Hostname: page-component-cd9895bd7-mkpzs Total loading time: 0 Render date: 2024-12-25T06:17:58.758Z Has data issue: false hasContentIssue false

Flow past two tandem circular cylinders of unequal diameter

Published online by Cambridge University Press:  04 July 2016

S. C. Luo
Affiliation:
Department of Mechanical and Production Engineering National University of Singapore
T. L. Gan
Affiliation:
Department of Mechanical and Production Engineering National University of Singapore

Summary

The present work investigates the structure associated with flow past two tandem circular cylinders with a diameter ratio of 0·33. The smaller cylinder is always upstream. The two parameters varied in the present work are the spacing between the cylinders denoted by l/d2where l is the centre to centre spacing and d2 is the diameter of the downstream cylinder, and the Reynolds number Re based on d2 Just like the case of flow past two equal size cylinders, a critical spacing was found to exist. For spacing less than the critical value, shear layers that separate from the upstream cylinder reattach onto the downstream cylinder (reattached flow regime) whereas for spacing larger than the critical value both cylinders shed vortices (co-shedding flow regime). For diameter ratio dl/d2 of 0·33 and at Re ≈ 6·27 × 104, the critical spacing is at l/d2 ≈ 1·8 to 2·2. In 1·8 ≤ l/d2 ≤ 2·2, bi-stable flow situation where the flow structure changes intermittently between the reattached and the co-shedding types was observed and the probability that the flow is co-shedding within the bi-stable regime is found to follow a normal distribution.It was also found that the reattached flow regime can be sub-divided into two sub-regimes. In 0·66 ≤ l/d2 ≤ 1·2 (sub-regime 1), the vortex formation length, lf, of vortices shed by the downstream cylinder appears to be shorter, resulting in larger drag force on the downstream cylinder and larger r.m.s. pressure around it. In 1·4 ≤ l/d2 ≤ 1·18 (subregime 2), lf appears to be larger which results in a smaller drag force and smaller r.m.s. pressure distribution when compared with sub-regime 1. Only the downstream cylinder has a Strouhal number S2 associated with it in the reattached flow regime. The general trend is that of a slight reduction in S2 with increasing l/d2 which is consistent with the relation of larger lf at larger l/d2 in the reattached flow regime. In the coshedding regime, the Strouhal numbers of both cylinders are similar.

The Reynolds number was varied in the range 3·15 × 104 ≤ Re ≤ 8·81 × 104. It was observed that both the mean drag and the r.m.s. lift and drag forces reduce in magnitude when Re was increased. From the spectra of the lift force, reduction in C'L was found to be due to a reduction in the regularity of the vortex shedding process. From the pressure distribution of the downstream cylinder at constant l/d2, it was found that the reduction in mean drag with increasing Re is caused by an increase in base pressure which in turn is likely to be the consequence of an increase in vortex formation length. The upper and lower limits of the range in the lldi at which bistable flow was detected were found to decrease with increasing Re. At l/d2 = 2·0, the flow was of the reattached type at Re = 3·15 × 104 and 4·75 × 104 but became bi-stable at Re ≥ 6·27 × 104.

Type
Research Article
Copyright
Copyright © Royal Aeronautical Society 1992 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Novak, J. Strouhal number of two cylinders of different diameter arranged in tandem. Acta CSAV, 1975, p 366.Google Scholar
2. Hiwada, M., Taguchi, T., Mabuchi, T. and Kumada, M. Fluid flow and heat transfer around two circular cylinders of different diameter in cross flow. Bull JSME, 1979, 22, p 715.Google Scholar
3. Baxendale, A. J. Grant, I. and Barnes, F. H. The flow past two cylinders having different diameters. Aeronaut J, 1985, 89, p 125.Google Scholar
4. Baxendale, A. J. Grant, T. and Barnes, F. H. Vortex shedding from two cylinders of different diameters. J Wind Eng Ind Aerodynam, 1986, 23, p 427.Google Scholar
5. Lesage, F. and Gartshore, I. S. A method of reducing drag and fluctuating side force on bluff bodies. J Wind Eng Ind Aerodynam, 1987, 25, p 229.Google Scholar
6. Gowda, B. H. L. and Prabhu, D. R. Interference effects on the flow-induced vibrations of a circular cylinder. J Sound Vibration, 1987, 112, p 487.Google Scholar
7. Arie, M., Kiya, M., Moriya, M and Mori, H. Pressure fluctuations on the surface of two circular cylinders in tandem arrangement. Trans ASME J Fluids Eng, 1983, 105, p 161.Google Scholar
8. Bearman, P. W. and Luo, S. C. Investigation of the aerodynamic instability of a square-section cyclinder by forced oscillation. J Fluids Struct, 1988, 2, p 161.Google Scholar
9. Irwin, H. P. A. H., Cooper, K. R. and Girard, R. Correction of distortion effects caused by tubing systems in measurements of fluctuating pressures. J Ind Aerodynam, 1979, 5, p 93.Google Scholar
10. Luo, S. C. and Chew, Y. T. A smoke wires flow visualization study of the wakes of bluff bodies with different afterbodies. Proceedings of the Fifth International Symposium on Flow Visualization, Prague 1989.Google Scholar
11. Igarashi, T. Characteristics of the flow around two circular cylinders arranged in tandem (1st Report). Bull JSME, 1981, 24, p 323.Google Scholar
12. Ang, A. H. S. and Tang, W. H. Probability concepts in engineering planning and design, Vol. 1—Basic Principles (chapter 6), 1975, John Wiley and Sons.Google Scholar
13. Bearman, P. W. On vortex shedding from a circular cylinder in the critical Reynolds number regime. J Fluid Mech, 1969, 37, p 577.Google Scholar