Hostname: page-component-586b7cd67f-2brh9 Total loading time: 0 Render date: 2024-11-30T11:38:45.979Z Has data issue: false hasContentIssue false
  • English
  • Français

Improvement of microstructure and surface behaviors of welded S50C steel components under electropulsing assisted ultrasonic surface modification

Published online by Cambridge University Press:  05 April 2016

Yongda Ye ,
Jie Kuang ,
Song-Zhu Kure-Chu ,
Guolin Song ,
Zhiyan Sun  and
Guoyi Tang
Yongda Ye
Affiliation:
Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055, People's Republic of China, Key Laboratory for Advanced Materials of Ministry of Education, School of Materials Science and Engineering, Tsinghua University, Beijing 100084, People's Republic of China
Jie Kuang
Affiliation:
Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055, People's Republic of China, Key Laboratory for Advanced Materials of Ministry of Education, School of Materials Science and Engineering, Tsinghua University, Beijing 100084, People's Republic of China
Song-Zhu Kure-Chu
Affiliation:
Department of Chemistry and Bioengineering, Iwate University, Iwate 020-8550, Japan
Guolin Song
Affiliation:
Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055, People's Republic of China
Zhiyan Sun
Affiliation:
Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055, People's Republic of China, Key Laboratory for Advanced Materials of Ministry of Education, School of Materials Science and Engineering, Tsinghua University, Beijing 100084, People's Republic of China
Guoyi Tang*
Affiliation:
Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055, People's Republic of China, Key Laboratory for Advanced Materials of Ministry of Education, School of Materials Science and Engineering, Tsinghua University, Beijing 100084, People's Republic of China
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

The effect of electropulsing assisted ultrasonic surface modification (EUSM) on microstructure and surface properties of S50C steel welded components is investigated. Compared with conventional ultrasonic surface modification (USM) process, EUSM process achieves significant improvements in microstructure, including deeper strengthened layers and gradient microstructure on the surface. The EUSM-induced microstructure results in higher levels of surface compressive residual stress and greater surface microhardness and its effective depth. Conventional USM process is inevitably accompanied by some plastic damages, such as pit and crack defects. The damages, however, can be eliminated to some extent during the EUSM process. These enhancements may be attributed to the thermal and athermal effects caused by electropulsing treatment, which accelerates the mobility of dislocations in the dynamic recrystallization process.

Keywords

hardnessmicrostructure
Type
Articles
Information
Journal of Materials Research , Volume 31 , Issue 14 , 28 July 2016 , pp. 2125 - 2135
Copyright
Copyright © Materials Research Society 2016 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Footnotes

Contributing Editor: Jürgen Eckert

References

REFERENCES

Withers, P.J. and Bhadeshia, H.: Residual stress. Part 1–Measurement techniques. Mater. Sci. Technol. 17(4), 355 (2001).CrossRefGoogle Scholar
Withers, P.J. and Bhadeshia, H.: Residual stress. Part 2–Nature and origins. Mater. Sci. Technol. 17(4), 366 (2001).CrossRefGoogle Scholar
Liu, X.C., Zhang, H.W., and Lu, K.: Strain-induced ultrahard and ultrastable nanolaminated structure in nickel. Science 342(6156), 337 (2013).CrossRefGoogle ScholarPubMed
Moering, J., Ma, X., Chen, G., Miao, P., Li, G., Qian, G., Mathaudhu, S., and Zhu, Y.: The role of shear strain on texture and microstructural gradients in low carbon steel processed by surface mechanical attrition treatment. Scr. Mater. 108, 100 (2015).CrossRefGoogle Scholar
Harding, M.D., Donaldson, I.W., Hexemer, R.L., Gharghouri, M.A., and Bishop, D.P.: Characterization of the microstructure, mechanical properties, and shot peening response of an industrially processed Al–Zn–Mg–Cu PM alloy. J. Mater. Process. Technol. 221, 31 (2015).CrossRefGoogle Scholar
Qiao, H., Zhao, J., Zhang, G., and Gao, Y.: Effects of laser shock peening on microstructure and residual stress evolution in Ti–45Al–2Cr–2Nb–0.2B alloy. Surf. Coat. Technol. 276, 145 (2015).CrossRefGoogle Scholar
Xiong, Y., He, T., Guo, Z., He, H., Ren, F., and Volinsky, A.A.: Effects of laser shock processing on surface microstructure and mechanical properties of ultrafine-grained high carbon steel. Mater. Sci. Eng., A 570, 82 (2013).CrossRefGoogle Scholar
Statnikov, E.S., Zhuravlev, L.V., Alekseev, A.F., Bobylev, Y.A., Shevtsov, E.M., Sokolenko, V.I., and Kulikov, V.F.: Ultrasonic head for strain hardening and relaxation treatment. USSR Inventor's Certificate (472782), (1975).Google Scholar
Cao, X.J., Pyoun, Y.S., and Murakami, R.: Fatigue properties of a S45C steel subjected to ultrasonic nanocrystal surface modification. Appl. Surf. Sci. 256(21), 6297 (2010).CrossRefGoogle Scholar
Ye, C., Telang, A., Gill, A.S., Suslov, S., Idell, Y., Zweiacker, K., Wiezorek, J.M., Zhou, Z., Qian, D., and Mannava, S.R.: Gradient nanostructure and residual stresses induced by ultrasonic nano-crystal surface modification in 304 austenitic stainless steel for high strength and high ductility. Mater. Sci. Eng., A 613, 274 (2014).CrossRefGoogle Scholar
Wu, B., Zhang, L., Zhang, J., Murakami, R., and Pyoun, Y.: An investigation of ultrasonic nanocrystal surface modification machining process by numerical simulation. Adv. Eng. Software 83, 59 (2015).CrossRefGoogle Scholar
Amanov, A., Pyun, Y., and Sasaki, S.: Effects of ultrasonic nanocrystalline surface modification (UNSM) technique on the tribological behavior of sintered Cu-based alloy. Tribol. Int. 72, 187 (2014).CrossRefGoogle Scholar
Cherif, A., Pyoun, Y., and Scholtes, B.: Effects of ultrasonic nanocrystal surface modification (UNSM) on residual stress state and fatigue strength of AISI 304. J. Mater. Eng. Perform. 19(2), 282 (2010).CrossRefGoogle Scholar
Suh, C., Lee, M., and Pyoun, Y.: Fatigue characteristics of SKD-61 by ultrasonic nanocrystal surface modification technology under static load variation. Int. J. Mod. Phys. B 24(15n16), 2645 (2010).CrossRefGoogle Scholar
Wu, B., Wang, P., Pyoun, Y., Zhang, J., and Murakami, R.: Effect of ultrasonic nanocrystal surface modification on the fatigue behaviors of plasma-nitrided S45C steel. Surf. Coat. Technol. 213, 271 (2012).CrossRefGoogle Scholar
Yang, X., Zhou, J., and Ling, X.: Study on plastic damage of AISI 304 stainless steel induced by ultrasonic impact treatment. Mater. Des. 36, 477 (2012).CrossRefGoogle Scholar
Panin, A.V., Kazachenok, M.S., Kozelskaya, A.I., Hairullin, R.R., and Sinyakova, E.A.: Mechanisms of surface roughening of commercial purity titanium during ultrasonic impact treatment. Mater. Sci. Eng., A 647, 43 (2015).CrossRefGoogle Scholar
Kuang, J., Li, X., Ye, X., Tang, J., Liu, H., Wang, J., and Tang, G.: Microstructure and texture evolution of magnesium alloys during electropulse treatment. Metall. Mater. Trans. A 46(4), 1789 (2015).CrossRefGoogle Scholar
Rahnama, A. and Qin, R.S.: Electropulse-induced microstructural evolution in a ferritic–pearlitic 0.14% C steel. Scr. Mater. 96, 17 (2015).CrossRefGoogle Scholar
Ye, X., Tang, G., Song, G., and Kuang, J.: Effect of electropulsing treatment on the microstructure, texture, and mechanical properties of cold-rolled Ti–6Al–4V alloy. J. Mater. Res. 29(14), 1500 (2014).CrossRefGoogle Scholar
Ye, X., Zion, T.H., Tang, G., Li, X., and Song, G.: Effect of electropulsing treatment on microstructure and mechanical properties of cold-rolled pure titanium strips. J. Mater. Process. Technol. 222, 27 (2015).CrossRefGoogle Scholar
Zhu, R., Tang, G., Shi, S., and Fu, M.: Effect of electroplastic rolling on deformability and oxidation of NiTiNb shape memory alloy. J. Mater. Process. Technol. 213(1), 30 (2013).CrossRefGoogle Scholar
Jiang, Y., Guan, L., Tang, G., Shek, C., and Zhang, Z.: Influence of electropulsing treatment on microstructure and mechanical properties of cold-rolled Mg–9Al–1Zn alloy strip. Mater. Sci. Eng., A 528(16), 5627 (2011).CrossRefGoogle Scholar
Kuang, J., Du, X., Li, X., Yang, Y., Luo, A.A., and Tang, G.: Athermal influence of pulsed electric current on the twinning behavior of Mg–3Al–1Zn alloy during rolling. Scr. Mater. 114, 151 (2016).CrossRefGoogle Scholar
Lin, H.Q., Zhao, Y.G., Gao, Z.M., and Han, L.G.: Effects of pulse current stimulation on the thermal fatigue crack propagation behavior of CHWD steel. Mater. Sci. Eng., A 478(1), 93 (2008).CrossRefGoogle Scholar
Zheng, X.G., Shi, Y., and Lu, K.: Electro-healing cracks in nickel. Mater. Sci. Eng., A 561, 52 (2013).CrossRefGoogle Scholar
Hosoi, A., Nagahama, T., and Ju, Y.: Fatigue crack healing by a controlled high density electric current field. Mater. Sci. Eng., A 533, 38 (2012).CrossRefGoogle Scholar
Ye, X., Li, X., Song, G., and Tang, G.: Effect of recovering damage and improving microstructure in the titanium alloy strip under high-energy electropulses. J. Alloys Compd. 616, 173 (2014).CrossRefGoogle Scholar
Levitin, V.V. and Loskutov, S.V.: The effect of a current pulse on the fatigue of titanium alloy. Solid State Commun. 131(3–4), 181 (2004).CrossRefGoogle Scholar
Ye, X., Ye, Y., and Tang, G.: Effect of electropulsing treatment and ultrasonic striking treatment on the mechanical properties and microstructure of biomedical Ti–6Al–4V alloy. J. Mech. Behav. Biomed. Mater. 40, 287 (2014).CrossRefGoogle ScholarPubMed
Ye, X., Liu, T., Ye, Y., Wang, H., Tang, G., and Song, G.: Enhanced grain refinement and microhardness of Ti–Al–V alloy by electropulsing ultrasonic shock. J. Alloys Compd. 621, 66 (2015).CrossRefGoogle Scholar
Ye, X. and Tang, G.: Effect of coupling asynchronous acoustoelectric effects on the corrosion behavior, microhardness and biocompatibility of biomedical titanium alloy strips. J. Mater. Sci.: Mater. Med. 26(1), 1 (2015).Google ScholarPubMed
Wang, H., Song, G., and Tang, G.: Enhanced surface properties of austenitic stainless steel by electropulsing-assisted ultrasonic surface rolling process. Surf. Coat. Technol. 282, 149 (2015).CrossRefGoogle Scholar
Liu, D., Li, X., Tang, G., Chen, L., Wang, H., and Song, G.: Improvement of surface properties of 2316 stainless steel with ultrasonic electric surface modification. Mater. Sci. Technol. 31(13a), 1572 (2015).CrossRefGoogle Scholar
Withers, P.J., Turski, M., Edwards, L., Bouchard, P.J., and Buttle, D.J.: Recent advances in residual stress measurement. Int. J. Pressure Vessels Piping 85(3), 118 (2008).CrossRefGoogle Scholar
Coules, H.E.: Contemporary approaches to reducing weld induced residual stress. Mater. Sci. Technol. 29(1), 4 (2013).CrossRefGoogle Scholar
Rossini, N.S., Dassisti, M., Benyounis, K.Y., and Olabi, A.G.: Methods of measuring residual stresses in components. Mater. Des. 35, 572 (2012).CrossRefGoogle Scholar
Martins, C., Strohaecker, T.R., Rocha, A.S., and Hirsch, T.K.: Application of X-ray diffraction, micromagnetic and hole drilling methods for residual stress determination in a ball bearing steel ring. Exp. Mech. 45(4), 344 (2005).CrossRefGoogle Scholar
Schajer, G.S.: Hole-drilling residual stress measurements at 75: Origins, advances, opportunities. Exp. Mech. 50(2), 245 (2010).CrossRefGoogle Scholar
Beghini, M., Bertini, L., and Santus, C.: A procedure for evaluating high residual stresses using the blind hole drilling method, including the effect of plasticity. J. Strain Anal. Eng. Des. 45(4), 301 (2010).CrossRefGoogle Scholar
Xu, Z., Tang, G., Ding, F., Tian, S., and Tian, H.: The effect of multiple pulse treatment on the recrystallization behavior of Mg–3Al–1Zn alloy strip. Appl. Phys. A: Mater. Sci. Process. 88(2), 429 (2007).CrossRefGoogle Scholar
Jiang, Y., Tang, G., Shek, C., Xie, J., Xu, Z., and Zhang, Z.: Mechanism of electropulsing induced recrystallization in a cold-rolled Mg–9Al–1Zn alloy. J. Alloys Compd. 536, 94 (2012).CrossRefGoogle Scholar
Ye, X., Zion, T.H., Tang, G., Geng, Y., and Song, G.: Influence of electropulsing globularization on the microstructure and mechanical properties of Ti–6Al–4V alloy strip with lamellar microstructure. Mater. Sci. Eng., A 622, 1 (2015).CrossRefGoogle Scholar
Ye, X., Tse, Z.T.H., Tang, G., and Song, G.: Mechanical properties and phase transition of biomedical titanium alloy strips with initial quasi-single phase state under high-energy electropulses. J. Mech. Behav. Biomed. Mater. 42, 100 (2015).CrossRefGoogle ScholarPubMed
Wang, H., Chen, L., Liu, D., Song, G., and Tang, G.: Study on electropulsing assisted turning process for AISI 304 stainless steel. Mater. Sci. Technol. 31(13a), 1564 (2015).CrossRefGoogle Scholar
Zhu, Y.H., To, S., Lee, W.B., Liu, X.M., Jiang, Y.B., and Tang, G.Y.: Effects of dynamic electropulsing on microstructure and elongation of a Zn–Al alloy. Mater. Sci. Eng., A 501(1–2), 125 (2009).CrossRefGoogle Scholar
Zhou, Y., Xiao, S., and Guo, J.: Recrystallized microstructure in cold worked brass produced by electropulsing treatment. Mater. Lett. 58(12–13), 1948 (2004).CrossRefGoogle Scholar
Zhu, R.F., Liu, J.N., Tang, G.Y., Shi, S.Q., and Fu, M.W.: Properties, microstructure and texture evolution of cold rolled Cu strips under electropulsing treatment. J. Alloys Compd. 544, 203 (2012).CrossRefGoogle Scholar
Qin, R. and Su, S.: Thermodynamics of crack healing under electropulsing. J. Mater. Res. 17(08), 2048 (2002).CrossRefGoogle Scholar