990).CrossRefGoogle Scholar
36Zaidi, M. A. and Sheppard, T., Metal Sci. 16, 229 (1982).CrossRefGoogle Scholar
37Sheppard, T. and Tutcher, M. G., Metal Sci. 14, 579 (1980).CrossRefGoogle Scholar
38Humphreys, F. J., Metal Sci. 13, 136 (1979).CrossRefGoogle Scholar
39Humphreys, F. J., Mater. Sci. Eng. A A135, 267 (1991).CrossRefGoogle Scholar
40Christman, T. and Suresh, S., Acta Metall. 36, 1691 (1988).CrossRefGoogle Scholar
41Iwasaki, H., Takeuchi, M., Mori, T., Mabuchi, M., and Higashi, K., Scripta Metall. Mater. 31, 255 (1994).CrossRefGoogle Scholar
42Higashi, K. and Mabuchi, M., Mater. Sci. Eng. A A176, 461 (1994).CrossRefGoogle Scholar
43Higashi, K., Nieh, T. G., and Wadsworth, J., Mater. Sci. Eng. A A188, 167 (1994).CrossRefGoogle Scholar
44Raj, R. and Ashby, M. F., Acta Metall. 23, 653 (1975).CrossRefGoogle Scholar
45Aluminum Handbook, 4th ed. (Japan Inst. of Light Metals, Tokyo, Japan, 1990), p. 25.Google Scholar
46Srolovitz, D. J., Luton, M. J., Petkovic-Luton, R., Bamett, D. M., and Nix, W. D., Acta Metall. 32, 1079 (1984).CrossRefGoogle Scholar
47Nardone, V. C., Matejczyk, D. E., and Tien, J. K., Acta Metall. 32, 1509 (1984).CrossRefGoogle Scholar
48Rahaman, M. N., Boiteux, Y., and Jonghe, L. C. D., Am. Ceram. Soc. Bull. 65, 1171 (1986).Google Scholar
49Pickard, S. M., Derby, B., and Feest, E. A., J. Mater. Sci. 26, 6207 (1991).CrossRefGoogle Scholar