Hostname: page-component-586b7cd67f-t8hqh Total loading time: 0 Render date: 2024-11-24T13:27:16.808Z Has data issue: false hasContentIssue false
  • English
  • Français

Enhanced properties of Cu/Sn alloy matrix composites reinforced with β-silicon nitride whiskers

Published online by Cambridge University Press:  12 March 2014

Jinwei Yin ,
Yuping Zeng ,
Dongxu Yao ,
Yongfeng Xia  and
Kaihui Zuo
Jinwei Yin*
Affiliation:
State Key Laboratory of High Performance Ceramics and Superfine Microstructure, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Graduate School of Chinese Academy of Sciences, China
Yuping Zeng*
Affiliation:
State Key Laboratory of High Performance Ceramics and Superfine Microstructure, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Graduate School of Chinese Academy of Sciences, China
Dongxu Yao
Affiliation:
State Key Laboratory of High Performance Ceramics and Superfine Microstructure, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Graduate School of Chinese Academy of Sciences, China
Yongfeng Xia
Affiliation:
State Key Laboratory of High Performance Ceramics and Superfine Microstructure, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Graduate School of Chinese Academy of Sciences, China
Kaihui Zuo
Affiliation:
State Key Laboratory of High Performance Ceramics and Superfine Microstructure, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Graduate School of Chinese Academy of Sciences, China
*
a)Address all correspondence to these authors. e-mail: [email protected]
Get access

Abstract

Cu/Sn alloy matrix composites reinforced with β-Si3N4 whiskers (β-Si3N4w/Cu/Sn) were prepared by powder metallurgy method with the aim of improving the mechanical property. Although the β-Si3N4 whisker additions played a side effect on the densification of the composites, the mechanical property was significantly improved. The highest bending strength of β-Si3N4w/Cu/Sn reached up to 353 MPa, and the highest hardness of composites was also improved to 97.13 HRF. β-Si3N4 whiskers could induce the improved work of fracture and grain refinement of composites and thus brought about the enhancement of mechanical performance. However, excessively high β-Si3N4 whisker content was not beneficial to the high mechanical property because of the low densification and the severe aggregation of whiskers. The β-Si3N4w/Cu/Sn still had a quite high thermal conductivity. As a result, the β-Si3N4w/Cu/Sn could be a promising material applied in a severe environment.

Keywords

compositesstrengthhardness
Type
Articles
Information
Journal of Materials Research , Volume 29 , Issue 6 , 28 March 2014 , pp. 770 - 777
Copyright
Copyright © Materials Research Society 2014 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Lu, Y.A., Yang, J.F., Lu, W.Z., Liu, R.Z., Qiao, G.J., and Bao, C.G.: The mechanical properties of co-continuous Si3N4/Al composites manufactured by squeeze casting. Mater. Sci. Eng., A 527(23), 6289 (2010).CrossRefGoogle Scholar
Hao, S. and Xie, J.: Tensile properties and strengthening mechanisms of SiCp-reinforced aluminum matrix composites as a function of relative particle size ratio. J. Mater. Res. 28(15), 2047 (2013).CrossRefGoogle Scholar
Krishnamurthy, S., Matikas, T.E., and Karpur, P.: Role of matrix microstructure in the ultrasonic characterization of fiber-reinforced metal matrix composites. J. Mater. Res. 12(3), 754 (1997).CrossRefGoogle Scholar
Ferkel, H.: Properties of copper reinforced by laser-generated Al2O3-nanoparticles. Nanostruct. Mater. 11(5), 595 (1999).CrossRefGoogle Scholar
Shehata, F., Fathy, A., Abdelhameed, M., and Moustafa, S.F.: Preparation and properties of Al2O3 nanoparticle reinforced copper matrix composites by in situ processing. Mater. Des. 30(7), 2756 (2009).CrossRefGoogle Scholar
Xue, Z.W., Wang, L.D., Liu, Z., and Fei, W.D.: Effect of interfacial state on thermal expansion behaviors of beta-LiAlSiO4 particulate-reinforced Cu composites. Scr. Mater. 62(11), 867 (2010).CrossRefGoogle Scholar
Tu, J.P., Wang, N.Y., Yang, Y.Z., Qi, W.X., Liu, F., Zhang, X.B., Lu, H.M., and Liu, M.S.: Preparation and properties of TiB2 nanoparticle reinforced copper matrix composites by in situ processing. Mater. Lett. 52(6), 448 (2002).CrossRefGoogle Scholar
Zhan, Y.Z. and Zhang, G.D.: The effect of interfacial modifying on the mechanical and wear properties of SiCp/Cu composites. Mater. Lett. 57(29), 4583 (2003).10.1016/S0167-577X(03)00365-3CrossRefGoogle Scholar
Wan, Y.Z., Wang, Y.L., Luo, H.L., Dong, X.H., and Cheng, G.X.: Effects of fiber volume fraction, hot pressing parameters and alloying elements on tensile strength of carbon fiber reinforced copper matrix composite prepared by continuous three-step electrodeposition. Mater. Sci. Eng., A 288(1), 26 (2000).CrossRefGoogle Scholar
Zhu, Z., Kuang, X., Carotenuto, G., and Nicolais, L.: Fabrication and properties of carbon fibre-reinforced copper composite by controlled three-step electrodeposition. J. Mater. Sci. 32(4), 1061 (1997).CrossRefGoogle Scholar
Li, J., Xia, C., Zhang, Y., Wang, M., and Wang, H.: Effects of TiO2 coating on microstructure and mechanical properties of magnesium matrix composite reinforced with Mg2B2O5w. Mater. Des. 39(0), 334 (2012).CrossRefGoogle Scholar
Zhou, Y., Yu, Z., Zhao, N., Shi, C., Liu, E., Du, X., and He, C.: Microstructure and properties of in situ generated MgAl2O4 spinel whisker reinforced aluminum matrix composites. Mater. Des. 46(0), 724 (2013).CrossRefGoogle Scholar
Zhu, X.W. and Sakka, Y.: Textured silicon nitride: Processing and anisotropic properties. Sci. Technol. Adv. Mater. 9(3), (2008).CrossRefGoogle ScholarPubMed
Hirao, K., Nagaoka, T., Brito, M.E., and Kanzaki, S.: Microstructure control of silicon nitride by seeding with rodlike β-silicon nitride particles. J. Am. Ceram. Soc. 77(7), 1857 (1994).CrossRefGoogle Scholar
Hirosaki, N., Ogata, S., Kocer, C., Kitagawa, H., and Nakamura, Y.: Molecular dynamics calculation of the ideal thermal conductivity of single-crystal α- and β-Si3N4. Phys. Rev. B 65(13), 134110 (2002).CrossRefGoogle Scholar
Kennedy, A.R., Karantzalis, A.E., and Wyatt, S.M.: The microstructure and mechanical properties of TiC and TiB2-reinforced cast metal matrix composites. J. Mater. Sci. 34(5), 933 (1999).CrossRefGoogle Scholar
Kaftelen, H., Unlu, N., Goller, G., Ovecoglu, M.L., and Henein, H.: Comparative processing-structure-property studies of Al-Cu matrix composites reinforced with TiC particulates. Composites Part A 42(7), 812 (2011).10.1016/j.compositesa.2011.03.016CrossRefGoogle Scholar
Chu, K., Liu, Z., Jia, C., Chen, H., Liang, X., Gao, W., Tian, W., and Guo, H.: Thermal conductivity of SPS consolidated Cu/diamond composites with Cr-coated diamond particles. J. Alloys Compd. 490(1–2), 453 (2010).CrossRefGoogle Scholar
Cho, S., Kikuchi, K., Miyazaki, T., Takagi, K., Kawasaki, A., and Tsukada, T.: Multiwalled carbon nanotubes as a contributing reinforcement phase for the improvement of thermal conductivity in copper matrix composites. Scr. Mater. 63(4), 375 (2010).CrossRefGoogle Scholar
Yih, P. and Chung, D.D.L.: Brass-matrix silicon carbide whisker composites prepared by powder metallurgy. J. Mater. Sci. 34(2), 359 (1999).CrossRefGoogle Scholar
Oh, S.Y., Cornie, J.A., and Russell, K.C.: Wetting of ceramic particles with liquid aluminum-alloys. 2. Study of wettability. Metall. Trans. A 20(3), 533 (1989).CrossRefGoogle Scholar
Wang, Z., Song, M., Sun, C., and He, Y.: Effects of particle size and distribution on the mechanical properties of SiC reinforced Al–Cu alloy composites. Mater. Sci. Eng., A 528(3), 1131 (2011).CrossRefGoogle Scholar
Arsenault, R.J., Wang, L., and Feng, C.R.: Strengthening of composites due to microstructural changes in the matrix. Acta Metall. Mater. 39(1), 47 (1991).CrossRefGoogle Scholar
Conlon, K.T. and Wilkinson, D.S.: Effect of particle distribution on deformation and damage of two-phase alloys. Mater. Sci. Eng., A 317(1–2), 108 (2001).CrossRefGoogle Scholar
Prangnell, P.B., Barnes, S.J., Roberts, S.M., and Withers, P.J.: The effect of particle distribution on damage formation in particulate reinforced metal matrix composites deformed in compression. Mater. Sci. Eng., A 220(1–2), 41 (1996).CrossRefGoogle Scholar