Hostname: page-component-586b7cd67f-dlnhk Total loading time: 0 Render date: 2024-11-28T04:15:49.760Z Has data issue: false hasContentIssue false
  • English
  • Français

Effect of SiCp volume fraction on the microstructure and tensile properties of SiCp/2024 Al-based composites prepared by powder thixoforming

Published online by Cambridge University Press:  30 August 2016

Pubo Li  and
Tijun Chen
Pubo Li*
Affiliation:
State Key Laboratory of Advanced Processing and Recycling of Nonferrous Metals, Lanzhou University of Technology, Lanzhou 730050, China
Tijun Chen*
Affiliation:
State Key Laboratory of Advanced Processing and Recycling of Nonferrous Metals, Lanzhou University of Technology, Lanzhou 730050, China
*
b) e-mail: [email protected]
a) Address all correspondence to these authors. e-mail: [email protected]
Get access

Abstract

A new technology for preparing and forming ceramic particle-reinforced metal matrix composites, powder thixoforming, has been proposed. The effect of the SiCp volume fraction on the microstructure and tensile properties of thixoforged SiCp/2024 Al-based composites was studied. The results indicated that the volume fraction affected the effective liquid fraction, primary particle size and shape, and microstructure compactness. A composite with 10 vol% SiCp had the best comprehensive tensile properties, an ultimate tensile strength of 388 MPa, a yield strength of 295 MPa, and an elongation of 3.8%, representing increases of 29.3 and 33.5%, and a decrease of 63.5%, respectively, compared with the values for the thixoforged 2024 Al matrix alloy. During tensile testing, cracks were initiated in the secondary solidified structures, the debonded SiC/Al interface, and the cracked SiCp. For composites containing over 10 vol% SiCp, agglomerated SiCp acted as additional zones of crack initiation.

Keywords

powder processingcompositefracture
Type
Articles
Information
Journal of Materials Research , Volume 31 , Issue 18: Focus Section: Reinventing Boron Chemistry for the 21st Century , 28 September 2016 , pp. 2850 - 2862
Check for updates
Copyright
Copyright © Materials Research Society 2016 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Ted Guo, M.L. and Tsao, C-Y.A.: Tribological behavior of self-lubricating aluminium/SiC/graphite hybrid composites synthesized by the semi-solid powder-densification method. Compos. Sci. Technol. 60(1), 65 (2000).Google Scholar
Slipenyuk, A., Kuprin, V., Milman, Y., Goncharuk, V., and Eckert, J.: Properties of P/M processed particle reinforced metal matrix composites specified by reinforcement concentration and matrix-to-reinforcement particle size ratio. Acta Mater. 54(1), 157 (2006).CrossRefGoogle Scholar
Cheng, N.P., Zeng, S.M., and Liu, Z.Y.: Preparation, microstructures and deformation behavior of SiCp/6066Al composites produced by PM route. J. Mater. Process. Technol. 202(1–3), 27 (2008).Google Scholar
Sajjadi, S.A., Ezatpour, H.R., and Torabi Parizi, M.: Comparison of microstructure and mechanical properties of A356 aluminum alloy/Al2O3 composites fabricated by stir and compo-casting processes. Mater. Des. 34, 106 (2012).Google Scholar
Kumai, S., Hu, J., Higo, Y., and Nunomura, S.: Effects of dendrite cell size and particle distribution on the near-threshold fatigue crack growth behaviour of cast Al–SiCp composites. Acta Mater. 44(6), 2249 (1996).CrossRefGoogle Scholar
Borbély, A., Biermann, H., and Hartmann, O.: FE investigation of the effect of particle distribution on the uniaxial stress–strain behaviour of particulate reinforced metal-matrix composites. Mater. Sci. Eng., A 313(1–2), 34 (2001).Google Scholar
Zu, L.J. and Luo, S.J.: Study on the powder mixing and semi-solid extrusion forming process of SiCp/2024Al composites. J. Mater. Process. Technol. 114(3), 189 (2001).Google Scholar
Chen, C.M., Yang, C.C., and Chao, C.G.: Thixocasting of hypereutectic Al–25Si–2.5Cu–1Mg–0.5Mn alloys using densified powder compacts. Mater. Sci. Eng., A 366(1), 183 (2004).Google Scholar
Fan, Z.: Semisolid metal processing. Int. Mater. Rev. 47(2), 49 (2002).CrossRefGoogle Scholar
Li, P.B., Chen, T.J., Zhang, S.Q., and Guan, R.G.: Research on semisolid microstructural evolution of 2024 aluminum alloy prepared by powder thixoforming. Metals 5(2), 547 (2015).Google Scholar
Li, P.B., Chen, T.J., Zhan, S.Q., and Wang, Y.J.: Effects of partial remelting on the microstructure evolution of SiCp/2024p aluminum composites prepared by alloy powder cold pressing. Spec. Cast. Nonferrous Alloys 35(3), 260 (2015).Google Scholar
Li, P.B., Chen, T.J., Ma, Y., Hao, Y., and Guan, R.G.: Microstructural evolution during partial remelting of a 2024 aluminum alloy prepared by cold pressing ball-milled alloy powders. Mater. Trans. 57(2), 91 (2016).Google Scholar
Chen, Y.S., Chen, T.J., Zhang, S.Q., and Li, P.B.: Effects of processing parameters on microstructure and mechanical properties of powder-thixoforged 6061 aluminum alloy. Trans. Nonferrous Met. Soc. China 25(3), 699 (2015).CrossRefGoogle Scholar
Xiong, B.W., Xu, Z.F., Yan, Q.S., Lu, B.P., and Cai, C.C.: Effects of SiC volume fraction and aluminum particulate size on interfacial reactions in SiC nanoparticulate reinforced aluminum matrix composites. J. Alloys Compd. 509(4), 1187 (2011).Google Scholar
Daoud, A.: Microstructure and tensile properties of 2014 Al alloy reinforced with continuous carbon fibers manufactured by gas pressure infiltration. Mater. Sci. Eng., A 391(1–2), 114 (2005).CrossRefGoogle Scholar
Tzimas, E. and Zavaliangos, A.: Evolution of near-equiaxed microstructure in the semisolid state. Mater. Sci. Eng., A 289(1–2), 228 (2000).Google Scholar
Chen, T.J., Wang, R.Q., Ma, Y., and Hao, Y.: Semisolid microstructure evolution of AZ91D magnesium alloy refined by Al–Ti–B. Mater. Res. 14(4), 532 (2011).CrossRefGoogle Scholar
Cai, Y., Tan, M.J., Shen, G.J., and Su, H.Q.: Microstructure and heterogeneous nucleation phenomena in cast SiC particles reinforced magnesium composite. Mater. Sci. Eng., A 282(1–2), 232 (2000).Google Scholar
Chen, T.J., Hao, Y., and Sun, J.: Microstructural evolution of predeformed SiCp/ZA27 composites during partial remelting. Metall. Mater. Trans. A 35(7), 2073 (2004).CrossRefGoogle Scholar
Schaffer, G.B., Hall, B.J., Bonner, S.J., Huo, S.H., and Sercombe, T.B.: The effect of the atmosphere and the role of pore filling on the sintering of aluminium. Acta Mater. 54(1), 131 (2006).Google Scholar
Lee, J.C., Lee, H.I., Ahn, J.P., Shi, Z.l., and Kim, Y.: Modification of the interface in SiC/Al composites. Metall. Mater. Trans. A 31(31), 2361 (2000).Google Scholar
Hong, S-J., Kim, H-M., Huh, D., Suryanarayana, C., and Chun, B.S.: Effect of clustering on the mechanical properties of SiC particulate-reinforced aluminum alloy 2024 metal matrix composites. Mater. Sci. Eng., A 347(1–2), 198 (2003).Google Scholar
Habibnejad-Korayem, M., Mahmudi, R., and Poole, W.J.: Enhanced properties of Mg-based nano-composites reinforced with Al2O3 nano-particles. Mater. Sci. Eng., A 519(1), 198 (2009).Google Scholar
Mazahery, A., Abdizadeh, H., and Baharvandi, H.R.: Development of high-performance A356/nano-Al2O3 composites. Mater. Sci. Eng., A 518(1–2), 61 (2009).Google Scholar
Li, Z.F., Dong, J., Zeng, X.Q., Lu, C., and Ding, W.J.: Influence of Mg17Al12 intermetallic compounds on the hot extruded microstructures and mechanical properties of Mg–9Al–1Zn alloy. Mater. Sci. Eng., A 466(1–2), 134 (2007).Google Scholar
Chen, T.J., Huang, L.K., Huang, X.F., Ma, Y., and Hao, Y.: Effects of reheating temperature and time on microstructure and tensile properties of thixoforged AZ63 magnesium alloy. Mater. Sci. Technol. 30(1), 96 (2014).CrossRefGoogle Scholar
Wu, S.B. and Arsenault, R.J.: The fracture mode in SiC Al composites. Mater. Sci. Eng., A 138(2), 227 (1991).Google Scholar