Hostname: page-component-cc8bf7c57-n7pht Total loading time: 0 Render date: 2024-12-12T04:59:48.827Z Has data issue: false hasContentIssue false
  • English
  • Français

Flow over a glider canopy

Published online by Cambridge University Press:  27 January 2016

A. S. Jonker ,
J. J. Bosman ,
E. H. Mathews  and
L. Liebenberg
A. S. Jonker
Affiliation:
School of Mechanical and Nuclear Engineering, North-West University (Potchefstroom campus), Potchefstroom, South Africa
J. J. Bosman
Affiliation:
School of Mechanical and Nuclear Engineering, North-West University (Potchefstroom campus), Potchefstroom, South Africa
E. H. Mathews
Affiliation:
Centre for Research and Continued Engineering Development, North-West University (Pretoria campus), Lynnwood Ridge, South Africa
L. Liebenberg*
Affiliation:
Centre for Research and Continued Engineering Development, North-West University (Pretoria campus), Lynnwood Ridge, South Africa
*
[email protected]
Get access Rights & Permissions [Opens in a new window]

Abstract

In order to minimise drag, the front part of most modern glider fuselages is shaped so that laminar flow is preserved to a position close to the wing-to-fuselage junction. Experimental investigations on a full-scale JS1 competition glider however revealed that the laminar boundary layer in fact trips to turbulent flow at the fuselage-to-canopy junction position, increasing drag. This is possibly due to ventilation air leaking from the cockpit to the fuselage surface through the canopy seal, or that the gap is merely too large and therefore trips the boundary layer to turbulent flow. The effect of air leaking from the fuselage-to-canopy gap as well as the size of the gap was thus investigated with the use of computational fluid dynamics. It was found that if air was leaking through this gap the boundary layer would be tripped from laminar to turbulent flow. It was also found that the width of the canopy-to-fuselage gap plays a significant role in the preservation of laminar flow. If the gap is less than 1mm wide, the attached boundary layer is able to negotiate the gap without being tripped to turbulent flow, while if the gap is 3mm and wider, it will be tripped from laminar to turbulent flow. The work shows that aerodynamic drag on a glider can be significantly minimised by completely sealing the fuselage-to-canopy gap and by ensuring a seal gap-width of less than 1mm.

Type
Research Article
Information
The Aeronautical Journal , Volume 118 , Issue 1204 , June 2014 , pp. 669 - 682
Copyright
Copyright © Royal Aeronautical Society 2014 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Althaus, D. Wind-tunnel measurements on bodies and wing-body combinations, Motorless Flight Research, NASA CR-2315, November 1972.Google Scholar
2. Ostrowski, J., Litwinczyk, M. and Turkowski, L. Characteristics of flow past fuselages and wing-fuselage systems of glider, NASA TM-75401, Washington, DC, USA, National Aeronautics and Space Administration, 1978.Google Scholar
3. Schreur, W.B. The ventilation of streamlined human powered vehicles, Human Power eJournal, [online] Available at: <http://www.hupi.org/HPeJ/Index.htm> (Accessed on 18 February 2011), 2004.+(Accessed+on+18+February+2011),+2004.>Google Scholar
4. Tamai, G. The Leading Edge: Aerodynamic design of ultra-streamlined land vehicles, Cambridge, Robert Bentley Publishers, 1999.Google Scholar
5. Schumann, W.E. Glider performance improvements, [online] Available at <http://www.betsybyars.com/guy/soaring_symposia/> [Accessed on 8 October 2012] The 1972 American Soaring Symposium, Mont Chateau Lodge, Morgantown, West Virginia, USA, 12-13 February 1972.+[Accessed+on+8+October+2012]+The+1972+American+Soaring+Symposium,+Mont+Chateau+Lodge,+Morgantown,+West+Virginia,+USA,+12-13+February+1972.>Google Scholar
6. Sinclair, J.J. Internet forum on glider cockpit ventilation, [online] Available at: <http://www.aviationkb.com/Uwe/Forum.aspx/soaring/602/ASW-24-27-rear-fuselarge-vents.> [Accessed on 10 December 2010], 2003.+[Accessed+on+10+December+2010],+2003.>Google Scholar
7. Bickle, P.F. Sailplane Preparation for Competition, Available at: <http://www.betsybyars.com/guy/soaring_symposia/> [Accessed on 8 October 2012], The 1971 American Soaring Symposium, Mont Chateau Lodge, Morgantown, West Virginia, USA, 13-14 February 1971.+[Accessed+on+8+October+2012],+The+1971+American+Soaring+Symposium,+Mont+Chateau+Lodge,+Morgantown,+West+Virginia,+USA,+13-14+February+1971.>Google Scholar
8. Boermans, L.M.M. and Terleth, D.C. Wind–tunnel tests of eight sailplane wing-fuselage combinations, Tech Soaring, 1983, 8, (3), pp 70–85.Google Scholar
9. Holmes, B.J., Obara, C.J., Martin, G.L., Glenn, L. and Domack, C.S. Manufacturing tolerances for natural laminar flow airframe surfaces. SAE Paper 850863.Google Scholar
10. Schlichting, H. Boundary Layer theory, New York, USA, McGraw-Hill Book Company, 1979.Google Scholar
11. Galvao, F.L. A note on low drag bodies, OSTIV Publication X, Hobbs: Soaring Society of America, 1968.Google Scholar
12. Kubrynski, K. Application of the panel method to subsonic aerodynamic design; Application of the panel method to subsonic aerodynamic design, Inv Probl Engng, 1997, 5, (2), pp 87–112.Google Scholar
13. Goldschmied, F. Fuselage self-propulsion by static- pressure thrust – Wind-tunnel verification, AIAA/AHS/ASEE Aircraft Design, Systems and Operations Meeting, 14-16 September 1987, St Louis, Missouri, USA.Google Scholar
14. Walters, D.K. and Leylek, J.H. Computational fluid dynamics study of wake-induced transition on a compressor-like flat plate, J Turbomach, 2005, 127, (1), pp 52–63.Google Scholar