Hostname: page-component-586b7cd67f-2plfb Total loading time: 0 Render date: 2024-12-01T07:17:39.722Z Has data issue: false hasContentIssue false
  • English
  • Français

Can indentation technique measure unique elastoplastic properties?

Published online by Cambridge University Press:  31 January 2011

Ling Liu ,
Nagahisa Ogasawara ,
Norimasa Chiba  and
Xi Chen
Ling Liu
Affiliation:
Department of Civil Engineering and Engineering Mechanics, Columbia University, New York, New York 10027-6699
Nagahisa Ogasawara
Affiliation:
Department of Civil Engineering and Engineering Mechanics, Columbia University, New York, New York 10027-6699
Norimasa Chiba
Affiliation:
Department of Mechanical Engineering, National Defense Academy, Hashirimizu, Yokosuka 239, Japan
Xi Chen*
Affiliation:
Department of Civil Engineering and Engineering Mechanics, Columbia University, New York, New York 10027-6699
*
a) Address all correspondence to this author.e-mail: [email protected]
Get access

Abstract

Indentation is widely used to extract material elastoplastic properties from measured force-displacement curves. Many previous studies argued or implied that such a measurement is unique and the whole material stress-strain curve can be measured. Here we show that first, for a given indenter geometry, the indentation test cannot effectively probe material plastic behavior beyond a critical strain, and thus the solution of the reverse analysis of the indentation force-displacement curve is nonunique beyond such a critical strain. Secondly, even within the critical strain, pairs of mystical materials can exist that have essentially identical indentation responses (with differences below the resolution of published indentation techniques) even when the indenter angle is varied over a large range. Thus, fundamental elastoplastic behaviors, such as the yield stress and work hardening properties (functions), cannot be uniquely determined from the force-displacement curves of indentation analyses (including both plural sharp indentation and deep spherical indentation). Explicit algorithms of deriving the mystical materials are established, and we qualitatively correlate the sharp and spherical indentation analyses through the use of critical strain. The theoretical study in this paper addresses important questions of the application range, limitations, and uniqueness of the indentation test, as well as providing useful guidelines to properly use the indentation technique to measure material constitutive properties.

Keywords

HardnessNanoindentation
Type
Articles
Information
Journal of Materials Research , Volume 24 , Issue 3 , March 2009 , pp. 784 - 800
Copyright
Copyright © Materials Research Society 2009

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Cheng, Y.T. and Cheng, C.M.: Scaling, dimensional analysis, and indentation measurements. Mater. Sci. Eng., R 44, 91 (2004).CrossRefGoogle Scholar
2.Gouldstone, A., Chollacoop, N., Dao, M., Li, J., Minor, A.M., and Shen, Y-L.: Indentation across size scales and disciplines: Recent developments in experimentation and modeling. Acta Mater. 55, 4015 (2007).CrossRefGoogle Scholar
3.Cao, G. and Chen, X.: Mechanisms of nanoindentation on single-walled carbon nanotubes: The effect of nanotube length., J. Mater. Res. 21, 1048 (2006).CrossRefGoogle Scholar
4.Chen, X., Xiang, Y., and Vlassak, J.J.: A novel technique to measure mechanical properties of porous materials by nanoindentation. J. Mater. Res. 21, 715 (2006).CrossRefGoogle Scholar
5.Gordon, V., Chen, X., Hutchinson, J.W., Bausch, A.R., Marquez, M., and Weitz, D.A.: Self-assembled inflated polymer membrane capsules by osmotic pressure. J. Am. Chem. Soc. 126, 14117 (2004).CrossRefGoogle ScholarPubMed
6.Zhao, M., Chen, X., Xiang, Y., Vlassak, J.J., Lee, D., Ogasawara, N., Chiba, N., and Gan, Y.X.: Measuring elastoplastic properties of thin films on an elastic substrate using sharp indentation. Acta Mater. 55, 6260 (2007).CrossRefGoogle Scholar
7.Chen, X., Hutchinson, J.W., and Evans, A.G.: Simulation of the high temperature impression of thermal-barrier coatings with columnar microstructure. Acta Mater. 52, 565 (2004).Google Scholar
8.Chen, X., Yan, J., and Karlsson, A.M.: On the determination of residual stress and mechanical properties by indentation. Mater. Sci. Eng., A 416, 139 (2006).CrossRefGoogle Scholar
9.Cheng, Y.T. and Cheng, C.M.: Scaling approach to conical indentation in elastic-plastic solids with work hardening. J. Appl. Phys. 84, 1284 (1998).CrossRefGoogle Scholar
10.Li, M., Chen, W.M., Liang, N.G., and Wang, L.D.: A numerical study of indentation using indenters of different geometry. J. Mater. Res. 18, 73 (2004).Google Scholar
11.Bucaille, J.L., Stauss, S., Felder, E., and Michler, J.: Determination of plastic properties of metals by instrumented indentation using different sharp indenters. Acta Mater. 51, 1663 (2003).CrossRefGoogle Scholar
12.Chollacoop, N., Dao, M., and Suresh, S.: Depth-sensing instrumented indentation with dual sharp indenters. Acta Mater. 51, 3713 (2003 ).Google Scholar
13.Futakawa, M., Wakui, T., Tanabe, Y., and Ioka, I.: Identification of the constitutive equation by the indentation technique using plural indenters with different apex angles. J. Mater. Res. 16, 2283 (2001).CrossRefGoogle Scholar
14.Ogasawara, N., Chiba, N., and Chen, X.: Representative strain of indentation analysis. J. Mater. Res. 20, 2225 (2005).Google Scholar
15.DiCarlo, A., Yang, H.T.Y., and Chandrasekar, S.: Semi-inverse method for predicting stress-strain relationship from cone indentations. J. Mater. Res. 18, 2068 (2003).CrossRefGoogle Scholar
16.Cao, Y.P. and Lu, J.: Depth-sensing instrumented indentation with dual sharp indenters: Stability analysis and corresponding regularization schemes. Acta Mater. 52, 1143 (2004).Google Scholar
17.Ahn, J-H. and Kwon, D.: Derivation of plastic stress—strain relationship from ball indentations: Examination of strain definition and pileup effect. J. Mater. Res. 16, 3170 (2001).Google Scholar
18.Swadener, J.G., Taljat, B., and Pharr, G.M.: Measurement of residual stress by load and depth-sensing indentation with spherical indenters. J. Mater. Res. 16, 2091 (2001).Google Scholar
19.Taljat, B., Zacharia, T., and Kosel, F.: New analytical procedure to determine stress-strain curve from spherical indentation data. Int. J. Solids Struct. 35, 4411 (1998).CrossRefGoogle Scholar
20.Lee, H., Lee, J.H., and Pharr, G.M.: A numerical approach to spherical indentation techniques for material property evaluation. J. Mech. Phys. Solids 53, 2037 (2005).CrossRefGoogle Scholar
21.Cao, Y.P. and Lu, J.: A new method to extract the plastic properties of metal materials from an instrumented spherical indentation loading curve. Acta Mater. 52, 4023 (2004).CrossRefGoogle Scholar
22.Zhao, M., Ogasawara, N., Chiba, N., and Chen, X.: A new approach to measure the elastic-plastic properties of bulk materials using spherical indentation. Acta Mater. 54, 23 (2006).Google Scholar
23.Gao, X.L., Jing, X.N., and Subhash, G.: Two new expanding cavity models for indentation deformations of elastic strain-hardening materials. Int. J. Solids Struct. 43, 2193 (2006).CrossRefGoogle Scholar
24.Chen, X., Hutchinson, J.W., and Evans, A.G.: The mechanics of indentation induced lateral cracking., J. Am. Ceram. Soc. 88, 1233 (2005).Google Scholar
25.Alkorta, J., Martinez-Esnaola, J.M., and Sevillano, J.G.: Absence of one-to-one correspondence between elastoplastic properties and sharp-indentation load-penetration data., J. Mater. Res. 20, 432 (2005).CrossRefGoogle Scholar
26.Tho, K.K., Swaddiwudhipong, S., Liu, Z.S., Zeng, K., and Hua, J.: Uniqueness of reverse analysis from conical indentation tests. J. Mater. Res. 19, 2498 (2004).Google Scholar
27.Ogasawara, N., Zhao, M., Chiba, N., and Chen, X.: Comments on “Extracting the plastic properties of metal materials from micro-indentation tests: Experimental comparison of recently published methods” by Guelorget, B., et al. [J. Mater. Soc. 22, 1512 (2007)]: The correct methods of analyzing experimental data and reverse analysis of indentation tests. J. Mater. Res. 23, 598 (2008).Google Scholar
28.Qian, X., Cao, Y.P., and Lu, J.: Dependence of the representative strain on the hardening functions of metallic materials in indentation. Scr. Mater. 57, 57 (2007).CrossRefGoogle Scholar
29.Oliver, W.C. and Pharr, G.M.: An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments., J. Mater. Res. 7, 1564 (1992).Google Scholar
30.Hay, J.C., Bolshakov, A., and Pharr, G.M.: A critical examination of the fundamental relations used in the analysis of nanoindentation data., J. Mater. Res. 14, 2296 (1999).CrossRefGoogle Scholar
31.King, R.B.: Elastic analysis of some punch problems for a layered medium. Int. J. Solids Struct. 23, 1657 (1987).CrossRefGoogle Scholar
32.Mesarovic, S.D. and Fleck, N.A.: Spherical indentation of elastic-plastic solids. Proc. R. Soc. London, Ser. A 455, 2707 (1999).Google Scholar
33.Ogasawara, N., Chiba, N., and Chen, X.: Limit analysis-based approach to determine the material plastic properties with conical indentation. J. Mater. Res. 21, 947 (2006).CrossRefGoogle Scholar
34.Swaddiwudhiponga, S., Tho, K.K., Liu, Z.S., and Zeng, K.: Material characterization based on dual indenters. Int. J. Solids Struct. 42, 69 (2005).Google Scholar
35.Cao, Y.P. and Huber, N.: Further investigation on the definition of the representative strain in conical indentation. J. Mater. Res. 21, 1810 (2006).Google Scholar
36.Huber, N. and Tsakmakis, C.: Determination of constitutive properties from spherical indentation data using neural networks. Part I: The case of pure kinematic hardening in plasticity laws. J. Mech. Phys. Solids 47, 1569 (1999).CrossRefGoogle Scholar
37.Wang, L. and Rokhlin, S.I.: Universal scaling functions for continuous stiffness nanoindentation with sharp indenters. Int. J. Solids Struct. 42, 3807 (2005).Google Scholar
38.Wang, L., Ganor, M., and Rokhlin, S.I.: Inverse scaling function in nanoindentation with sharp indenters: Determination of material properties. J. Mater. Res. 20, 987 (2005).CrossRefGoogle Scholar
39.Tyulyukovskiy, E. and Huber, N.: Neural networks for tip correction of spherical indentation curves from bulk metals and thin metal films. J. Mech. Phys. Solids 55, 391 (2007).CrossRefGoogle Scholar
40.Ogasawara, N., Chiba, N., and Chen, X.: Measuring the plastic properties of bulk materials by one microindentation test. Scr. Mater. 54, 65 (2006).Google Scholar
41.Casals, O. and Alcala, J.: Analytical and experimental resolutions in the duality of mechanical property extractions from instrumented indentation experiments: Comments on “On determination of material parameters from loading and unloading responses in nanoindentation with a single sharp indenter” by L. Wang and S.I. Rokhlin. J. Mater. Res. 22, 1138 (2007) [J. Mater. Res. 21, 995 (2006)].CrossRefGoogle Scholar
42.Casals, O. and Alcala, J.: The duality in mechanical property extractions from Vickers and Berkovich instrumented indentation experiments. Acta Mater. 53, 3545 (2005).CrossRefGoogle Scholar
43.Luo, J. and Lin, J.: A study on the determination of plastic properties of metals by instrumented indentation using two sharp indenters. Int. J. Solids Struct. 44, 5803 (2007).CrossRefGoogle Scholar
44.Le, M-Q.: A computational study on the instrumented sharp indentations with dual indenters. Int. J. Solids Struct. 45, 2818 (2008).CrossRefGoogle Scholar
45.Lan, H. and Venkatesh, T.A.: Determination of the elastic and plastic properties of materials through instrumented indentation with reduced sensitivity. Acta Mater. 55, 2025 (2007).CrossRefGoogle Scholar
46.Herbert, E.G., Pharr, G.M., Oliver, W.C., Lucas, B.N., and Hay, J.L.: On the measurement of stress-strain curves by spherical indentation. Thin Solid Films 398, 331 (2001).Google Scholar
47.Zhu, T.T., Bushby, A.J., and Dunstan, D.J.: Size effect in the initiation of plasticity for ceramics in nanoindentation. J. Mech. Phys. Solids 56, 1170 (2008).Google Scholar
48.Cheng, Y.T. and Cheng, C.M.: Can stress-strain relationships be obtained from indentation curves using conical and pyramidal indenters?, J. Mater. Res. 14, 3493 (1999).CrossRefGoogle Scholar
49.Pelletier, H., Krier, J., Cornet, A., and Mille, P.: Limits of using bilinear stress-strain curve for finite element modeling of nanoindentation response on bulk materials. Thin Solid Films 379, 147 (2000).CrossRefGoogle Scholar
50.Pelletier, H.: Predictive model to estimate the stress-strain curves of bulk metals using nanoindentation. Tribol. Int. 39, 593 (2006).CrossRefGoogle Scholar
51.Hasanov, A.: An inversion method for identification of elastoplastic properties for engineering materials from limited spherical indentation measurements. Inverse Prob. 15, 601 (2007).CrossRefGoogle Scholar
52.Capehart, T.W. and Cheng, Y-T.: Determining constitutive models from conical indentation: Sensitivity analysis. J. Mater. Res. 18, 827 (2003).Google Scholar
53.Chen, X., Ogasawara, N., Zhao, M., and Chiba, N.: On the uniqueness of measuring elastoplastic properties from indentation: The indistinguishable mystical materials. J. Mech. Phys. Solids 55, 1618 (2007).CrossRefGoogle Scholar
54.Bowden, F.P. and Tabor, D.: The Friction and Lubrication of Solids (Oxford University Press, Oxford, 1950).Google Scholar
55.Guelorget, B., Francois, M., Liu, C., and Lu, J.: Extracting the plastic properties of metal materials from microindentation tests: Experimental comparison of recently published methods. J. Mater. Res. 22, 1512 (2007).Google Scholar
56.Cao, Y.P., Qian, X., and Huber, N.: Spherical indentation into elastoplastic materials: Indentation-response based definitions of the representative strain. Mater. Sci. Eng., A 454–455, 1 (2007).CrossRefGoogle Scholar
57.Ogasawara, N., Chiba, N., Zhao, M., and Chen, X.: Comments on “Further investigation on the definition of the representative strain in conical indentation” by Y. Cao and N. Huber. [J. Mater. Res. 21, 1810 (2006)]. J. Mater. Res. 22, 858 (2007).Google Scholar
58.Ogasawara, N., Chiba, N., Zhao, M., and Chen, X.: Determine material plastic properties with conical indentation: An optimized framework of the representative strain. J. Solid Mech. Mater. Eng. 1, 895 (2007).CrossRefGoogle Scholar
59.Qian, X., Cao, Y., Zhang, J., Raabe, D., Yao, Z., and Fei, B.: An inverse approach to determine the mechanical properties of elastoplastic materials using indentation tests. Computers Materials & Continua 7, 33 (2008).Google Scholar