Hostname: page-component-586b7cd67f-tf8b9 Total loading time: 0 Render date: 2024-11-24T14:55:48.616Z Has data issue: false hasContentIssue false
  • English
  • Français

Nanoindentation-derived elastic modulus of an amorphous polymer and its sensitivity to load-hold period and unloading strain rate

Published online by Cambridge University Press:  31 January 2011

N. Fujisawa  and
M.V. Swain
N. Fujisawa*
Affiliation:
Department of Electronic Materials Engineering, Research School of Physical Sciences and Engineering, Australian National University, Canberra, Australian Capital Territory 0200, Australia
M.V. Swain
Affiliation:
Biomaterials Science Research Unit, Faculty of Dentistry, University of Sydney, Sydney Dental Hospital, Surry Hills, New South Wales 2010, Australia
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

An amorphous polymer was contacted by a Berkovich indenter using the same loading history but with four different unloading rates following a wide range of load-hold time periods. The strain-rate sensitivity index of the creeping solid was determined at each load-hold period based on two readily determinable parameters, which are the effective contact stiffness and strain rate at the onset of unloading. The measured strain-rate sensitivity index was found to increase with decreasing load-hold period, suggesting that the elastic moduli of the amorphous polymers determined by nanoindentation (together with the true contact area) depends significantly on the selection of the load-hold period. The rheological condition of the creeping solid under constant load changes substantially with time to affect the subsequent unloading recovery process. It is therefore advisable to control not only the unloading strain rate but also the load-hold period when testing time-dependent materials.

Keywords

Elastic propertiesPolymerViscoelasticity
Type
Articles
Information
Journal of Materials Research , Volume 23 , Issue 3 , March 2008 , pp. 637 - 641
Copyright
Copyright © Materials Research Society 2008

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Sneddon, I.N.: The relation between load and penetration in the axisymmetric Boussinesq problem for a punch of arbitrary profile. Int. J. Eng. Sci. 3, 47 1965Google Scholar
2Oliver, W.C., Pharr, G.M.: Measurement of hardness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology. J. Mater. Res. 19, 3 2004Google Scholar
3Oliver, W.C., Pharr, G.M.: An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7, 1564 1992Google Scholar
4Bolshakov, A., Pharr, G.M.: Influences of pileup on the measurement of mechanical properties by load and depth-sensing indentation techniques. J. Mater. Res. 13, 1049 1998Google Scholar
5Ngan, A.H.W., Wang, H.T., Tang, B., Sze, K.Y.: Correcting power-law viscoelastic effects in elastic modulus measurement using depth-sensing indentation. Int. J. Solids Struct. 42, 1831 2005CrossRefGoogle Scholar
6Menčík, J., Rauchs, G., Bardon, J., Riche, A.: Determination of elastic modulus and hardness of viscoelastic-plastic materials by instrumented indentation under harmonic load. J. Mater. Res. 20, 2660 2005Google Scholar
7Fujisawa, N., Swain, M.V.: Effect of unloading strain rate on the elastic modulus of a viscoelastic solid determined by nanoindentation. J. Mater. Res. 21, 708 2006Google Scholar
8Cheng, Y-T., Cheng, C-M.: Relationships between initial unloading slope, contact depth, and mechanical properties for conical indentation in linear viscoelastic solids. J. Mater. Res. 20, 1046 2005Google Scholar
9Cheng, Y-T., Cheng, C-M., Ni, W.: Methods of obtaining instantaneous modulus of viscoelastic solids using displacement-controlled instrumented indentation with axisymmetric indenters of arbitrary smooth profiles. Mater. Sci. Eng., A 423, 2 2006Google Scholar
10Fujisawa, N., Swain, M.V.: On the indentation contact area of a creeping solid during constant-strain-rate loading by a sharp indenter. J. Mater. Res. 22, 893 2007Google Scholar
11Feng, G., Ngan, A.H.W.: Effects of creep and thermal drift on modulus measurement using depth-sensing indentation. J. Mater. Res. 17, 660 2002CrossRefGoogle Scholar
12Mayo, M.J., Nix, W.D.: A micro-indentation study of superplasticity in Pb, Sn, and Sn-38 wt% Pb. Acta Metall. 36, 2183 1988Google Scholar
13Tang, B., Ngan, A.H.W.: Accurate measurement of tip-sample contact size during nanoindentation of viscoelastic materials. J. Mater. Res. 18, 1141 2003Google Scholar
14Goble, D.L., Wolff, E.G.: Strain-rate sensitivity index of thermoplastics. J. Mater. Sci. 28, 5986 1993Google Scholar