Hostname: page-component-586b7cd67f-dlnhk Total loading time: 0 Render date: 2024-11-28T10:15:45.445Z Has data issue: false hasContentIssue false
  • English
  • Français

Mg-based bulk glassy alloys with high strength above 900 MPa and plastic strain

Published online by Cambridge University Press:  03 March 2011

Guangyin Yuan ,
Cunling Qin  and
Akihisa Inoue
Guangyin Yuan*
Affiliation:
Institute for Materials Research, Tohoku University, Sendai 980-8577, Japan; and School of Materials Science and Engineering, Shanghai Jiaotong University, Shanghai 200030, People's Republic of China
Cunling Qin
Affiliation:
Japan Science and Technology Agency, Sendai 980-8577, Japan
Akihisa Inoue
Affiliation:
Institute for Materials Research, Tohoku University, Sendai 980-8577, Japan
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Bulk metallic glasses with a maximum diameter of 2.5–5 mm were formed in Mg75Cu5Ni10Gd10, Mg70Cu15Ni5Gd10, and Mg65Cu20Ni5Gd10 systems by copper mold casting. There is a clear tendency for glass-forming ability (GFA) to increase with increasing solute content. These bulk glassy alloys exhibit a large supercooled liquid region (ΔTx) of 44–64 K, indicating high thermal stability of the supercooled liquid. The Young’s modulus, fracture strength, elastic elongation limit, and plastic strain are in the range of 54–59 GPa, 854–904 MPa, 1.50–1.55%, and 0.10–0.20%, respectively. The Mg65Cu20Ni5Gd10 alloy exhibited the highest values of Young’s modulus and strength, while the largest plastic strain was obtained for the Mg75Cu5Ni10Gd10 alloy. The bulk Mg–Cu–Ni–Gd-based metallic glasses exhibited distinct enhanced corrosion resistance compared to Mg65Cu25Gd10 glassy alloy in NaCl aqueous solutions. The fabrication of the Mg-based bulk glassy alloys exhibiting a high strength level of about 900 MPa and plastic strains of ∼0.2%, in conjunction with good corrosion resistance, indicates that the Mg-based bulk glassy alloys may be used as a new generation of structural material.

Keywords

Mechanical propertiesMetallic glassX-ray diffraction (XRD)
Type
Articles
Information
Journal of Materials Research , Volume 20 , Issue 2 , February 2005 , pp. 394 - 400
Copyright
Copyright © Materials Research Society 2005

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Inoue, A., Ohtera, K., Kita, K. and Masumoto, T.: New amorphous Mg–Ce–Ni alloys with high strength and good ductility. Jpn. J. Appl. Phys. 27, L2248 (1988).CrossRefGoogle Scholar
2.Inoue, A., Nakamura, T., Nishiyama, N. and Masumoto, T.: Mg–Cu–Y bulk amorphous alloys with high tensile strength produced by a high-pressure die casting method. Mater. Trans. JIM 33, 937 (1992).CrossRefGoogle Scholar
3.Kang, H.G., Park, E.S., Kim, W.T., Kim, D.H. and Cho, H.K.: Fabrication of bulk Mg–Cu–Ag-Y glassy alloy by squeeze casting. Mater. Trans. JIM 41, 846 (2000).CrossRefGoogle Scholar
4.Amiya, K. and Inoue, A.: Thermal stability and mechanical properties of Mg–Y–Cu–M (M = Ag, Pd) bulk amorphous alloys. Mater. Trans. JIM 41, 1460 (2000).CrossRefGoogle Scholar
5.Amiya, K. and Inoue, A.: Preparation of bulk glassy Mg65Y10Cu15Ag5Pd5 alloy of 12 mm in diameter by water quenching. Mater. Trans. 42, 543 (2001).CrossRefGoogle Scholar
6.Men, H. and Kim, D.H.: Fabrication of ternary Mg–Cu–Gd bulk metallic glass with high glass-forming ability under air atmosphere. J. Mater. Res. 18, 1502 (2003).CrossRefGoogle Scholar
7.Ma, H., Ma, E. and Xu, J.: A new Mg65Cu7.5Ni7.5Zn5Ag5Y10 bulk metallic glass with strong glass-forming ability. J. Mater. Res. 18, 2288 (2003).CrossRefGoogle Scholar
8.Ma, H., Xu, J. and Ma, E.: Mg-based bulk metallic glass composites with plasticity and high strength. Appl. Phys. Lett. 83, 2793 (2003).CrossRefGoogle Scholar
9.Lu, Z.P. and Liu, C.T.: Glass formation criterion for various glass-forming systems. Phys. Rev. Lett. 91, 115505 (2003).CrossRefGoogle ScholarPubMed
10.Xu, D., Duan, G. and Johnson, W.L.: Unusual glass-forming ability of bulk amorphous alloys based on ordinary metal copper. Phys. Rev. Lett. 92, 245504 (2004).CrossRefGoogle ScholarPubMed
11.Zhang, Q.S., Zhang, H.F., Deng, Y.F., Ding, B.Z. and Hu, Z.Q.: Bulk metallic glass formation of Cu–Zr–Ti–Sn alloys. Scr. Mater. 49, 273 (2003).CrossRefGoogle Scholar
12.Inoue, A., Kato, A., Zhang, T., Kim, S.G. and Masumoto, T.: Mg–Cu–Y amorphous alloys with high mechanical strengths produced by a metallic mold casting method. Mater. Trans. JIM 32, 609 (1991).CrossRefGoogle Scholar
13.Inoue, A. and Masumoto, T.: Mg-based amorphous alloys. Mater. Sci. Eng. A 173, 1 (1993).CrossRefGoogle Scholar
14.ASM International Handbook Committee, Properties and Selection: Nonferrous Alloys and Pure Metals, in Metals Handbook, 9th edition (ASM International, Materials Park, OH, 1992), Vol. 2, p. 528.Google Scholar
15.Boer, F.R., Boom, R., Mattens, W.C.M., Miedema, A.R. and Niessen, A.K.: Cohesion in Metals (North-Holland, Amsterdam, The Netherlands, 1988).Google Scholar