The spray characteristics significantly affected the combustion performance. The injection pressure and fuel properties are factors that affect the spray cone angle, penetration, and droplet distribution. Although substantial research has been conducted on spray attributes, understanding the complex biofuel spray dynamics in real nozzles and injectors is crucial. This study examines hydro-processed esters and fatty acid (HEFA) spray characteristics of used cooking oil and palm oil biodiesel in a constant-volume chamber. The study was performed by varying the injection pressures ranging from 30 to 120psi for pure fuels and Jet A-1 blends. Experiments were conducted at standard sea-level atmospheric pressure and an ambient temperature of ±297K using an airblast fuel injector. The initial fuel temperature was set at ±302K. Jet A-1 was used as the baseline fuel for the comparative analysis. Particle image velocimetry (PIV) was employed to visualise the microscopic and macroscopic characteristics of the fuel spray. The results revealed a progressive increase in the penetration length corresponding to an increase in the injection pressure. Lower pressures yielded non-uniform particle distributions across the spray area, whereas cone angle augmentation stabilised at elevated pressures. A blend of 60% Jet A-1 and 40% HEFA closely matched Jet A-1 characteristics, indicating alternative aviation fuel potential. These real-time insights into spray behaviour are critical for enhancing the fuel efficiency and mitigating the generation of particulate emissions resulting from spray combustion.

A comparison of the modelling methodologies to capture the damage onset and delamination initiation in Abaqus and LS-Dyna is presented. A quasi-isotropic carbon fibre reinforced polymer laminate is modelled under a low-energy impact scenario. Hashin, Puck and Cuntze criteria are implemented for assessing intra-laminar damage in Abaqus in the linear elastic regime without damage evolution, with Virtual Crack Closure Technique being used for inter-laminar failure. In LS-Dyna, the Chang-Chang criterion is used for the intra-lamina failure with damage evolution, whereas delamination is captured using cohesive zone model and the tiebreak contact algorithm. The implementations carried out by both finite element software result in a modelling work well set to analyse and predict the impact response at the initial stages of delamination and damage within the plies. The composite damage criteria used in both finite element codes overall predict stiffer results when compared with the experimental data, however, remain in close agreement with each other.

In this paper, we investigate the constrained attitude control problem of hypersonic vehicles (HVs). An improved prescribed performance dynamic surface control method is proposed based on an adaptive scaling strategy. Because of the uncertain time-varying disturbances, the controlled state may violate the constraint in the prescribed performance control (PPC) framework. An adaptive scaling strategy is introduced in the PPC method to avoid state violation. The performance function is scaled with respect to the state adaptively. Moreover, a nonlinear disturbance observer is used to compensate the sum of external and other internal disturbances of the system. The proposed method improves the system dynamic performance while ensuring the system robustness. Furthermore, the stability of the closed-loop system is proved by Lyapunov analysis. Finally, numerical simulations are implemented to verify the effectiveness of the PPC method and superiority over other methods.

A compressible large eddy simulation (LES) is performed to study a pulsed jet actuator that is used to control a turbulent axisymmetric bluff body wake. The actuator is driven at low-frequency ($f = 200$Hz, $S{t_\theta } = 0.029$) and high amplitude (${C_\mu } = 0.034$). The numerical scheme and a suitable boundary condition for the pulsed jet are validated, showing good agreement with experimental results. A comparison of the velocity boundary condition and the moving boundary condition shows that, in the vicinity of the orifice/slot and in the downstream region, the results from these two methods are identical, while the fluid behaviour inside the cavity shows difference. An analysis of the pulsed jet actuator shows that the phase lag of the cavity pressure is determined by the integration of the diaphragm motion and the pulsed jet. The mean total pressure distribution shows that the total pressure loss is concentrated in the vicinity of the slot. Dynamic mode decomposition (DMD) on the pressure field is used to extract coherent structures which oscillate with the same frequency as that of the diaphragm motion. Some small-scale high-frequency structures are also apparent.

The distinct operational characteristics of military aircraft, relative to civil aircraft, have impeded the standardisation of airworthiness management practice across Europe. Standardisation has been further deterred by the intertwined certification and qualification activities specific to military aircraft. The management of airworthiness in European military aviation has undergone significant changes over the past 15 years, with the progress made attributed to the harmonisation efforts driven by the European Defence Agency (EDA). The creation of a Military Airworthiness Authorities Forum and the development of the European Military Airworthiness Requirements (EMAR) have been instrumental in creating a more homogenous regulatory landscape. The examples of five main players of the European aerospace sector, namely France, Italy, Germany, Spain and the United Kingdom, are examined from the point of view of adoption and implementation of an EMARs-based system. Their regulatory structures have revealed similarities and primary differences. The EMAR’s framework has enabled a gradual build-up of technical knowhow within the European countries who embraced this, civil-based, framework. All five countries have adopted EMARs, though through a variety of regulatory constructs. Their regulatory structures exhibit diverse practices, especially in how initial and continuing airworthiness is managed. Some countries have also elected to have more than one authority overseeing/been responsible for airworthiness. Closer collaboration between national Military Aviation Authorities (MAAs) can be achieved through standardisation at regulatory structure level. The establishment of a joint MAAs may be the next logical step in the harmonisation process, in line with EDA objective’ for a EU-wide authority with greater powers.

The relevant growth of human-machine interaction (HMI) systems in recent years is leading to the necessity of being constantly aware of the cognitive workload level of an operator, especially in a safety-critical context such as aviation. Since the confusion in the definition of this concept, this paper clarifies this terminology and also highlights its relationship with stress. Thus, we analysed the state-of-the-art of cognitive workload evaluations, showing three up-to-date methodologies: subjective, behavioural and physiological. In particular, the physiological approach is increasingly gaining attention in the literature due to today’s exponential growth of biomedical sensors. Therefore, a review of the most adopted physiological signals in the workload evaluation is provided, focusing on the aeronautical field. We conclude by highlighting the necessity of a multimodal approach for mental workload assessment as a result of this analysis.

Traditional active flutter suppression controllers are designed based on model. However, as the aircraft becomes more and more powerful, the modeling of aeroelastic system becomes difficult and the model-free requirement of controller design becomes more and more urgent. The complexity of industrial processes has brought about massive operational data generated online. Aviation industry development has entered the era of big data. Breaking through the traditional theoretical framework, mining the correlation, evolution and dynamic characteristics of the system from the data is the inevitable choice to meet this demand. In this paper, a data-driven model-free controller is designed, which relies on ridge regression of the input and output variation at each operating point of the closed-loop controlled system to recursively derive the iterative format of the control signals and ensure the numerical stability of the signals. The controller can only use the real-time measurement of the system’s online input and output data for continuous correction, to achieve the purpose of flutter suppression. Then flutter suppression of a three-degree-of-freedom binary wing with a control surface is studied, and the superiority of model-free controller is demonstrated by comparing it with the optimal controller.

On-demand urban air transportation gains popularity in recent years with the introduction of the electric VTOL (eVTOL) aircraft concept. There is an emerging interest in short/medium range eVTOL air taxi considering the critical advantages of electric propulsion (i.e. low noise and carbon emission). Using several electric propulsion systems (distributed electric propulsion (DEP)) has further advantages such as improved redundancy. However, flight controller design becomes more challenging due to highly over-actuated and coupled dynamics. This study defines and resolves flight control problems of a novel DEP eVTOL air taxi. The aircraft has a fixed-wing surface to have aerodynamically efficient cruise flight, and uses only tilting electric propulsion units to achieve full envelope flight control via pure thrust vector control. The aircraft does not have conventional control surfaces such as aileron, rudder or elevator. Using pure thrust vector control has some design benefits, but the control problem becomes more challenging due to the over-actuated and highly coupled dynamics (especially in transition flight). A preliminary flight dynamics model is obtained considering the dominant effects at hover and high-speed forward flight. Hover and forward flight models are blended to simulate the transition dynamics. Two central challenges regarding the flight control are significant nonlinearities in aircraft dynamics during the transition and proper allocation of the thrust vector control specifically in limited control authority (actuator saturation). The former challenge is resolved via designing a sensor-based incremental nonlinear dynamic inversion (INDI) controller to have a single/unified controller covering the wide flight envelope. For the latter one, an optimisation-based control allocation (CA) approach is integrated into the INDI controller. CA requires special attention due to the pure thrust vector control’s highly coupled dynamics. The controller shows satisfactory performance and disturbance rejection characteristics. Moreover, the CA plays a vital role in guaranteeing stable flight in case of severe actuator saturation.

It is a simple method to identify the hub dynamic loads of rotor by measuring the vibration responses on helicopter fuselage. However, the identification accuracy of the hub dynamic loads is related to the layout or placement of measuring points on the fuselage. The identification will be inaccurate if the layout of measuring points on the fuselage is unreasonable to result in the “ill-conditioned” frequency response function (FRF) matrix measured on the fuselage. In order to avoid the inaccurate identification due to the “ill-conditioned” measured FRF matrix, an accurate method for identifying the hub dynamic loads of rotor by vibration measurement on helicopter fuselage is proposed in this paper. In the proposed method, the reasonable layout of the measuring points on the fuselage for the “well-conditioned” measured FRF matrix can be obtained according to the condition number of the measured FRF matrix on the fuselage, and then the hub dynamic loads of rotor can be accurately identified. The simulation and experiment of the identification of the hub dynamic loads on a dynamically similar frame structure of a helicopter cockpit floor have verified the effectiveness and accuracy of the proposed method.

The deformable wing structure can change its aerodynamic shape according to the change of flight mission and flight environment, so as to obtain better lift-drag, stability and control characteristics, which is considered as one of the future research directions of aviation technology. Considering the current technology maturity and reliability, a gradient corrugated fin is designed to realise the bending deformation of the wing. The structure of the skin is optimised to keep the skin smooth during deformation. In addition, a progressive push and pull rod is proposed to drive the wing deformation, and the fluid-structure interaction simulation is carried out for the wing deformation. At the same time, the changes of wing aerodynamic characteristics under different angles of leading and trailing edges and different push rod action schemes are analysed. Finally, a dry wind tunnel simulation test of the designed progressive flexible variable bending wing is carried out. The results of fluid-structure interaction simulation and dry wind tunnel test show that the progressive flexible variable bending wing proposed in this paper has a simple and reliable structure and remarkable deformation effect. It has advantages in increasing lift and reducing drag, ensuring high lift-drag ratio and providing wing trim moment. The deformable wing dry wind tunnel test platform designed by this method is structurally reliable, easy to operate, and can accurately reflect the influence of wing deformation on its aerodynamic force, which provides a verification means for the development of the design method and the design of practical aircraft in the future.

Inflatable wings for UAVs are useful where storage space is a severe constraint. Literature in the field of inflatable wings often assumes an inflated aerofoil shape for various analyses. However, the flexible inflatable aerofoil fabric might deform to another equilibrium shape upon inflation. Hence accurate shape prediction of the inflated aerofoil is vital. Further, no standardised nomenclature or a process to convert a smooth aerofoil into its corresponding inflatable aerofoil counterpart is available. This paper analytically predicts the equilibrium shape of any inflatable aerofoil and validates the analytical prediction using non-linear finite element methods. Further, a scheme for the generation of two types of inflatable aerofoils is presented. Parameters such as the number and position of compartments and aerofoil length ratio (ALR) are identified as necessary to define the aerofoil’s shape fully. A process to minimise the deviation of the inflatable aerofoil from its original smooth aerofoil using particle swarm optimisation (PSO) is discussed. Research presented in this paper can help in performing various analyses on the actual equilibrium shape of the aerofoil.