Various types of micro-vortex generators (μVGs) are investigated for control of a supersonic turbulent boundary layer subject to an oblique shock impingement, which causes flow separation. The micro-vortex generators are embedded in the boundary layer to avoid excessive wave drag while still creating strong streamwise vortices to energise the boundary layer. Several different types of µVGs were considered including micro-ramps and micro-vanes. These were investigated computationally in a supersonic boundary layer at Mach 3 using monotone integrated large eddy simulations (MILES). The results showed that vortices generated from μVGs can partially eliminate shock induced flow separation and can continue to entrain high momentum flux for boundary-layer recovery downstream. The micro-ramps resulted in thinner downstream displacement thickness in comparison to the micro-vanes. However, the strength of the streamwise vorticity for the micro-ramps decayed faster due to dissipation especially after the shock interaction. In addition, the close spanwise distance between each vortex for the ramp geometry causes the vortex cores to move upwards from the wall due to induced upwash effects. Micro-vanes, on the other hand, yielded an increased spanwise spacing of the streamwise vortices at the point of formation. This resulted in streamwise vortices staying closer to the floor with less circulation decay, and the reduction in overall flow separation is attributed to these effects. Two hybrid concepts, named ‘thick-vane’ and ‘split-ramp’, were also studied where the former is a vane with side supports and the latter has a uniform spacing along the centreline of the baseline ramp. These geometries behaved similar to the micro-vanes in terms of the streamwise vorticity and the ability to reduce flow separation, but are more physically robust than the thin vanes.

Fluidic flight controls enable forces and moments for flight vehicle trim and manoeuvre to be produced without use of conventional moving surface controls. This paper introduces a methodology for the design of Circulation Control (CC) and Fluidic Thrust Vectoring (FTV) as fluidic controls for roll and pitch. Work was undertaken as part of the multidisciplinary FLAVIIR project, with the goal of providing full authority fluidic flight controls sufficient for a fully flapless flight of an 80kg class demonstrator aircraft known as DEMON. The design methodology considers drag, mass, volume and pneumatic power requirements as part of the overall design cost function. It is shown that the fundamental flow physics of both CC and FTV are similar, and hence there are strong similarities to the design approach of each. Flight ready CC and FTV hardware has been designed, manufactured and ground tested. The CC system was successfully wind tunnel demonstrated on an 85% scale half model of the DEMON. The design condition of a control ΔCL of 0·1 was achieved with a blowing coefficient of 0·01, giving a useable control gain of 10. The FTV system was static tested using a micro gas turbine source. The control characteristic was ‘N’ shaped, consisting of an initial high gain response in a negative sense (gain = −30) followed by a low gain response in a positive sense (gain = +3) at higher blowing rate. CC and FTV control hardware directly contributes to around 6% to the overall mass of the flight vehicle, however provision of pneumatic power carries a significant mass penalty unless generated as part of an integrated engine bleed system.

The introduction of new larger aeroplanes presents the ICAO Instrument Flight Procedures Panel (IFPP) with the need to review the requirements for the Obstacle Free Zone. To support future decisions, the IFPP took the initiative to ask for the development of pilot models which are capable to control the simulated aircraft during the approach — go-around manoeuvre. The aim of this development was to obtain a tool to perform Monte Carlo simulations for the determination of the flight path statistics of the manoeuvre. In 2001, both QinetiQ and the National Aerospace Laboratory (NLR) were invited to develop pilot models. The two pilot models are based on fundamentally different descriptions of a pilot’s control behaviour. The QinetiQ pilot model is based on a discrete-event representation of pilot control movements and has been developed in the Integrated Performance Modelling Environment (IPME). The NLR pilot model is based on control engineering and is a linear model with visual and motion feedback extended with stochastic disturbances. This development was supported by Boeing, which provided a simulation model of the B747–400 as the representative aircraft model. The integration of the pilot models with the aircraft model was performed by Boeing. Statistical data on the flight path tracking during the approach – go-around manoeuvre and on discrete pilot actions were obtained from simulations performed in a full flight simulator (FFS) at NASA Ames and a fixed-base simulator at Boeing. Both pilot models, the use of the statistical data from the simulations and the integration with the aircraft model are discussed in the paper.

This paper addresses the development of multiple UAV deployment simulation models that include representative aerodynamic cross-coupling effects. Applications may include simulations of autonomous aerial refuelling and formation flying scenarios. A novel wake vortex model has been developed and successfully integrated within a Matlab/Simulink simulation environment. The wake vortex model is both sufficiently representative to support studies of aerodynamic interaction between multiple air vehicles, and straightforward enough to be used within real time or near real time air-to-air simulations. The model integration process is described, and computational results of a two-vehicle-formation flight are presented.

Current sonic boom theory is based on linear midfield solutions coupled with acoustic propagation models. Approximate corrections are made within the theory to account for non-linearities, in particular for the coalescence of compression waves and the formation of weak shocks. A very large adjustment is made to account for the increasing acoustic impedance that the waves encounter as they propagate from the low density air at cruise altitude to the high density air at sea level. Typically this correction reduces the calculated over pressure levels by a factor of three. Here the method of characteristics (MOC) is used to prove that the density gradient within a hydrostatic atmosphere has no direct effect on the propagation or intensity of the wave. However gravity and ambient temperature both affect the wave propagation and the combined pressure level attenuation is not dissimilar to that previously attributed to acoustic impedance. Although the flawed acoustic theory has given reasonable predictions of measured sonic booms, the omission of gravity from the equation of motion and the inclusion of a false impedance modification, makes the model unreliable for prediction of future designs, particularly those focused on boom minimisation. As an aid to quiet supersonic aircraft design, Whitham’s theory is extended to include gravity and ambient temperature variation and shown to be in good agreement with a MOC solution for the real atmosphere.