Hostname: page-component-586b7cd67f-2brh9 Total loading time: 0 Render date: 2024-11-24T19:44:44.540Z Has data issue: false hasContentIssue false
  • English
  • Français

Modeling conical indentation in homogeneous materials and in hard films on soft substrates

Published online by Cambridge University Press:  01 February 2005

Wangyang Ni  and
Yang-Tse Cheng
Wangyang Ni*
Affiliation:
Brown University, Engineering Division, Providence, Rhode Island 02912
Yang-Tse Cheng
Affiliation:
Materials and Processes Laboratory, General Motors Research and Development Center, Warren, Michigan 48090
*
a) Address all correspondence to this author. Present address: Materials and Processes Laboratory, General Motors R&D Center, MS 480-106-224, Warren, MI 48090-9055. e-mail: [email protected]
Get access

Abstract

Dimensional analysis and finite element modeling were conducted to examine conical indentation in homogeneous materials and in hard films on soft substrates. In this paper, the solid materials modeled follow the incremental theory of plasticity with a von-Mises yield surface. The validity of the Oliver–Pharr method was examined. It was found that, for hard films on soft substrates, the Oliver–Pharr method is applicable only when the indentation depth is less than 10% of the film thickness. A linear relationship between the ratio of hardness to reduced modulus and the ratio of reversible work to total work was observed for conical indentation in homogeneous materials and in hard films on soft substrates. This relationship can be used to analyze instrumented indentation experiments.

Keywords

HardnessMechanical propertiesNanoindentation
Type
Articles
Information
Journal of Materials Research , Volume 20 , Issue 2 , February 2005 , pp. 521 - 528
Copyright
Copyright © Materials Research Society 2005

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Bückle, H.: Use of hardness test to determine other material properties, in The Science of Hardness Testing and its Research Applications, edited by Westbrook, J.H. and Conrad, H. (American Society of Metals, Metals Park, OH, 1973), p. 453–487.Google Scholar
2.Xu, Z.H. and Rowcliffe, D.: Finite element analysis of substrate effects on indentation behavior of thin films. Thin Solid Films 447–448, 399 (2004).Google Scholar
3.Jonsson, B. and Hogmark, S.: Hardness measurement of thin films. Thin Solid Films 114, 257 (1984).Google Scholar
4.Burnett, P.J. and Rickerby, D.S.: Assessment of coating hardness. Surf. Eng. 3, 69 (1987).Google Scholar
5.Korsunsky, A.M., McGurk, M.R., Bull, S.J. and Page, T.F.: On the hardness of coated systems. Surf. Coat. Technol. 99, 171 (1998).Google Scholar
6.King, R.B.: Elastic analysis of some punch problems for a layered medium. Int. J. Solids Struct. 23, 1657 (1987).Google Scholar
7.Doerner, M.F. and Nix, W.D.: A method for interpreting the data from depth sensing indentation instruments. J. Mater. Res. 1, 601 (1986).CrossRefGoogle Scholar
8.Bhattacharya, A.K. and Nix, W.D.: Analysis of elastic and plastic deformation associated with indentation testing of thin films on substrates. Int. J. Solids Struct. 24, 1287 (1988).CrossRefGoogle Scholar
9.Gao, H., Chu, C. and Lee, J.: Elastic contact versus indentation modeling of multi-layered materials. Int. J. Solids Struct. 29, 2471 (1992).Google Scholar
10.Mencik, J., Munz, D., Quandt, E., Weppelmann, E.R. and Swain, M.V.: Determination of elastic modulus of thin layers using nanoindentation. J. Mater. Res. 12, 2475 (1997).CrossRefGoogle Scholar
11.Saha, R. and Nix, W.D.: Effects of the substrate on the determination of thin film mechanical properties by nanoindentation. Acta Mater. 50, 23 (2002).CrossRefGoogle Scholar
12.Oliver, W.C. and Pharr, G.M.: An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7, 1564 (1992).Google Scholar
13.Oliver, W.C. and Pharr, G.M.: Measurement of hardness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology. J. Mater. Res. 19, 3 (2004).CrossRefGoogle Scholar
14.Bolshakov, A. and Pharr, G.M.: Influences of pileup on the measurement of mechanical properties by load and depth sensing indentation techniques. J. Mater. Res. 13, 1049 (1998).Google Scholar
15.Cheng, Y-T. and Cheng, C-M.: Effect of ‘sinking in’ and ‘piling up’ on estimating the contact area under load in indentation. Philos. Mag. Lett. 78, 115 (1998).Google Scholar
16.Lim, Y.Y., Chaudhri, M.M. and Enomota, Y.: Accurate determination of the mechanical properties of thin aluminum films deposited on sapphire flats using nanoindentations. J. Mater. Res. 14, 2314 (1999).CrossRefGoogle Scholar
17.Tsui, T.Y. and Pharr, G.M.: Substrate effects on nanoindentation mechanical property measurement of soft films on hard substrates. J. Mater. Res. 14, 292 (1999).CrossRefGoogle Scholar
18.Tunvisut, K., O’Dowd, N.P. and Busso, E.P.: Use of scaling functions to determine mechanical properties of thin coatings from microindentation tests. Int. J. Solids Struct. 38, 335 (2001).CrossRefGoogle Scholar
19.Cheng, Y-T. and Cheng, C-M.: Relationships between hardness, elastic modulus, and the work of indentation. Appl. Phys. Lett. 73, 614 (1998).Google Scholar
20.Cheng, Y-T., Li, Z.Y. and Cheng, C-M.: Scaling relationships for indentation measurements. Philos. Mag. 82, 1821 (2002).Google Scholar
21.Lawn, B.R. and Howes, V.R.: Elastic recovery at hardness indentations. J. Mater. Sci. 16, 2745 (1981).Google Scholar
22.Sakai, M.: Energy principle of the indentation-induced inelastic surface deformation and hardness of brittle materials. Acta Metall. Mater. 41, 1751 (1993).CrossRefGoogle Scholar
23.Menick, J. and Swain, M.V.: Micro-indentation tests with pointed indenters. Mater. Forum 18, 277 (1994).Google Scholar
24.Giannakopoulos, A.E. and Suresh, S.: Determination of elastoplastic properties by instrumented sharp indentation. Scripta Mater. 40, 1191 (1999).Google Scholar
25.Dao, M., Chollacoop, N., Van Vliet, K.J., Venkatesh, T.A. and Suresh, S.: Computational modeling of the forward and reverse problems in instrumented sharp indentation. Acta Mater. 49, 3899 (2001).Google Scholar
26.Malzbender, J. and de With, G.: Energy dissipation, fracture toughness and the indentation load-displacement curves of coated materials. Surf. Coat. Technol. 135, 60 (2000).CrossRefGoogle Scholar
27.Xu, Z.H. and Rowcliffe, D.: Method to determine the plastic properties of bulk materials by nanoindentation. Philos. Mag. A 82, 1893 (2002).Google Scholar
28.Ni, W., Cheng, Y-T., Cheng, C-M. and Grummon, D.S.: An energy-based method for analyzing instrumented spherical indentation experiments. J. Mater. Res. 19, 149 (2004).Google Scholar
29.Sneddon, I.N.: The relaxation between load and penetration in the axisymmetric boussinesq problem for a punch of arbitrary profile. Int. J. Eng. Sci. 3, 47 (1965).Google Scholar
30.Jennett, N.M., Aldrich-Smith, G. and Maxwell, A.S.: Validated measurement of Young’s modulus, Poisson ratio, and thickness for thin coatings by combining instrumented nanoindentation and acoustical measurements. J. Mater. Res. 19, 143 (2004).Google Scholar
31.Schneider, D., Siemroth, P., Schulke, T., Berthold, J., Schultrich, B., Schneider, H.H., Ohr, R. and Petereit, B.: Quality control of ultra-thin and super-hard coatings by laser-acoustics. Surf. Coat. Technol. 153, 252 (2002).Google Scholar
32.Chudoba, T., Griepentrog, M., Duck, A., Schneider, D. and Richter, F.: Young’s modulus measurements on ultra-thin coating. J. Mater. Res. 19, 301 (2004).CrossRefGoogle Scholar
33.Barenblatt, G.I.: Scaling, Self-similarity, and Intermediate Asymptotics (Cambridge University Press, Cambridge, U.K., 1996).Google Scholar