Hostname: page-component-cd9895bd7-hc48f Total loading time: 0 Render date: 2024-12-25T06:34:58.197Z Has data issue: false hasContentIssue false
  • English
  • Français

Performance of straight-walled annular diffusers with swirling flow

Published online by Cambridge University Press:  04 July 2016

E. D. Klomp
E. D. Klomp*
Affiliation:
Engine Research DepartmentGeneral MotorsWarren, USA
Get access Rights & Permissions [Opens in a new window]

Abstract

Performance data are presented for eight annular diffuser families, a family being defined by the inner and outer cone angles and the inlet hub-tip ratio. These results include profiles of velocity and total pressure across the inlet and outlet lanes as well as overall pressure recovery coefficients. Diffuser outer cone angles range from 10° to 60° and inner cone angles from 59° to -19°. Swirl angles were varied from 0° up to 44°. Each diffuser family was tested over a range of lengths and swirl angles resulting in over ninety different tests. A procedure for extending the non-swirling definition of effectiveness to swirling flows is presented and used to evaluate a limiting swirl angle for separation for free-vortex-type inlet swirl. Comparisons are made to several measured values of flow separation. Some experimental diffusers exhibited a violently unsteady hub stall which apparently consisted of rotating reverse flow regions.

Type
Research Article
Information
The Aeronautical Journal , Volume 101 , Issue 1010 , December 1997 , pp. 467 - 480
Copyright
Copyright © Royal Aeronautical Society 1997 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Kaiser, K.F. and Mcdonald, A.T. Effect of wake-type nonuniform inlet velocity profiles on first appreciable stall in plane-wall diffusers. Trans ASME, J Fluids Eng, 1980, 102, (283).Google Scholar
2. Kline, S.J., Abbott, D.E. and Fox, R.W. Optimum design of straight- walled diffusers, Trans ASME, Series D, J Basic Eng, 1959, 81, (321).Google Scholar
3. Kline, S.J. and Rundstadler, P.W. Some preliminary results of visual studies of the flow model of the wall layers of the turbulent boundary layers, Trans ASME, J App Mech, 1959,166 Google Scholar
4. Kline, S.J. Observed structure features in turbulent and transition boundary layers, Fluid Mech Int Flows, 1967, 27.Google Scholar
5. Reneau, L.R., Johnston, J.P. and Kline, S.J. Performance and design of straight two-dimensional diffusers, Report PD-8, Thermosciences Division, Mechanical Engineering Department, Stanford University, September 1964.Google Scholar
6. Cockrell, D.J. and Markland, E. A review of incompressible diffuser flow, AitcrEng, 1963, 35, (286).Google Scholar
7. Sprenger, H. Experimenteduntersuchungenangeradenund gekrummten diffusoren. Mitteilung aus dem Institute fur Aerodynamik anderETH, 27, 1959.Google Scholar
8. Sovran, G. and Klomp, E.D. Optimum geometries for rectilinear diffusers with rectangular, conical, and annular cross-section, Fluid MechInt Flows, 1967,270.Google Scholar
9. Stevens, S.J. The performance of annular diffusers, Proc IMechE, 1967, 192, (58) Part 3.Google Scholar
10. Elkersh, A.M., Eloammal, A.H. and Maccallum, N.R. An experimentalinvestigationof theperformanceof equiangularannular diffusers with swirling flow, Proc IMechE, 1995,199, (293).Google Scholar
11. Lohmann, R.P., Markowski, S.J. and Brookman, E.T. Swirling Flow Through Annular Diffusers with Conical Walls, Trans ASME, J Fluids Eng, 1979, 101, (224).Google Scholar
12. Kamemoto, T., Toyokura, T. and Kurokawa, J. Flow in annular diffusers, BullJSME, 1982, 25, (204).Google Scholar
13. Lai, Y.G., So, R.M.C. and Hwang, B.C. Calculation of planar and conical diffuser flows, AlAA J, 1989, 27, (542).Google Scholar
14. Singh, R.K. and Azad, R.S. The Structure of Instantaneous Reversals in Highly Turbulent Flows, Exp In Fluids, 1995, 18, (409).Google Scholar
15. Japikse, D. and Pampreen, R. Annular diffuser performance for an automotive gas turbine, Trans ASME, J Eng For Power, 1979, 101, (358).Google Scholar
16. Greitzer, E.M. Review-axial compressor stall phenomena, Trans ASME, J Fluids Eng, 1982, 102, (134).Google Scholar
17. Escudier, M.P. and Zehnder, N. Vortex Flow Regimes, J Fluid Mech, 1998,(105).Google Scholar