Hostname: page-component-78c5997874-m6dg7 Total loading time: 0 Render date: 2024-11-07T23:06:49.019Z Has data issue: false hasContentIssue false
  • English
  • Français

Chemical vapor deposition of silicon dioxide barrier layers for conductivity enhancement of tin oxide films

Published online by Cambridge University Press:  31 January 2011

Frank B. Ellis Jr.  and
Jim Houghton
Frank B. Ellis Jr.
Affiliation:
Chronar Corporation, P.O. Box 177, Princeton. New Jersey 08542
Jim Houghton
Affiliation:
Chronar Corporation, P.O. Box 177, Princeton. New Jersey 08542
Get access

Abstract

Silicon dioxide for use as a diffusion barrier between soda lime glass and fluorine-doped tin oxide is deposited uniformly by atmospheric chemical vapor deposition from silane. oxygen, and nitrogen using a simple single-slot injector head. With a sufficiently thick silicon dioxide layer, the conductivity of the tin oxide is greatly improved by reducing the diffusion of sodium into the tin oxide as it is deposited between about 500 to 600 °C. Based upon the conductivity of thin lightly doped tin oxide films, it appears that at least 250 nm of silicon dioxide deposited on soda lime glass are required to essentially eliminate the diffusion of sodium into the tin oxide. However, only about 10 nm of silicon dioxide are required to obtain almost the full benefit of 250 nm thick films for moderately doped tin oxide films approximately 500 nm thick, The silicon dioxide deposition process is examined between 350 and 580 °C. The activation energy for the deposition is about 27 kJ/mole. Peak and average film deposition rates greater than 50 nm/sec and 10 nm/sec, respectively, may be obtained. The dependence of the film growth rate on the silane, oxygen, and propylene (an inhibitor) concentration is examined. The deposition rate is found to be limited by the rate of gas-phase reactions. Deposition conditions which yield high silane utilization and good film uniformity are discussed. The origin of undesirable by-product powder is studied. At low silane concentration, powder is mainly formed as the gases cool due to condensation from intermediate species.

Type
Articles
Information
Journal of Materials Research , Volume 4 , Issue 4 , August 1989 , pp. 863 - 872
Copyright
Copyright © Materials Research Society 1989

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1In our earlier unreported work we found that the sodium signal from SIMS analysis was several orders of magnitude larger for tin oxide deposited directly on soda lime glass than for tin oxide deposited on silicon dioxide coated soda lime glass.Google Scholar
2Graham, J., High Temp.-High Pres. 6, 577 (1974).Google Scholar
3Powder generation was always a problem in our earlier unreported work using a Watkins-Johnson five-slot injector head.Google Scholar
4Vasilyeva, L. L., Drozdov, V.N., Repinsky, S.M., and Svitashec, K.K., Thin Solid Films 55, 221 (1978).CrossRefGoogle Scholar
5Ellis, F.B. Jr and Delahoy, A.E., Sol. Energy Mater. 13, 109 (1986).CrossRefGoogle Scholar
6Ellis, F.B. Jr and Gordon, R.G., J. Appl. Phys. 54, 5381 (1983).CrossRefGoogle Scholar
7Winkle, L. W. and Nelson, C. W., Solid State Technol. 24, 123 (1981).Google Scholar
8Kern, W., Schanble, G.I., and Fisher, A. W., RCA Rev. 37, 3 (1976).Google Scholar
9Shibata, M. and Sugawara, K., J. Electrochem. Soc. 122, 155 (1975).CrossRefGoogle Scholar
10Goldsmith, N. and Kern, W., RCA Rev. 28, 153 (1967).Google Scholar