Hostname: page-component-586b7cd67f-dsjbd Total loading time: 0 Render date: 2024-11-24T18:41:27.770Z Has data issue: false hasContentIssue false
  • English
  • Français

Novel yttrium-stabilized zirconia polymeric precursor for the fabrication of thin films

Published online by Cambridge University Press:  03 March 2011

Roger M. Smith ,
Xiao-Dong Zhou ,
Wayne Huebner  and
Harlan U. Anderson
Roger M. Smith
Affiliation:
Department of Ceramic Engineering, Electronic Materials Appplied Research Center, University of Missouri-Rolla, Rolla, Missouri 65401
Xiao-Dong Zhou*
Affiliation:
Department of Ceramic Engineering, Electronic Materials Appplied Research Center, University of Missouri-Rolla, Rolla, Missouri 65401
Wayne Huebner
Affiliation:
Department of Ceramic Engineering, Electronic Materials Appplied Research Center, University of Missouri-Rolla, Rolla, Missouri 65401
Harlan U. Anderson
Affiliation:
Department of Ceramic Engineering, Electronic Materials Appplied Research Center, University of Missouri-Rolla, Rolla, Missouri 65401
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

An acetate-based polymeric precursor for producing yttrium-stabilized zirconia (YSZ) was developed. The precursor was prepared under ambient conditions and contains only yttrium and zirconium cations. Dense, crack-free films were fabricated with this precursor on alumina substrates at a rate of 60 nm per deposition, producing polycrystalline YSZ at temperatures as low as 600 °C. Grain growth in thin YSZ films followed Arrhenius equation with an activation energy approximately 0.45 eV. The residual strain in YSZ films decreased with increasing annealing temperature from 600 to 900 °C.

Keywords

Thin filmCoating
Type
Articles
Information
Journal of Materials Research , Volume 19 , Issue 9 , September 2004 , pp. 2708 - 2713
Copyright
Copyright © Materials Research Society 2004

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Bean, K.E.: Chemical vapor deposition applications in microelectronics processing. Thin Solid Films 83, 173 (1981).CrossRefGoogle Scholar
2.Sriprang, N., Kaewchinda, D., Kennedy, J.D. andMilne, S.J.: Processing and Sol chemistry of a triol-based sol-gel route for preparing lead zirconate titanate thin films. J. Am. Ceram. Soc. 83 1914 (2000).CrossRefGoogle Scholar
3.Lackey, W.J., Stinton, D.P., Cerny, G.A., Schaffhauser, A.C. andFehrenbacher, L.L.: Ceramic coatings for advanced heat engines— A review and projection. Adv. Ceram. Mater. 2 24 (1987).CrossRefGoogle Scholar
4.van der Straten, P.J.M. andVerspui, G.: Chemical vapor deposition of wear-resistant coatings on tool steel. Phillips Tech. Rev. 40 204 (1982).Google Scholar
5.Souza, S., Visco, S.J. andDe Jonghe, L.C.: Thin-film solid oxide fuel cell with high performance at low-temperature. Solid State Ionics 98 57 (1997).CrossRefGoogle Scholar
6.Gorman, B.P. andAnderson, H.U.: Synthesis and microstructural characterization of unsupported nanocrystalline zirconia thin films. J. Am. Ceram. Soc. 84 890 (2001).CrossRefGoogle Scholar
7.Thornton, J.A. andGreene, J.E.Sputter deposition processes—Handbook of deposition technologies for films and coatings (Noyes Publications, NJ, 1994) pp. 249–319Google Scholar
8.Maddox, D.M.Ion plating technology—Handbook of deposition technologies for films and coatings (Noyes Publications, New Jersey, 1994) pp. 320–373Google Scholar
9.Bryant, W.A.: Review: The fundamentals of chemical vapor deposition. J. Mater. Sci. 12 1285 (1977).CrossRefGoogle Scholar
10.Brinker, C.J., Scherer, G.W. and Sol-Gel Science: The Physics and Chemistry of Sol-Gel Processing (Academic Press, New York, 1990), p. 2Google Scholar
11.Scriven, L.E. Physics and applications of dip coating and spin coating, in Better Ceramics Through Chemistry III, edited by Brinker, C.J., Clark, D.E., and Ulrich, D.R. (Mater. Res. Soc. Symp. Proc. 121, Pittsburgh, PA, 1988) p. 717Google Scholar
12.Anderson, H.U., Nasrallah, M.M., and Chen, C.C.: Method of coating a substrate with a metal oxide film from an aqueous solution comprising a metal cation and a polymerizable organic solvent. U.S. Patent No. 5 494 700 (1996).Google Scholar
13.Howard, W.L. and Wilson, D.A., Chelating Agents: Encyclopedia of Chemical Technology. Vol. 5, 4th ed. (Wiley, New York, 1993), pp. 764–795.Google Scholar
14.Peshev, P. andSlavova, V.: Preparation of yttria-stabilized zirconia thin films by a sol-gel procedure using alkoxide presursors. Mater. Res. Bull. 27 1269 (1992).CrossRefGoogle Scholar
15.Scott, C.E. andReed, J.S.: Analysis of Cl- ions laundered from submicron zirconia powders. Bull. Am. Ceram. Soc. 57 741 (1978).Google Scholar
16.Scott, C.E. andReed, J.S.: Effect of laundering and milling on the sintering behavior of stabilized zirconia powders. Bull. Am. Ceram. Soc. 58 587 (1979).Google Scholar
17.Dahlstrom, D.A. Selection of Solid-Liquid Separation Equipment, in Advances in Solid-Liquid Separation, edited by Muralidhara, H.S. (Battelle Columbus Laboratories, Battelle Press, Ohio, 1986)Google Scholar
18.Bernstein, E., Blanchin, M.G. andSamdi, A.: Structural characteristics of ZrO2 powders prepared from acetates. Ceram. Int. 15 337 (1989).CrossRefGoogle Scholar
19.Geiculescu, A.C. andRack, H.J.: X-ray scattering studies of polymeric zirconia species in aqueous xerogels. J. Non-Cryst. Solids 306 30 (2002).CrossRefGoogle Scholar
20.Schwartz, R.W.: Chemical solution deposition of perovskite thin films. Chem. Mater. 9 2325 (1997).CrossRefGoogle Scholar
21.Pennell, M.J. The development of the ethylene glycol process for the synthesis of ceramic oxides. Master of Science Thesis, University of Missouri—Rolla, MO (1988)Google Scholar
22.Moriguchi, I., Tsujigo, Y., Teraoka, Y. andKagawa, S.: Role of n-octadecylacetoacetate as an amphiphilic chelating agent in the two-dimensional sol-gel systhesis of ultrathin films of titania and zirconia. J. Phys. Chem. B 104 8101 (2000).CrossRefGoogle Scholar
23.Klug, H.P. andAlexander, L.E.X-Ray Diffraction Procedure, 2nd ed. (Wiley, New York, 1974)Google Scholar
24.Zhou, X-D. andHuebner, W.: Size-induced lattice relaxation in CeO2 nanoparticles. Appl. Phys. Lett. 79 3512 (2001).CrossRefGoogle Scholar
25.Jouanne, M., Morhange, J.F., Kanehisa, M.A., Haro-Poniatowski, E., Fuentes, G.A., Torres, E. andHernandez-Tellez, E.: Structural transformation of nanosized zirconium oxide. Phys. Rev. B 64 155404 (2001).CrossRefGoogle Scholar
26.Zhou, X-D., Huebner, W. andAnderson, H.U.: Room-temperature homogeneous nucleation synthesis and thermal stability of nanometer single crystal CeO2. Appl. Phys. Lett. 80 3814 (2001).CrossRefGoogle Scholar
27.Minh, N.Q. and Takahashi, T., Science and Technology of Ceramic Fuel Cells (Elsevier Science, New York, 1995)Google Scholar
28.Barsoum, M.W.Fundamentals of Ceramics (McGraw-Hill, 1997)Google Scholar
29.Kosacki, I., Suzuki, T., Huebner, W., and Anderson, H.U.: Microstructure controlled electrical conductivity in acceptor-doped ZrO2 thin films, in Proceedings of the 7th International Symposium on Solid Oxide Fuel Cells, edited by Yokokawa, H. and Singhal, S.C. (The Electrochemical Society, Inc., New Jersey, 2001) p. 284.Google Scholar