Hostname: page-component-cd9895bd7-jn8rn Total loading time: 0 Render date: 2024-12-21T01:47:36.471Z Has data issue: false hasContentIssue false
  • English
  • Français

Self-induced flow in a rotating tube

Published online by Cambridge University Press:  26 April 2006

S. Gilham ,
P. C. Ivey ,
J. M. Owen  and
J. R. Pincombe
S. Gilham
Affiliation:
Thermo-Fluid Mechanics Research Centre, School of Engineering and Applied Sciences, University of Sussex, Falmer, Brighton, BN19QT, UK Present address: WS Atkins Engineering Sciences Ltd., Woodcote Grove, Ashley Road, Epsom, Surrey, KT18 5BW, UK.
P. C. Ivey
Affiliation:
Thermo-Fluid Mechanics Research Centre, School of Engineering and Applied Sciences, University of Sussex, Falmer, Brighton, BN19QT, UK Present address: Department of Turbomachinery and Engineering Mechanics, School of Mechanical Engineering, Cranfield Institute of Technology, Cranfield, Beds, MK43 OAL, UK.
J. M. Owen
Affiliation:
Thermo-Fluid Mechanics Research Centre, School of Engineering and Applied Sciences, University of Sussex, Falmer, Brighton, BN19QT, UK Present address: School of Mechanical Engineering, University of Bath, Claverton Down, Bath, BA2 7AY, UK.
J. R. Pincombe
Affiliation:
Thermo-Fluid Mechanics Research Centre, School of Engineering and Applied Sciences, University of Sussex, Falmer, Brighton, BN19QT, UK
Get access Rights & Permissions [Opens in a new window]

Abstract

When a tube, sealed at one end and open to a quiescent environment at the other, is rotated about its axis, fluid flows from the open end along the axis towards the sealed end and returns in an annular boundary layer on the cylindrical wall. This paper describes the first known study to be made of this self-induced flow. Numerical solutions of the Navier–Stokes equations are shown to be in mainly good agreement with experimental results obtained using flow visualization and laser–Doppler anemometry in a rotating glass tube.

The self-induced flow in the tube can be described in terms of the length-to-radius ratio, G, and the Ekman number, E. However, for large values of G (G [ges ] 20), the flow outside the boundary layer on the endwall of the tube can be characterized by a single, modified, Ekman number, E*, where E* = GE. Although most of the fluid entering the open end of the tube is entrained into the annular (Stewartson-type) boundary layer, for small values of E* (E* < 0.2) some flow reaches the sealed end. For this so-called 'short-tube case’, the flow in the boundary layer on the endwall is shown to be similar to that associated with a disk rotating in a quiescent environment: the free disk. The self-induced flow for the short-tube case is believed to be responsible for the ’ hot-poker effect’ used, on some jet engines, to provide ice protection for the nose bullet.

Type
Research Article
Information
Journal of Fluid Mechanics , Volume 230 , September 1991 , pp. 505 - 524
Copyright
© 1991 Cambridge University Press

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Benton, E. R. 1966 On the flow due to a rotating disc. J. Fluid Mech. 24, 781–800.Google Scholar
Brouwers, J. J. H. 1976 On the motion of a compressible fluid in a rotating cylinder. Doctoral thesis, University of Twente.
Cochran, W. G. 1934 The flow due to a rotating disk. Proc. Camb. Phil. Soc. 30, 365–375.Google Scholar
Doormaal, J. P. van & Raithby, G. D. 1984 Enhancements of the SIMPLE method for predicting incompressible fluid flows. Numer. Heat Transfer 7, 147 163.Google Scholar
Ekman, V. W. 1905 On the influence of the earth's rotation on ocean-currents. Ark. Mat. Astr. Fys. 2, 1–52.Google Scholar
Escudier, M. P. 1984 Observations of the flow produced in a cylindrical container by a rotating endwall. Exps Fluids 2, 189–196.Google Scholar
Gilham, S. 1990 Theoretical study of self-induced flow in a rotating tube. D. Phil. thesis, University of Sussex.
Gilham, S., Ivey, P. C. & Owen, J. M. 1991 Self-induced flow in a stepped rotating tube. ASME Intl Gas Turbine Conf., Orlando, Paper 91-GT-276.Google Scholar
Gosman, A. D., Koosinlin, Koosinlin, ockwood, F. C. & Spalding, D. B. 1976 Transfer of heat in rotating systems. ASME Intl Gas Turbine Conf., New Orleans, Paper 76-GT-25.Google Scholar
Ivey, P. C. 1988 Self-induced flow in a rotating tube. D.Phil, thesis, University of Sussex.
KaArmaAn, Th. von 1921 uUber laminare und turbulente Reibung. Z. Angew. Math. Mech. 1, 233–252.Google Scholar
Owen, J. M. & Pincombe, J. R. 1981 Rotationally induced flow and heat transfer in circular tubes, University of Sussex Rep. 81/TFMRC/32. School of Engineering and Applied Sciences, University of Sussex.Google Scholar
Owen, J. M. & Rogers, R. H. 1989 Flow and Heat Transfer in Rotating-Disc Systems. Volume I: Rotor-Stator Systems. Taunton: Research Studies Press.
Patankar, S. V. 1980 Numerical Heat Transfer and Fluid Flow. McGraw-Hill.
Patankar, S. V. & Spalding, D. B. 1972 A calculation procedure for heat and mass transfer in three-dimensional parabolic flows. Intl J. Heat Mass Transfer 15, 1787–1806.Google Scholar
Schlichting, H. 1979 Boundary-Layer Theory. McGraw Hill.
Stewartson, K. 1957 On almost rigid rotations. J. Fluid Mech. 3, 17–26.Google Scholar
vaughan, C. M., Gilham, S. & Chew, J. W. 1989 Numerical solutions of rotating disc flows using a non-linear multigrid algorithm: Proc. 6th Intl Conf. on Numerical Methods in Laminar and Turbulent Flow, vol. 6, pp. 63–73. Swansea: Pineridge.