Hostname: page-component-5cf477f64f-r2nwp Total loading time: 0 Render date: 2025-04-07T12:31:30.942Z Has data issue: false hasContentIssue false
  • English
  • Français

Continuous measurements of load-penetration curves with spherical microindenters and the estimation of mechanical properties

Published online by Cambridge University Press:  31 January 2011

J. Alcalá ,
A. E. Giannakopoulos  and
S. Suresh
J. Alcalá
Affiliation:
Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139
A. E. Giannakopoulos
Affiliation:
Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139
S. Suresh
Affiliation:
Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139
Get access

Abstract

Elastic and plastic properties of metals and Young's modulus of ceramics are determined in the microindentation regime by continuous measurements of load versus depth of penetration with spherical indenters. Calibration procedures, usually applied in nanoindentation experiments, are not needed in the microregime where spherical indenters (rather than sharp indenters with microscopical spherical tips) can be manufactured. As indenters of larger diameters are used, the elastic response of the specimen can be probed during the loading stage of the indentation tests (and not only during unloading, as is the case with nanoindenters). Hence, an accurate determination of Young's modulus can be achieved without a prior knowledge of possible “piling up” or “sinking in” which may occur at the perimeter of the contact area. The contact response of materials is shown to undergo four distinct regions: (i) pre-Hertzian regime, (ii) Hertzian regime, (iii) small-scale plasticity, and (iv) large-scale plasticity. A general methodology for estimation of yield strength and hardening exponent of metals is proposed in the last regime.

Type
Articles
Information
Journal of Materials Research , Volume 13 , Issue 5 , May 1998 , pp. 1390 - 1400
Copyright
Copyright © Materials Research Society 1998

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Timoshenko, S. and Goodier, J. N., Theory of Elasticity (McGraw- Hill, New York, 1951).Google Scholar
2.Yu, W. and Blanchard, J. P., J. Mater. Res. 11, 2358 (1996).CrossRefGoogle Scholar
3.Field, J. S. and Swain, M. V., J. Mater. Res. 8, 297 (1993).CrossRefGoogle Scholar
4.Field, J. S. and Swain, M. V., J. Mater. Res. 10, 101 (1995).CrossRefGoogle Scholar
5.O'Neill, H., Hardness Measurements of Metals and Alloys, 2nd ed. (Chapman Hall Ltd., 1967).Google Scholar
6.Meyer, E., Z. ver. deutshe Ing. 52, 645 (1908).Google Scholar
7.Tabor, D., The Hardness of Metals (Claredon Press, Oxford, 1951).Google Scholar
8.Tabor, D., J. Inst. Metals 79, 1 (1951).Google Scholar
9.Norbury, A. L. and Samuel, T., J. Iron and Steel Inst. 17, 673 (1928).Google Scholar
10.Matthews, J. R., Acta Metall. 28, 311 (1980).CrossRefGoogle Scholar
11.Hill, R., Stor°akers, B., and Zdunek, A. B., Proc. R. Soc. London A 423, 301 (1989).Google Scholar
12.Haggag, F. M., U.S. Patent 4,852,397 (1989).Google Scholar
13.Suresh, S., Alcal’a, J., and Giannakopoulos, A. E., U.S. Patent Application (filed April 1996).Google Scholar
14.Metals Handbook, Properties and Selection of Metals, 8th ed. (ASM, Metals Park, OH, 1961), Vol. 1, p. 662.Google Scholar
15.Suresh, S., Giannakopoulos, A. E., and Alcal’a, J., Acta Mater. 45, 1307 (1997).CrossRefGoogle Scholar
16.Padture, N., J. Am. Ceram. Soc. 77 (2), 519 (1994).CrossRefGoogle Scholar
17.Johnson, K. L., Contact Mechanics (Cambridge University Press, Cambridge, 1985).CrossRefGoogle Scholar
18.Hamilton, G. M. and Goodman, L. E., J. Appl. Mech. 33, 371 (1966).CrossRefGoogle Scholar
19.Datsko, J., Material Properties and Manufacturing Processes (John Wiley & Sons, New York, 1966).Google Scholar
20.The Science of Hardness Testing and its Research Applications, edited by Westbrook, J. H. and Conrad, H. (Am. Soc. for Metals, 1973).Google Scholar
21.Callister, W. D., Materials Science and Engineering: An Introduction, 3rd ed. (John Wiley & Sons, New York, 1994).Google Scholar
22.Williamson, R. L., Rabin, B. H., and Drake, J. T., J. Appl. Phys. 74, 1310 (1993).CrossRefGoogle Scholar