This paper aims at developing an aeroelastic model for the instability analysis of supersonic thick fins. To this aim the modal analysis technique is used for the structural dynamics modelling of a fin with a general structure. An unsteady aerodynamic model is applied based on the shock/expansion analysis over the flat surfaces of the fin along with local application of the piston theory. Assuming a supersonic fin with an arbitrary polygonal cross-section, thickness and initial angle-of-attack, the steady flow properties (e.g. Mach number, density and temperature) are calculated over the flat surfaces of the fin. Then, assuming small amplitude vibrations, the generalised aerodynamic forces are obtained in terms of the structural modal coordinates. Using the obtained model, the effect of thickness, initial angle-of-attack, taper ratio and sweep angle on the aerodynamic derivatives and aeroelastic stability of the fin are studied which show their remarkable effects on the instability Mach number and its type. Specially, the presented results show that increasing the fin thickness dramatically diminishes the stability margin mainly at low angles of attack. Also a sharp decrease of the divergence Mach number is observed by increasing the fin’s incidence angle.

One of the most resent efforts in aircraft design is the replacement of aluminium structures by carbon fibre reinforced polymer composites. Due to lower material and manufacturing costs, doubly curved shapes covering big areas are preferred over simpler surfaces which integrate stiffening profiles. In this context, CAD parameterisation of surfaces allows design solutions by means of classical shape optimisation. Related geometrical parameters are manipulated towards optimal design, generating innovative geometries and detailing.

The presented structure is optimised by reducing the overall weight. The final optimum is guided using stability and strength restrictions in order to assure the safety of the component. Geometrical considerations are also included due to operational reasons. A hierarchical design procedure is developed which results in a work flow from preliminary ‘parameter-free’ form finding motivated by solving the minimal surface problem. The geometrical model for optimisation is recovered by generating B-Spline surface patches to preserve continuity requirements over large regions. The number of geometrical coefficients are defined by the accuracy in surface generation and the required freedom in surface control. The hierarchical approach reduces the possibilities of ending with an unsatisfactory optimum when several local minima characterise the non-linear problem, as it is usually the case in shape optimal design. A geometrical non-linear analysis is used to verify the performance of the optimum.

On the basis of well-known literature, an analytical tool named LEAF (linear elastic analysis of fracture) was developed by the authors to predict the damage tolerance (DT) proprieties of aeronautical stiffened panels. The tool is based on the linear elastic fracture mechanics and the displacement compatibility method. By means of LEAF, an extensive parametric analysis of stiffened panels, representative of typical aeronautical constructions, was performed to provide meaningful design guidelines. The effects of riveted, integral and adhesively bonded stringers on the fatigue crack propagation performances of stiffened panels were investigated, as well as the crack retarder contribution using metallic straps (named doublers) bonded in the middle of the stringers bays. The effect of both perfectly bonded and partially debonded doublers was investigated as well. Adhesively bonded stiffeners showed the best DT properties in comparison with riveted and integral ones. A great reduction of the skin crack growth propagation rate can be achieved with the adoption of additional doublers bonded between the stringers.

Results from numerical simulations of the three dimensional flow in the intake-isolator of a dual mode scramjet are presented. The FANS calculations have utilised the SST k -ω turbulence model. The effect of cowl length and cowl convergence angle on the inlet mass capture ratio, flow distortion, shock strength and pressure rise are studied in detail. Three cowl lengths and four or five cowl convergence angles for each cowl length are considered. The predicted values of the dimensionless wall static pressure and inlet mass capture ratio are compared with experimental data reported in the literature. The numerical predictions are shown to agree well with the experimental data. In addition, details of the flow field such as shocks, expansion fans and shock boundary interaction are also captured accurately. Inlet unstart is also demonstrated for one case.

This contribution addresses the subject of engine inlet barrier filters (IBF) for rotorcraft. The purpose of an IBF is to mitigate the risk of particle ingestion by the engine, a situation that can cause irrevocable damage to key components. The risk is significantly elevated during a brownout landing, in which the rotor wake of a descending helicopter interacts with loose ground sediment, causing the generation of a dust cloud. In such a condition, an IBF successfully removes particles from the engine-bound air at the expense of a pressure drop, which grows temporally. The increase in pressure drop is caused by but not limited to an increase in incident velocity and a decrease of mean particle size; however the rate may be slowed by operating the filter at a tangential angle to the flow. The current work presents findings of a parametric study into the factors affecting particle accumulation and the consequential loss of inlet total pressure.