Hostname: page-component-78c5997874-8bhkd Total loading time: 0 Render date: 2024-11-09T22:42:03.119Z Has data issue: false hasContentIssue false
  • English
  • Français

Stress Determination in an Adhesive Bonded Joint by X-Ray Diffraction*

Published online by Cambridge University Press:  06 March 2019

Paul Predecki  and
Charles S. Barrett
Paul Predecki
Affiliation:
University of Denver Research Institute, Denver, Colorado 80208
Charles S. Barrett
Affiliation:
University of Denver Research Institute, Denver, Colorado 80208
Get access

Extract

At the present time there is considerable interest in the use of adhesive bonded joints for structural applications. The design of such joints is based mostly on finite element calculations and failure tests rather than on strain or stress measurements. To our knowledge no measurements have been made of stresses at or near the adhesive/adherend interface (where many bond failures occur) because of difficulties with accessibility. The purpose of this work was therefore to try to make such measurements using X-ray diffraction.

The approach taken was to gain access to the bond by making one of the adherends in a single lap joint to be relatively transparent to X-rays and the cither relatively opaque. Incident X-rays then penetrated the first adherend and the adhesive and were diffracted from gains in the second adherend adjacent to the adhesive/adherend interface. Stresses resulting from curing of the adhesive were determined first, after which a load was applied and the stresses redetermined.

Type
II. X-Ray Strain and Stress Determination
Information
Advances in X-Ray Analysis , Volume 27: Thirty-Second Annual Conference on Applications of X-ray Analysis, August 1-5, 1983 , 1983 , pp. 251 - 260
Copyright
Copyright © International Centre for Diffraction Data 1983

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Footnotes

*

Work supported by ARO on Grant No. DAAG29-81-0150.

References

1. See for example Graff, G., The Glued-Together Airplane, High Technology 3:67 (1983), September issue.Google Scholar
2. Charles S. Barrett and Paul Predecki, Stress Measurement in Graphite/Epoxy Uniaxial Composites by X-Rays, Polymer Composites 1:2 (1980).Google Scholar
3. Paul Predecki and Charles S. Barrett, Progress Reports #2 and 3 on ARO Grant No. DAAG29-81-0150. Jan. 1982-Jan. 1983. Manuscript in preparation.Google Scholar
4. Residual Stress Measurement by X-Ray Diffraction, SAE Information Report #SAE J784a. Aug. 1971.Google Scholar
5. See for example, Cohen, J. B., Dolle, H. and James, M. R., Stress Analysis from Powder Diffraction Patterns, in “NBS Special Pub. 567:Accuracy in Powder Diffraction,“ S. Block and Hubbard, C. R., eds. pp. 453–477 (Feb, 1980).Google Scholar
6. McClintock, F. A. and Aragon, A. S., “Mechanical Behavior of Materials,” Addison-Wesley, p. 61 (1966).Google Scholar
7. Adams, R. D. and Peppiatt, N. A., Stress Analysis of Adhesive-Bonded Lap Joints, Jnl. of Strain Analysis 9:185 (1974).Google Scholar
8. Viscoelastic Stress Analysis Including Moisture Diffusion for Adhesively Bonded Joints, Romanko, J., P.I., MRL Report FZM-6838, General Dynamics, Fort Worth, (1980).Google Scholar
9. Stronge, W. J. and Heindahl, O. E. R., Stress in Single Lap Joints of Dissimilar Materials, Naval Weapons Center, China Lake, Report NWC TP 6242 (1981).Google Scholar
10. Francis, E. C., Huffered, W. L., Lewin, D. G., Thompson, R. E., Briggs, W. E., Time Dependent Fracture in Adhesive Bonded Joints, Interim Report #AFWAL-TR, CSD 2769-IR-01, (May 1982).Google Scholar