Hostname: page-component-78c5997874-fbnjt Total loading time: 0 Render date: 2024-11-03T08:35:01.309Z Has data issue: false hasContentIssue false

Evolution of crystallographic texture during deformation of submicron grain size titanium

Published online by Cambridge University Press:  11 February 2011

N.P. Gurao
Affiliation:
Department of Materials Engineering, Indian Institute of Science, Bangalore, 560012, India
Satyam Suwas*
Affiliation:
Department of Materials Engineering, Indian Institute of Science, Bangalore, 560012, India
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Evolution of deformation texture in commercially pure titanium with submicron grain size (SMG) was studied using x-ray diffraction (XRD) and electron back scatter diffraction (EBSD) methods. The material was deformed by rolling at room temperature. The deformation mechanism was found to be slip dominated with a pyramidal <c + a> slip system facilitating plastic deformation. No evidence of tensile or compressive twinning was detected, as generally seen in the case of titanium with conventional microcrystalline grain size. The absence of twinning and the propensity of the pyramidal <c + a> slip system in the SMG Ti is attributed to the lack of coordinated motion of zonal partial dislocations that leads to twinning.

Type
Articles
Copyright
Copyright © Materials Research Society 2011

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Valiev, R.Z., Islamgaliev, R.K., and Alexandrov, I.V.: Bulk nanostructured materials from severe plastic deformation. Prog. Mater. Sci. 45, 103 (2000).CrossRefGoogle Scholar
2.Christian, J.W. and Mahajan, S.: Deformation twinning. Prog. Mater. Sci. 39, 1 (1995).CrossRefGoogle Scholar
3.Noorbaksh, S. and O’Brien, T.D.: Texture formation and transition in cold rolled titanium. Mater. Sci. Eng. 100, 109 (1988).CrossRefGoogle Scholar
4.Hanson, B.H.: Present and future uses of titanium in engineering. Mater. Des. 7, 301 (1986).CrossRefGoogle Scholar
5.Gottstein, G.: Physical Foundation of Materials Science (Springer-Verlag, Berlin, 2006).Google Scholar
6.Partridge, P.G.: The crystallography and deformation of hexagonal close-packed metals. Metall. Rev. 12, 169 (1967).CrossRefGoogle Scholar
7.Lee, H.P., Esling, C.S., and Bunge, H.J.: Development of the rolling texture in titanium. Textures Microstruct. 7, 317 (1988).CrossRefGoogle Scholar
8.Chun, Y.B., Yu, S.H., Semiatin, S.L., and Hwang, S.K.: Effect of deformation twinning on microstructure and texture evolution during cold rolling of CP-titanium. Mater. Sci. Eng., A 398, 209 (2005).CrossRefGoogle Scholar
9.Zhong, Y., Yin, F., and Nagai, K.: Role of deformation twin on texture evolution in cold rolled commercially-pure titanium. J. Mater. Res. 23, 2954 (2008).CrossRefGoogle Scholar
10.Stolyarov, V.V., Zhu, Y.T., Alexandrov, I.V., Lowe, T.C., and Valev, R.Z.: Grain refinement and properties of pure Ti processed by warm ECAP and cold rolling. Mater. Sci. Eng., A 343, 43 (2003).CrossRefGoogle Scholar
11.Salishchev, G.A. and Yu Mironov, S.: Effect of grain size on mechanical properties of commercially-pure titanium. Russ. Phys. J. 44, 596 (2001).CrossRefGoogle Scholar
12.Kim, W.J., Yoo, S.J., and Lee, J.B.: Microstructure and mechanical properties of pure Ti processed by high-ratio differential speed rolling at room temperature. Scr. Mater. 62, 451 (2010).CrossRefGoogle Scholar
13.Suwas, S., Beausir, B., Toth, L.S., Fundenberger, J.J., and Gottstein, G.: Microstructure and texture evolution during ECAP of commercially-pure titanium. Acta Mater. 59, 1121 (2011).CrossRefGoogle Scholar
14.Pawlik, K.: Determination of the orientation. Distribution function from pole figures in arbitrarily defined cells. Phys. Status Solidi B 134, 477 (1986).CrossRefGoogle Scholar
15.Philippe, M.J.: Texture formation in hexagonal materials. Mater. Sci. Forum 157162, 1337 (1994).CrossRefGoogle Scholar
16.Singh, A.K. and Schwarzer, R.: Texture and anisotropy of mechanical properties in titanium and its alloys. Z. Metallkd. 91, 702 (2000).Google Scholar
17.Bunge, H.J.: Texture Analysis in Materials Science—Mathematical Methods, (Butterworth, London, 1982).Google Scholar
18.Zhong, Y., Yin, F., Sakaguchi, T., Nagai, K., and Yang, K.: Dislocation structure evolution and characterization in the compression deformed Mn–Cu alloy. Acta Mater. 55, 2747 (2007).CrossRefGoogle Scholar
19.Inagaki, H.: Texture and mechanical anisotropy in cold-rolled and annealed pure Ti sheets. Z. Metallkd. 83, 40 (1992).Google Scholar
20.Myshlyeav, M.M. and Mironov, S.Y.: Evolution of dislocation boundaries during cold deformation of microcrystalline titanium. Phys. Solid State 44, 738 (2002).Google Scholar
21.Meyers, M.A., Vohringer, O., and Lubarda, V.A.: The onset of twinning in metals: A constitutive description. Acta Mater. 49, 4025 (2001).CrossRefGoogle Scholar
22.El-Danaf, E., Kalidindi, S.R., and Doherty, R.D.: Strain hardening due to deformation twinning in titanium: Mechanisms. Metall. Mater. Trans. A 30, 1223 (1999).CrossRefGoogle Scholar
23.Yu, Q., Shan, Z.-W., . Li, J., Huang, X., Xiao, L., Sun, J., and Ma, E.: Strong crystal size effect on deformation twinning. Nature 463, 335 (2010).CrossRefGoogle ScholarPubMed
24.Wang, J., Hirth, J.P., and Tome, C.N.: { 012} Twinning nucleation mechanisms in hexagonal-close-packed crystals. Acta Mater. 57, 5521 (2009).CrossRefGoogle Scholar
25.Shan, Z-W., Mishra, R.K., Syed Asif, S.A., Warren, O.L., and Minor, A.M.: Mechanical annealing and source-limited deformation in submicrometre-diameter Ni crystals. Nat. Mater. 7, 115 (2007).CrossRefGoogle ScholarPubMed
26.Gurao, N.P. and Suwas, S.: Deformation mechanisms during large strain deformation of nanocrystalline nickel. Appl. Phys. Lett. 94, 191902 (2009).CrossRefGoogle Scholar