Hostname: page-component-586b7cd67f-t7czq Total loading time: 0 Render date: 2024-11-28T08:03:41.678Z Has data issue: false hasContentIssue false
  • English
  • Français

Chemical and physical characterization of C(N)-doped W–S sputtered films

Published online by Cambridge University Press:  03 March 2011

A. Nossa  and
A. Cavaleiro
A. Nossa
Affiliation:
Escola Superior de Tecnologia e Gestão, Instituto Politécnico da Guarda, Guarda, Portugal
A. Cavaleiro
Affiliation:
Instituto de Ciências e Engenharia de Materiais e Superfícies, Departamento de Engenharia Mecânica, Faculdade de Ciências e Tecnologia da Universidade de Coimbra, Pinhal de Marrocos, 3030 Coimbra, Portugal
Get access

Abstract

The load-bearing capacity of self-lubricating W–S films can be improved by doping with nitrogen or carbon. In this study, the chemical composition, the atomic bonding, the structure, and the surface and cross section morphologies of sputtered W–S–C(N) films were analyzed. The addition of the doping element leads to a progressive broadening of the x-ray diffraction (XRD) peaks indicating a loss of crystallinity. In W–S–N films, amorphous structure could be obtained. In W–S–C films, W–C compounds were detected in conjunction with the hexagonal WS2 phase. For the highest C contents, a nanocomposite structure, including those phases and graphite, was suggested for the film. X-ray photoelectron spectroscopy results showed different types of bonds in the W4f peak in good agreement with the XRD results, i.e., when W–C(N) compounds were indexed W–S, W–C, and W–N bonds are present in the W4f peak. For the highest C content film, the detection of C–C bond in the C1s peak confirmed the formation of graphite.

Keywords

Thin filmLubricantSputtering
Type
Articles
Information
Journal of Materials Research , Volume 19 , Issue 8 , August 2004 , pp. 2356 - 2365
Copyright
Copyright © Materials Research Society 2004

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Fleischauer, P.D.: Fundamental aspects of the electronic structure, materials properties and lubrication performance of sputtered MoS2 films. Thin Solid Films 154, 309 (1987).CrossRefGoogle Scholar
2.Cohen, S.R., Rapoport, L., Ponomarev, E.A., Cohen, H., Tsirlina, T., Tenne, R. and Lévy-Clément, C.: The tribological behavior of type II textured MX2 (M = Mo, X = S, Se) films. Thin Solid Films 324, 190 (1998).CrossRefGoogle Scholar
3.Buck, V.: Preparation and properties of different types of sputtered MoS2 films. Wear 114, 263 (1987).CrossRefGoogle Scholar
4.Bertrand, P.A.: Orientation of rf-sputter-deposited MoS2 films. J. Mat. Res. 4, 180 (1989).CrossRefGoogle Scholar
5.Moser, J., Liao, H. and Lévy, F.: Texture characterisation of sputtered MoS2 thin films by cross-sectional TEM analysis. J. Phys. D: Appl. Phys. 23, 624 (1990).CrossRefGoogle Scholar
6.Regula, M., Ballif, C., Moser, J. and Lévy, F.: Structural, chemical, and electrical characterization of reactively sputtered WSx thin films. Thin Solid Films 280, 67 (1996).CrossRefGoogle Scholar
7.Spalvins, T.: A review of recent advances in solid film lubrication. J. Vac. Sci. Technol. A 5, 212 (1987).CrossRefGoogle Scholar
8.Lince, J.R.: MoS2-xOx solid solutions in thin films produced by rf-sputter-deposition. J. Mater. Res. 5, 218 (1990).CrossRefGoogle Scholar
9.Fleischauer, P.D. and Lince, J.R.: A comparison of oxidation and oxygen substitution in MoS2 solid film lubricants. Tribol. Int. 32, 627 (1999).CrossRefGoogle Scholar
10.Prasad, S.V., Zabinski, J.S. and McDevitt, N.T.: Friction behavior of pulsed laser deposited tungsten disulfide films. Tribol. Trans. 38, 57 (1995).CrossRefGoogle Scholar
11.Prasad, S.V. and Zabinski, J.S.: Super slippery solids. Nature 387, 761 (1997).CrossRefGoogle Scholar
12.Voevodin, A.A. and Zabinski, J.S.: Supertough wear-resistant coatings with “chameleon” surface adaptation. Thin Solid Films 370, 223 (2000).CrossRefGoogle Scholar
13.Voevodin, A.A., Fitz, T.A., Hu, J.J. and Zabinski, J.S.: Nanocomposite tribological coatings with “chamaleon” surface adaptation. J. Vac. Sci. Technol. A 20, 1434 (2002).CrossRefGoogle Scholar
14.Voevodin, A.A., O’Neill, J.P. and Zabinski, J.S.: WC/DLC/WS2 nanocomposite coatings for aerospace tribology. Tribol. Lett. 6, 75 (1999).CrossRefGoogle Scholar
15.Voevodin, A.A., O’Neill, J.P. and Zabinski, J.S.: Nanocomposite tribological coatings for aerospace applications. Surf. Coat. Technol. 116, 36 (1999).CrossRefGoogle Scholar
16.Nossa, A. and Cavaleiro, A.: The influence of the addition of C or N on the wear behaviour of W–S–C/N coatings. Surf. Coat. Technol. 142, 984 (2001).CrossRefGoogle Scholar
17.Nossa, A. and Cavaleiro, A.: Mechanical behaviour of W–S–N and W–S–C sputtered coatings deposited with a Ti interlayer. Surf. Coat. Technol. 163, 552 (2003).CrossRefGoogle Scholar
18.Nossa, A. and Cavaleiro, A.: Characterisation of WSx sputtered films. “Materiais 99–9° Encontro da Sociedade Portuguesa de Materiais” in Proceedings Conference on Materials 1999, 1, 1 (1999).Google Scholar
19.Dimigen, H., Hübsch, H., Willich, P. and Reichelt, K.: Stoichiometry and friction properties of sputtered MoSx layers. Thin Solid Films 129, 79 (1985).CrossRefGoogle Scholar
20.Hilton, M.R. and Fleischauer, P.D.: TEM lattice imaging of the nanostructure of early-growth sputter-deposited MoS2 solid lubricant films. J. Mater. Res. 5, 406 (1990).CrossRefGoogle Scholar
21.Lévy, F. and Moser, J.: High-resolution cross-sectional studies and properties of molybdenite coatings. Surf. Coat. Technol. 68, 433 (1994).CrossRefGoogle Scholar
22.Fleischauer, P.D., Hilton, M.R., and Bauer, R.: Effects of microstructure and adhesion on performance of sputter-deposited MoS2 solid lubricant coatings. Mechanics of Coatings, Tribology Series 17, paper V (i) 121 (1990).Google Scholar
23.Bichsel, R., Buffat, P. and Lévy, F.: Correlation between process conditions, chemical composition and morphology of MoS2 films prepared by RF planar magnetron sputtering. J. Phys. D: Appl. Phys. 19, 1575 (1986).CrossRefGoogle Scholar
24.Buck, V.: Structure and density of sputtered MoS2-films. Vacuum 36, 89 (1986).CrossRefGoogle Scholar
25.Moser, J. and Lévy, F.: Growth mechanisms and near-interface structure in relation to orientation of MoS2 sputtered films. J. Mater. Res. 7, 734 (1992).CrossRefGoogle Scholar
26.Castanho, J.M. and Vieira, M.T.: The influence of the interstitial element on tribological behaviour of tungsten coatings. Surf. Coat. Technol. 102, 50 (1998).CrossRefGoogle Scholar
27.Cavaleiro, A., Trindade, B. and Vieira, M.T.: Deposition and characterization of fine-grained W–Ni–C/N ternary films. Surf. Coat. Technol. 116, 944 (1999).CrossRefGoogle Scholar
28.Louro, C. and Cavaleiro, A.: Hardness versus structure in W–Si–N sputtered coatings. Surf. Coat. Technol. 116, 74 (1999).CrossRefGoogle Scholar
29.Martin-Litas, I., Vinatier, P., Levasseur, A., Dupin, J.C., Gonbeau, D. and Weill, F.: Characterisation of r.f. sputtered tungsten disulfide and oxysulfide thin films. Thin Solid Films 416, 1 (2002).CrossRefGoogle Scholar
30.Nossa, A., Cavaleiro, A., Carvalho, N.J.M., Kooi, B.J. and De Hosson, J.Th.M. On the microstructure of tungsten disulfide films doped with carbon and nitrogen. (unpublished).Google Scholar
31.Niederhofer, A., Nesladek, P., Mannling, H.D., Moto, K., Veprek, S. and Jilek, M.: Structural properties, internal stress and thermal stability of nc-TiN/a-Si3N4, nc-TiN/TiSix and nc-(Ti1- yAlySix)N superhard nanocomposite coatings reaching the hardness of diamond. Surf. Coat. Technol. 120, 173 (1999).CrossRefGoogle Scholar
32.Raynor, G.V. and Rivlin, V.G. in Phase Equilibria in Iron Ternary Alloys, ed. (The Institute of Metals, London, UK, 1988), p. 26.Google Scholar
33.Cavaleiro, A., Vieira, M.T. and Lemperiere, G.: The structure of thin films deposited from a sintered tungsten carbide with a high cobalt content (15 wt%). Thin Solid Films 185, 199 (1990).CrossRefGoogle Scholar
34.Voevodin, A.A., O’Neill, J., Prasad, S.V. and Zabinski, J.S.: Nanocrystalline WC and WC/a-C composite coatings produced from intersected plasma fluxes at low deposition temperatures. J. Vac. Sci. Technol. A 17, 986 (1999).CrossRefGoogle Scholar
35. International Center for Diffraction Data (ICDD) Cards 41-1487 and 75-1621, PA.Google Scholar
36.Mogne, T. Le, Donnet, C., Martin, J.M., Tonck, A., Millard-Pinard, N., Fayeulle, S. and Mancoffre, N.: Nature of super-lubricating MoS2 physical vapor deposition coatings. J. Vac. Sci. Technol. A 12, 1998 (1994).Google Scholar
37.Wagner, C.D., Riggs, W.H., David, C.E., Moulder, J.F. and Muilenberg, G.E. in Handbook of X-ray Photoelectron Spectroscopy, ed. (Perkin-Elmer Corporation, Physical Electronics Division, Eden Prarie, MN, 1979).Google Scholar
38.http://srdata.nist.gov/xps/main_search_menu.htmGoogle Scholar
39.Bernede, J.C.: About the preferential sputtering of chalcogen from transition metal dichalcogenide compounds and the determination of compound stoichiometry from XPS peak positions. Appl. Surf. Sci. 171, 15 (2001).CrossRefGoogle Scholar
40.Li, S.J., Bernede, J.C., Pouzet, J. and Ny, R. Le: Thick (δ ≥ 300 nm) WS2 films obtained on unpolished glass substrates. Mater. Chem. Phys. 48, 124 (1997).CrossRefGoogle Scholar
41.Louro, C., Cavaleiro, A. and Montemor, F.: How is the chemical bonding of W–Si–N sputtered coatings? Surf. Coat. Technol. 142, 964 (2001).CrossRefGoogle Scholar
42.Zabinski, J.S., Donley, M.S., Prasad, S.V. and McDevitt, N.T.: Synthesis and characterization of tungsten disulphide films grown by pulsed-laser deposition. J. Mater. Sci. 29, 4834 (1994).CrossRefGoogle Scholar