Hostname: page-component-586b7cd67f-2brh9 Total loading time: 0 Render date: 2024-11-24T16:47:03.919Z Has data issue: false hasContentIssue false
  • English
  • Français

Enhanced mechanical properties in ultrafine grained 7075 Al alloy

Published online by Cambridge University Press:  03 March 2011

Y.H. Zhao ,
X.Z. Liao ,
Y.T. Zhu  and
R.Z. Valiev
Y.H. Zhao
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545
X.Z. Liao
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545
Y.T. Zhu*
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545
R.Z. Valiev
Affiliation:
Institute of Physics of Advanced Materials, Ufa State Aviation Technical University, 450000 Ufa, Russian Federation
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Highest strength for 7075 Al alloy was obtained by combining the equal-channel-angular pressing (ECAP) and natural aging processes. The tensile yield strength and ultimate strength of the ECAP processed and naturally aged sample were 103% and 35% higher, respectively, than those of the coarse-grained 7075 Al alloy counterpart. The enhanced strength resulted from high densities of Guinier–Preston (G-P) zones and dislocations. This study shows that severe plastic deformation has the potential to significantly enhance the mechanical properties of precipitate hardening 7000 series Al alloys.

Keywords

AlloyCold workingMechanical properties
Type
Rapid Communications
Information
Journal of Materials Research , Volume 20 , Issue 2 , February 2005 , pp. 288 - 291
Copyright
Copyright © Materials Research Society 2005

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Smith, W.F. and Grant, N.J.: The effect of multi-step aging on the strength properties and precipitate-free zone widths in Al-Zn-Mg alloys. Metall. Trans. 1, 979 (1970).CrossRefGoogle Scholar
2.Kelly, A. and Nicholson, R.B.: Precipitate hardening. Prog. Mater. Sci. 10, 216 (1963).Google Scholar
3.Thomas, G. and Nutting, J.: The aging characteristics of aluminum alloys. J. Inst. Met. 88, 81 (1959).Google Scholar
4.Embury, J.D. and Nicholson, R.B.: The nucleation of precipitates: The system Al-Zn-Mg. Acta Metall. 13, 403 (1965).CrossRefGoogle Scholar
5.Smith, W.F.: Structure and Properties of Engineering Alloys (McGraw-Hill, New York, 1993), Chap. 5–9, pp. 209–215.Google Scholar
6.Valiev, R.Z., Islamgaliev, R.K., and Alexandrov, I.V.: Bulk nanostructured materials from severe plastic deformation. Prog. Mater. Sci. 45, 103 (2000).CrossRefGoogle Scholar
7.Zhu, Y.T., and Lowe, T.C.: Observations and issues on mechanisms of grain refinement during ECAP process. Mater. Sci. Eng. A291, 46 (2000).CrossRefGoogle Scholar
8.Iwahashi, Y., Wang, J., Horita, Z., Memoto, M., and Langdon, T.G.: Principle of equal-channel angular pressing for the processing of ultra-fine grained materials. Scripta Mater. 35, 143 (1996).CrossRefGoogle Scholar
9.Morris, D.G. and Munoz-Morris, M.A.: Microstructure of severely deformed Al-3Mg and its evolution during annealing. Acta Mater. 50, 4047 (2002).CrossRefGoogle Scholar
10.Wang, J., Iwahashi, Y., Horita, Z., Furukawa, M., Nemoto, M., Valiev, R.Z., and Langdon, T.G.: An investigation of microstructural stability in an Al-Mg alloy with submicrometer grain size. Acta Mater. 44, 2973 (1996).CrossRefGoogle Scholar
11.Zhao, Y.H., Zhang, K., and Lu, K.: Structure characteristics of nanocrystalline element selenium with different grain sizes. Phys. Rev. B. 56, 14322 (1997).CrossRefGoogle Scholar
12.Ungar, T.: The meaning of size obtained from broadened x-ray diffraction peaks. Adv. Eng. Mater. 5, 323 (2003).CrossRefGoogle Scholar
13.Gubicza, J., Dragomir, I.C., Ribarik, G., Zhu, Y.T., Valiev, R.Z., and Ungar, T.: Characterization of the microstructures of severely deformed titanium by x-ray diffraction profile analysis. Mater. Sci. Forum. 229, 414 (2003).Google Scholar
14.Zhao, Y.H., Sheng, H.W., and Lu, K.: Microstructure evolution and thermal properties in nanocrystalline Fe during mechanical attrition. Acta Mater. 49, 365 (2001).CrossRefGoogle Scholar
15.Zhao, Y.H., Zhang, K., and Lu, K.: Microstructure evolution and thermal properties in nanocrystalline Cu during mechanical attrition. Phys. Rev. B. 66, 085404 (2002).CrossRefGoogle Scholar
16.Zhao, Y.H., Liao, X.Z., Jin, J., Valiev, R.Z., and Zhu, Y.T.: In Ultrafine-Grained Materials III, edited by Zhu, Y.T., Langdon, T.G., Valiev, R.Z., Semiatin, S.L., Sin, D.H., and Lowe, T.C. (TMS, Warrendale, PA, 2004), p. 511.Google Scholar
17.Di Risso, E., Conserva, M., Gatto, F., and Markus, H.: Thermomechanical treatments on high strength Al-Zn-Mg(-Cu) alloys. Metall. Trans. 4, 1133 (1973).CrossRefGoogle Scholar
18.Consera, M., Nuratti, M., Di Risso, E., and Gatto, F.: Age hardening behavior of TMT processed Al-Zn-Mg-Cu alloy. Mater. Sci. Eng. 11, 103 (1973).CrossRefGoogle Scholar
19.Zhao, Y.H., Liao, X.Z., Valiev, R.Z., and Zhu, Y.T.: Structures and mechanical properties of ECAP processed 7075 Al alloy upon natural aging and T651 treatment, in Nanoscale Materials and Modeling—Relations Among Processing Microstructure and Mechanical Properties, edited by Anderson, P.M., Foecke, T., Misra, A., and Rudd, R.E.. (Mater. Res. Soc. Symp. Proc. 821, Warrendale, PA, 2004), p. 59.Google Scholar
20.Zhao, Y.H., Liao, X.Z., Jin, Z., Valiev, R.Z., and Zhu, Y.T.: Microstructures and mechanical properties of ultrafine grained 7075 Al alloy processed by ECAP and their evolutions during annealing. Acta Mater. 52, 4589 (2004).CrossRefGoogle Scholar