Hostname: page-component-cd9895bd7-gbm5v Total loading time: 0 Render date: 2024-12-18T08:13:59.295Z Has data issue: false hasContentIssue false
  • English
  • Français

Full integrated process to manufacture RF-MEMS and MMICs on GaN/Si substrate

Published online by Cambridge University Press:  07 July 2010

Flavia Crispoldi ,
Alessio Pantellini ,
Simone Lavanga ,
Antonio Nanni ,
Paolo Romanini ,
Leonardo Rizzi ,
Paola Farinelli  and
Claudio Lanzieri
Flavia Crispoldi
Affiliation:
Consorzio Optel, Via Tagliamento 45, Rome, Italy.
Alessio Pantellini
Affiliation:
SELEX Sistemi Integrati SpA, Via Tiburtina Km. 12,400, Rome 00131, Italy.
Simone Lavanga
Affiliation:
SELEX Sistemi Integrati SpA, Via Tiburtina Km. 12,400, Rome 00131, Italy.
Antonio Nanni
Affiliation:
SELEX Sistemi Integrati SpA, Via Tiburtina Km. 12,400, Rome 00131, Italy.
Paolo Romanini
Affiliation:
SELEX Sistemi Integrati SpA, Via Tiburtina Km. 12,400, Rome 00131, Italy.
Leonardo Rizzi
Affiliation:
Consorzio Optel, Via Tagliamento 45, Rome, Italy.
Paola Farinelli
Affiliation:
Università di Perugia, DIEI, Via G. Duranti 93, Perugia, Italy.
Claudio Lanzieri*
Affiliation:
SELEX Sistemi Integrati SpA, Via Tiburtina Km. 12,400, Rome 00131, Italy.
*
Corresponding author: C. Lanzieri Email: [email protected]
Get access Rights & Permissions [Opens in a new window]

Abstract

Radio Frequency Micro-Electro-Mechanical System (RF-MEMS) represents a feasible solution to obtain very low power dissipation and insertion loss, very high isolation and linearity switch with respect to “solid state” technologies. In this paper, we demonstrate the full integration of RF-MEMS switches in the GaN-HEMT (Gallium Nitride/High Electron Mobility Transistor) fabrication line to develop RF-MEMS devices and LNA-MMIC (Low Noise Amplifier/Monolithic Microwave Integrated Circuit) prototype simultaneously in the same GaN wafer. In particular, two different coplanar wave (CPW) LNAs and a series of discrete RF-MEMS in ohmic-series and capacitive-shunt configuration have been fabricated. RF-MEMS performances reveal an insertion loss and isolation better than 1 and 15 dB, respectively, in the frequency range 20–50 GHz in the case of pure capacitive shunt switches and in the frequency range 5–35 GHz for the ohmic-series switches. Moreover, the GaN HEMT device shows an Fmax of about 38 GHz and a power density of 6.5 W/mm, while for the best LNA-MMIC we have obtained gain better than 12 dB at 6–10 GHz with a noise figure of circa 4 dB, demonstrating the integration achievability.

Keywords

RF-MEMSGaN HEMTGaN MMIC
Type
Original Article
Information
International Journal of Microwave and Wireless Technologies , Volume 2 , Special Issue 3-4: European Microwave Week 2009 , August 2010 , pp. 333 - 339
Copyright
Copyright © Cambridge University Press and the European Microwave Association 2010

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1]Bouchaud, J.; Wicht, H.: RF MEMS: status of the industry and roadmaps, in RadioFrequency integrated Circuits (RFIC) Symp., 2005. Digest of papers, 2005 IEEE 12–14, June (2005), 379–384, Munich, Allemagne.Google Scholar
[2]Pranonsatit, S.; Holmes, A.S.; Robertson, I.D.; Lucyszyn, S.: Single pole eight-throw RF-MEMS rotary switch. J. Microelectromech. Syst., 15(6), (2006), 1735–1744.CrossRefGoogle Scholar
[3]Petersen, K.E. et al. : Micromechanical Membrane Switches on Silicon. IBM J. Res. Dev., 23(4), (1979), 376–385.CrossRefGoogle Scholar
[4]Melle, S. et al. : Reliability-Modeling of Capacitive RF-MEMS; IEEE Trans on Microwave Theory and Techniques. Microelectronics Reliability, 45(9–11), (2005), 1770–1775.Google Scholar
[5]Chiao, J.-C.: MEMS RF devices for antenna applications. Microw. Conf. 2000, Asia–Pacific, December 3–6, 2000, 895–898.Google Scholar
[6]Rebeiz, G.M.: RF MEMS, Theory, Design and Technology, Ed. Wiley Interscience (2003), Hoboken, New Jersey, 5–15.CrossRefGoogle Scholar
[7]Rebeiz, G. M.; Tan, G. L.; Hayden, J.S.: RF MEMS Phase Shifters: Design and Applications. IEEE Microw. Mag., June 2002.CrossRefGoogle Scholar
[8]Chen, S.; Baughn, T.V.; Yao, Z.J.; Goldsmith Charles, L.: A New In Situ Residual Stress Measurement Method for a MEMS thin Fixed-Fixed Beam Structure. J. Microelectromech. Syst., 11(4), 2002, 309–316, Raytheon Syst. Co., Dallas.CrossRefGoogle Scholar
[9]Wang, Z.; Chow, L.; Volakis, J.L.; Saitou, K.; Kurabayashi, K.: Contact physics modeling and optimization design of RF-MEMS cantilever switches, in Antennas Propag. Soc. Int. Symp., 2005 IEEE, 1A (3–8), July 2005, 81–84.Google Scholar
[10]Rottemberg, A.; Jansen, H.; Fiorini, P.; De Raedt, W.; Tilmans, H.: Novel RF-MEMS capacitive switching structures, in Proc. Eur. Microw. Conf. 2002, Milan, Italy, September 24–26 2002, 809–812.Google Scholar
[11]Ciccognani, W. et al. : GaN Device Technology: Manufacturing, Characterization, Modelling and Verification, in Proc. of COMITE 2008, Prague, April 2008, 15–20.Google Scholar
[12]Bettidi, A. et al. : X-Band T/R module in state-of-the-art GaN technology. EuRAD (2009), Rome, 258–261.Google Scholar
[13]Krausse, D.; Quay, R.; Kiefer, R.; Tessmann, A.; Massler, H.; Leuther, A. et al. : Robust GaN HEMT Low-Noise Amplifier MMICs for X-band Applications in 12th GaAs Symp., Amsterdam 2004.Google Scholar
[14]Bettidi, A.; Corsaro, F.; Cetronio, A.; Nanni, A.; Peroni, M.; Romanini, P.: X-Band GaN-HEMT LNA Performance versus Robustness Trade-off, in Proc. of EuMIC09, 2009 Rome, 439–442.CrossRefGoogle Scholar
[15]Crispoldi, F.; Pantellini, A.; Lavanga, S.; Nanni, A.; Romanini, P. et al. : New Fabrication Process to Manufacture RF-MEMS and HEMT on GaNSi Substrate, in Proc. of EuMIC09, 2009 Rome.CrossRefGoogle Scholar