Hostname: page-component-586b7cd67f-g8jcs Total loading time: 0 Render date: 2024-11-25T05:45:53.210Z Has data issue: false hasContentIssue false
  • English
  • Français

A parametric study of titanium silicide formation by rapid thermal processing

Published online by Cambridge University Press:  31 January 2011

A. V. Amorsolo Jr. ,
P. D. Funkenbusch  and
A. M. Kadin
A. V. Amorsolo Jr.
Affiliation:
Department of Mechanical Engineering, University of Rochester, Rochester, New York 14627
P. D. Funkenbusch
Affiliation:
Department of Mechanical Engineering, University of Rochester, Rochester, New York 14627
A. M. Kadin
Affiliation:
Department of Electrical Engineering, University of Rochester, Rochester, New York 14627
Get access

Abstract

A parametric study of titanium silicide formation by rapid thermal processing was conducted to determine the effects of annealing temperature (650 °C, 750 °C), annealing time (30 s, 60 s), wet etching (no HF dip, with HF dip), sputter etching (no sputter etch, with sputter etch), and annealing ambient (Ar, N2) on the completeness of conversion of 60 nm Ti on (111)-Si to C54–TiSi2 based on sheet resistance and the uniformity of the sheet resistance measurements across the entire wafer. Statistical analysis of the results showed that temperature, annealing ambient, and sputter etching had the greatest influence. Increasing the temperature and using argon gas instead of nitrogen promoted conversion of the film to C54–TiSi2. On the other hand, sputter etching retarded it. The results also indicated significant interactions among these factors. The best uniformity in sheet resistance was obtained by annealing at 750 °C without sputter etching. The different sheet resistance profiles showed gradients that were consistent with expected profile behaviors, arising from temperature variations across the wafer due to the effect of a flowing cold gas and the effects of the wafer edge and flats.

Type
Articles
Information
Journal of Materials Research , Volume 11 , Issue 2 , February 1996 , pp. 412 - 421
Copyright
Copyright © Materials Research Society 1996

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Chen, L. and Tu, K., Mat. Sci. Rep. 6, 53 (1991).CrossRefGoogle Scholar
2.Osburn, C., in Rapid Thermal Processing, Science and Technology, edited by Fair, R. B. (Academic Press, Inc., Boston, 1993), p. 227.CrossRefGoogle Scholar
3.Clevenger, L. A. and Mann, R.W., in Silicides, Germanides, and Their Interfaces, edited by Fathauer, R. W., Mantl, S., Schowalter, L. J., and Tu, K. N. (Mater. Res. Soc. Symp. Proc. 320, Pittsburgh, PA, 1994), p. 15.Google Scholar
4.Winnerl, J., in Silicides, Germanides, and Their Interfaces, edited by Fathauer, R. W., Mantl, S., Schowalter, L.J., and Tu, K.N. (Mater. Res. Soc. Symp. Proc. 320, Pittsburgh, PA, 1994), p. 37.Google Scholar
5.Chen, L. J., Lur, W., Chen, J.F., Lee, T.L., and Liang, J.M., in Rapid Thermal and Integrated Processing III, edited by Wortman, J. J., Gelpey, J. C., Green, M.L., Brueck, S. R. J., and Roozeboom, F. (Mater. Res. Soc. Symp. Proc. 342, Pittsburgh, PA, 1994), p. 99.Google Scholar
6.Jeon, H., Sukow, C. A., Honeycutt, J. W., Humphreys, T.P., Nemanich, R. J., and Rozgonyi, G. A., in Advanced Metallizations in Microelectronics, edited by Katz, A., Murarka, S. P., and Appelbaum, A. (Mater. Res. Soc. Symp. Proc. 181, Pittsburgh, PA, 1990), p. 569.Google Scholar
7.Mann, R., Racine, C., and Bass, R., in Rapid Thermal and Integrated Processing, edited by Gelpey, J., Green, M., Singh, R., and Wortman, J. (Mater. Res. Soc. Symp. Proc. 224, Pittsburgh, PA, 1991), p. 115.Google Scholar
8.Nanda, A. K., Meester, S., and Wilkins, C. W., in Rapid Thermal and Integrated Processing III, edited by Wortman, J.J., Gelpey, J.C., Green, M. L., Brueck, S. R. J., and Roozeboom, F. (Mater. Res. Soc. Symp. Proc. 342, Pittsburgh, PA, 1994), p. 111.Google Scholar
9.Winnerl, J., Semiconductor Int. 17, 81 (Aug. 1994).Google Scholar
10.Chen, S., Sakamoto, A., Tamura, H., Yoshimaru, M., and Ino, M., in Advanced Metallizations in Microelectronics, edited by Katz, A., Murarka, S. P., and Appelbaum, A. (Mater. Res. Soc. Symp. Proc. 181, Pittsburgh, PA, 1990), p. 179.Google Scholar
11.Nulman, J., in Advanced Metallizations in Microelectronics, edited by Katz, A., Murarka, S. P., and Appelbaum, A. (Mater. Res. Soc. Symp. Proc. 181, Pittsburgh, PA, 1990), p. 123.Google Scholar
12.Chen, W. M., Lee, J. C., and Frost, M. R., in Silicides, Germanides, and Their Interfaces, edited by Fathauer, R. W., Mantl, S., Schowalter, L. J., and Tu, K. N. (Mater. Res. Soc. Symp. Proc. 320, Pittsburgh, PA, 1994), p. 47.Google Scholar
13.Wang, A. and Lien, J., in VLSI Science and Technology/1985 Proceedings of the Third International Symposium on Very Large Scale Integration Science and Technology, edited by Bullis, W. M. and Broydo, S. (The Electrochemical Society, Inc., Pennington, NJ, 1985), Vol. 85–5, p. 203.Google Scholar
14.Norstrom, H., Maex, K., and Vandenabeele, P., in Advanced Metallizations in Microelectronics, edited by Katz, A., Murarka, S. P., and Appelbaum, A. (Mater. Res. Soc. Symp. Proc. 181, Pittsburgh, PA, 1990), p. 173.Google Scholar
15.Fulks, R., in Rapid Thermal Processing of Electronic Materials, edited by Wilson, S. R., Powell, R., and Davies, D. E. (Mater. Res. Soc. Symp. Proc. 92, Pittsburgh, PA, 1987), p. 249.Google Scholar
16.Hodul, D. and Mehta, S., in Rapid Thermal Processing of Electronic Materials, edited by Wilson, S. R., Powell, R., and Davies, D. E. (Mater. Res. Soc. Symp. Proc. 92, Pittsburgh, PA, 1987), p. 183.Google Scholar
17.Fair, R. B., in Rapid Thermal Processing, Science and Technology, edited by Fair, R. B. (Academic Press, Inc., Boston, 1993), p. 1.Google Scholar
18.Jeon, H., Sukow, C. A., Honeycutt, J.W., Rozgonyi, G. A., and Nemanich, R. J., J. Appl. Phys. 71, 4269 (1992).CrossRefGoogle Scholar
19.Richter, F., Bugiel, E., Erzgraber, H. B., and Panknin, D., J. Appl. Phys. 72, 815 (1992).CrossRefGoogle Scholar
20.Clevenger, L. A., Mann, R. W., Roy, R. A., Saenger, K. L., Cabral, C. Jr., and Piccirillo, J., J. Appl. Phys. 76, 7874 (1994).CrossRefGoogle Scholar
21.Phadke, M. S., Quality Engineering Using Robust Design (Prentice Hall, Englewood Cliffs, NJ, 1989).Google Scholar
22.Lochner, R. H. and Matar, J. E., Designing for Quality (Quality Resources, White Plains, NY, 1990).Google Scholar
23.Petersen, R. G., Design and Analysis of Experiments (Marcel Dekker, Inc., New York, 1985), pp. 112, 167.Google Scholar
24.Montgomery, D. C., Design and Analysis of Experiments, 3rd ed. (John Wiley & Sons, New York, 1991), pp. 270, 377.Google Scholar
25.Rickmers, A. D. and Todd, H. N., Statistics, An Introduction (McGraw-Hill Book Company, New York, 1967), pp. 289, 335.Google Scholar
26.Sze, S. M., Semiconductor Devices, Physics and Technology (John Wiley and Sons, New York, 1985).Google Scholar
27.Maissel, L. I., in Handbook of Thin Film Technology, edited by Maissel, L.I. and Glang, R. (McGraw-Hill Book Company, New York, 1970), p. 13–5.Google Scholar
28.Murarka, S. P., Silicides for VLSI Applications (Academic Press, Inc., Orlando, FL, 1983).Google Scholar
29.Naeem, M. D., Orr-Arienzo, W. A., and Rapp, J.G., Appl. Phys. Lett. 66, 877 (1995).CrossRefGoogle Scholar
30.Nicolet, M. and Lau, S., in VLSI Handbook, edited by Einspruch, N. G. (Academic Press, Inc., Orlando, FL, 1985), p. 415.CrossRefGoogle Scholar
31.Ma, Z., Ramanath, G., and Allen, L. H., in Silicides, Germanides and Their Interfaces, edited by Fathauer, R. W., Mantl, S., Schowalter, L. J., and Tu, K. N. (Mater. Res. Soc. Symp. Proc. 320, Pittsburgh, PA, 1994), p. 361.Google Scholar
32.Berry, R. W., Hall, P. M., and Harris, M. T., Thin Film Technology (D. Van Nostrand Company, Inc., Princeton, NJ, 1968).Google Scholar
33.Vossen, J. L. and Cuomo, J., in Thin Film Processes, edited by Vossen, J. L. and Kern, W. (Academic Press, Inc., New York, 1978), p. 12.Google Scholar
34.Beyers, R., Coulman, D., and Merchant, P., J. Appl. Phys. 61, 5110 (1987).CrossRefGoogle Scholar
35.Beyers, R. and Sinclair, R., J. Appl. Phys. 57, 5240 (1985).CrossRefGoogle Scholar
36.Clevenger, L. A., Harper, J. M. E., Cabral, C. Jr., Nobili, C., Ottaviani, G., and Mann, R., J. Appl. Phys. 72, 4978 (1992).CrossRefGoogle Scholar
37.Srikrishna, K., Jairath, R., and Huglin, G., in Rapid Thermal and Integrated Processing, edited by Gelpey, J., Green, M., Singh, R., and Wortman, J. (Mater. Res. Soc. Symp. Proc. 224, Pittsburgh, PA, 1991), p. 123.Google Scholar