Resonant Bessel-beam launchers (BBLs)are radiating devices constituted by a cylindrical metallic cavity with a partially reflecting sheet (PRS) on top. Millimeter-wave resonant BBLs typically exhibit transverse magnetic (TM) polarization due to the use of coaxial probes as feeders and homogenized metasurfaces as PRS. Launchers showing either a purely transverse electric (TE) or a hybrid (quasi-TE) polarization have recently been proposed for realizing wireless power transfer (WPT) links in the radiative near-field region at millimeter waves. The former are obtained by means of a radial slot array as a feeder and a homogenized metasurface as a PRS. The latter are obtained by using a loop antenna as a feeder and an annular strip grating in the homogenization limit as radiating aperture. In this work, based on an original semi-analytical model, such a metasurface is demonstrated to show a dichroic behavior. This interpretation explains the improvement in terms of polarization purity with respect to more nondichroic conventional homogenized metasurfaces. The behavior of the annular strip grating under a pure TM polarization is tested with a coaxial feeder, whereas its behavior under a pure TE polarization is tested by means of the radial slot array feeder. Results confirm the validity of the proposed analysis, which is finally exploited to evaluate the WPT performance.

This paper proposes a triple-band fractal slot antenna with enhanced gain operating at frequencies of 2.7, 3.5, and 4.8 GHz for microwave wireless power transmission. The antenna achieved more than 3 dB gain by preserving the symmetrical defected reflector structure behind it at a length of 0.54λ/4, where λ is the wavelength in free space at 2.7 GHz. A 50 Ω micro-strip line coupled at 66 mm length helps feed the triple band slot antenna. The purpose of a triple-band rectifier circuit with an impedance network is to convert the radio frequency (RF) signal into direct current. The measurements reveal that the antenna’s enhanced gain is 8.8 dB, and the rectifier’s highest RF signal to direct current conversion efficiency is 74.3%. For the combined configuration unit of measure, the antenna is assimilated into the rectifier via back-to-back 50 Ω Sub Miniature Version A (SMA) connectors. The highest recorded efficiency of 49.67% was obtained for the rectenna at optimum values of 1 kΩ resistive load and −5 dBm power input. It has been revealed that the rectifier-integrated antenna presented is effective for low-input RF energy capture and power transmission.

This review paper explores the potential use of the planar miniaturized antenna for wireless capsule endoscopy application: one of the promising fields in the current era. The paper highlights the design strategy, various optimization techniques with respect to system realization, material compatibility issues and finally the mandatory EM radiation effect analysis for the said application. It compares amongst various currently reported structures in context with different performance metrics. Inherent challenges of this emerging field of bio-medical engineering have also been detailed here along with futuristic approaches for enhancing the throughput.

This paper presents a rollable metamaterial screen for high-efficiency wireless power transfer (WPT) system based on magnetic resonance coupling, which operates at 4.5 MHz. The rollable metamaterial screen with a fully expanded area of 750 mm × 750 mm is located in the middle between transmitter and receiver coils and focuses the magnetic field and, by such a way, significantly improves power transfer efficiency (PTE). The metamaterial screen can be rolled up, e.g. onto the ceiling when it is not used, and thus does not require any designated space for the screen saving space. A WPT system with the rollable metamaterial screen is designed, fabricated, and characterized. Improved PTE is qualitatively and quantitatively verified by light bulb experiments and vector network analyzer measurements. The PTE of the WPT system with the metamaterial screen increases from 36 to 58.52% and 10.24 to 31.36% for the distances between the transmitter and receiver coils 100 and 150 cm, respectively. The effects of lateral and angular misalignments on the PTE of the WPT system are also studied. Obtained results show that the rollable metamaterial screen improves the PTE even at the misaligned condition.

Distribution of wireless power charging field uniformly on a large area pad is critical for power receivers, particularly for wearable devices, wherein small form factor coils are involved. Since the receiver coil size is quite limited in these types of applications, the device is very sensitive to the amount of field it could retain and hence, it needs special placement or snapping mechanism to fix it at an optimum location for reliable wireless charging. In order to overcome this limitation for the end-user, a dual-mode multi-coil power transceiver system is proposed; utilizing resonance filtering to increase the amount of total power delivered with the rather uniform spatial distribution. Two concentric coils; center one driven by 6.78-MHz high-frequency driver (A4WP) and the outer larger one with a 200-KHz low-frequency driver (Qi) with resonant blocker could transfer up to 50 mW standards compliant flat power to a 13-mm radius 30-turns wearable receiver coil everywhere across an 8-cm radius charging pad area without any alignment requirement or snapping. Two different feedback topologies corresponding to each of the H-Bridge power drivers were also presented as an automatic series resonance coil drive frequency lock mechanism, extracting peak powers for each system individually from a standard 5 V-1A USB wall charger.

Radiofrequency ablation (RFA) is a non-invasive image-guided procedure where tumors are heated in the body with electrical current. RFA procedures are commonly indicated for patients with limited local disease or who are not surgical candidates. Current methods of RFA use multiple cords and wires that ergonomically complicate the procedure and present the risk of cutting or shorting the circuit if they are damaged. A wireless RFA technique based on electromagnetic induction is presented in this paper. The transmitting and receiving coils were coupled to resonate at the same frequency to ensure the highest power output. The receiving coil was connected to two insulated electrodes on a catheter, which allowed the current to flow to the targeted tissue. The prototype system was tested with ex-vivo bovine tissue, which has similar thermal and electrical properties to human tissue. The setup can monitor the received power, efficiency, temperature, and ablation zone during ablation procedures. The maximum received power was 15 W, and the average maximum efficiency was 63.27%. The novel system was also able to ablate up to a 2 cm ablation zone in non-perfused tissue. This proof of concept for performing RFA wirelessly with electromagnetic induction may merit further optimization.

Telemetry acquisition from rodents is important in biomedical research, where rodent behavior data is used to study disease models. Telemetry devices for such data acquisition require a long-term powering method. Wireless power transfer (WPT) via magnetic resonant coupling can provide continuous power to multiple small telemetric devices. Our loosely coupled WPT (LCWPT) system consists of a stationary primary coil and multiple freely moving secondary coils. Our previous LCWPT system was designed to transfer reasonable power to secondary coils at poor orientations but transfers excessively high amounts of power at favorable orientations. Reasonable power is needed for telemetry and radio electronics, but highly induced voltage on the secondary coil creates excess energy which must be dissipated by previous devices, and caused problems (localized heat damage and variations in component properties) leading to drift in operating frequency. To remedy these two problems, a novel scheme is proposed to automatically tune or detune the resonant frequency of the secondary circuit. Our closed-loop controlled tuning or detuning (CTD) approach can be used to prevent excessive power transfer by detuning, or to improve power transfer by tuning, depending on the need. Furthermore, this novel CTD scheme facilitates the use of multiple telemetric devices.

The characteristic transfer parameters of inductive power transfer systems highly depend on the relative position of the coils to each other. While translational offset has been investigated in the past, the effect of rotatory offset on the transfer parameters is widely unclear. This paper contains simulation results of an inductive power transfer system with a rotatory offset in three axes and shows the possible improvements in the coupling coefficient. As a result, rotation angles can be used as control parameters and thereby increase the system efficiency. Alternatively, the allowed misalignment area of the secondary coil can be increased while maintaining the functionality and same dimensions.

Advances in material science and semiconductor technology have enabled a variety of inventions to be implemented in electronic systems and devices used in the medical, telecommunications, and consumer electronics sectors. In this paper, a wireless charging system is described as a wearable body heater that uses a chair as a transmitter (Tx). This system incorporates the widely accepted Qi wireless charging standard. Alignment conditions of a linear three-element coil arrangement and a 3 × 3 coil matrix array are investigated using voltage induced in a coil as a performance indicator. The efficiency obtained is demonstrated to be up to 80% for a voltage of over 6.5 Volts and a power transfer of over 5 Watts. Our results and proposed approach can be useful for many applications. This is because the wireless charging system described herein can help design seating areas for the elderly and disabled, commercial systems, consumer electronics, medical devices, electronic textiles (e-textiles), and other electronic systems and devices.

Wireless power transmission (WPT) systems with moveable mechanical parts have been acquired more and more attention during the past decade. However, due to the moveable feature of transmitting coil and receiving coil, misalignment issue lead to extra power loss, decrease in efficiency, increase in control complexity, and unwanted performance degradation of the whole system. Moreover, it happened frequently than those traditional planar coils systems. The motivation for this paper is trying to have a deep understanding of quantitative relationship between ball-shaped coils mutual inductance and misalignment. Based upon that, engineers would know more detail of the coils position and mutual inductance. So, optimized design might be achieved. On considering that, this paper presents a WPT system with a ball-shaped coil for robot joints. A mutual inductance calculation based on filament method aimed at ball-shaped coil is proposed. Based on these, nine different ball-shaped coil solutions are calculated. Then, model with a minimized change rate of mutual inductance against the angular misalignment is chosen as the optimized design. Circuit analysis of the WPT system with the series–series resonant topology is conducted to choose a proper working frequency and load. Finally, an experimental platform is established. It demonstrates the feasibility of the proposed calculation method and the feasibility of the WPT prototype.

This work presents a novel efficient and compact size coupled resonator system for wireless power transfer (WPT) based on compact half-ring resonators defected ground structure (HRRs-DGS). The proposed design is capable of supplying low power electronic devices. The suggested system is based on coupled resonators of DGS. An HRR-DGS band-stop filter is designed and proposed, and when two HRRs-DGS are coupled back-to-back, it transfers to a band-pass filter leading to a compact and highly efficient WPT system working at 3.4 GHz. The measured efficiency of the proposed coupled HRRs-DGS system is around 94% at a transmission distance of 12 mm which is filled with foam for stable measurements. The proposed design is suitable for charging electronic devices such as wireless sensor nodes at 3.4 GHz. Simulation and experimental results have shown acceptable agreement.

By using quasi-optical tools, it is possible to approximate microwave radiation to Gaussian beams, which enables the study of its propagation and coupling to different components. Hence, their usefulness for wireless power transfer and rapid system design. In this paper, a system composed of two reflectors is analyzed both theoretically and by discussing two cases where quasi-optical tools were applied. The near- and far-field regimes were considered and corresponding frequencies of operation, beam radius, and radius of curvature were computed.

Impedance matching is very important to improve transmission efficiency not only for wireless communication but also for wireless power transfer. Lumped reactive elements are usually used in the impedance matching circuit. These reactive components such as inductors and capacitors have ohmic loss. An exact approach to design the lumped matching circuit at the presence of the ohmic loss is derived in this paper. Moreover, the condition for selection of impedance matching topology is deduced not only for lossless case but also for lossy case. Finally, the effect of the ohmic loss in the impedance matching circuit on the transmission efficiency is demonstrated quantitatively.

In this paper, a theoretical study for the design of multi-source transmitters suitable for perpendicular dynamic wireless power transfer is presented. Unlike conventional systems, the concept presented here overcomes the traditional limitation on the receiver's orientation by providing an optimal distribution of the transmitted energy obtained by using different sources. For this purpose, a theoretical study of different transmitters has been achieved by solving the inverse problem. Comparison with conventional single-source transmitters carrying the same total current as the multi-source transmitters, shows a significant enhancement of the power gain when a Genetic Algorithm is used. The obtained theoretical results show power gain levels over 7.5 dB for different path lengths at different heights. At the end, a solution for a path of an infinite length is presented.

This paper deals with the shielding of the magnetic field generated by two planar coils of a wireless power transfer (WPT) system at the frequency of tens of kilohertz used in automotive applications. Different shielding techniques using conductive and magnetic materials are examined and discussed highlighting strong and weak points of each other. Finally, the proposed shielding configuration consisting of a combined conductive and magnetic material is applied to model an electric vehicle equipped with a WPT charging system. With this configuration, compliance with the electromagnetic field safety standards can be achieved inside (passengers) or near (pedestrian) the car.

In this paper, a resonant inductive wireless power transfer link using a relay element is analyzed. Different problems of practical interest are considered and solved by modeling the link as a lossy two-port network. According to the two-port network formalism, the standard gain definition (i.e. the power, the available, and the transducer gains) are used for describing the network behavior. Firstly, the case of a link with given parameters is considered and the analytical expressions of the optimal terminating impedances for maximizing the link gains are derived. Later on, the case of a link with given source and load is analyzed and the possibility of maximizing the performance by acting either on the transmitting or on the receiving side is investigated. It is shown that by using a single relay element, it is not always possible to maximize all the figures of merit that could be of interest in the WPT context. Theoretical data are validated by comparisons with circuital simulation results.

New small unmanned air vehicles designated as micro air vehicles (MAVs) are increasingly attractive for research, environmental observation, and commercial purposes. As described herein, the feasibility of a system for wireless power transmission via microwaves for MAVs was investigated. For its light weight and flexibility, a textile-based rectenna was proposed for microwave wireless power transmission of MAVs. To investigate bending effects on radiation performance, a microstrip patch antenna with a 5.8 GHz left-hand circular polarization was developed on a textile substrate. The antenna return loss, 20 dB, increased slightly with the antenna bending angle. An axial ratio <3 dB was maintained when the antenna bend angle was <30°. A rectification circuit was formed on the back side felt with sandwiched copper foil as a ground plate. Its weight per unit area was 0.08 g/m2, with maximum rectification efficiency of 58% with 100 Ω load at 63 mW input power. The average and maximum total transmission efficiency using the 5.8 GHz multiple rectenna with a 2.45 GHz retrodirective system were, respectively, 0.44 and 0.60%. The possibility and feasibility of microwave power transmission system using the textile-based rectenna were evaluated.

In this contribution, the authors perform the design and show the experimental results relative to a prototype of a combined wireless power transfer (WPT)–power line communications (PLC) system, in which the WPT channel is interfaced to a PLC environment to allow data transfer when the cabled connection is no longer available. The main rationale behind this idea stays in the fact that PLC communication is now a popular choice to enable communications, for instance, in smart grids and in home automation, while WPT devices start to be available in the market (i.e. for mobile phones) and soon they will be a reality also for higher power (i.e. vehicle battery charging). In particular, theoretical insights about the requirements of the system are given; a two coils system has been implemented and a measurement campaign, together with simulations, show that the system is of great potentiality and could be used in applications where both wireless power and data transfer are needed (such as vehicles battery charging), achieving maximum power transfer and good data rate in order to transmit high-speed signals.

This paper presents a resonant inductive link for power and data transfer to a pulse generator implanted in the chest. The proposed link consists of two planar resonators and has been optimized for operating in the MedRadio band centered at 403 MHz. The wireless power/data link occurs between an external resonator operating in direct contact with the skin and a receiving resonator integrated in the silicone header of a pulse generator implanted in the chest. Numerical and experimental results are presented and discussed. From measurements performed by using minced pork to simulate the presence of human tissues, an efficiency of about 51% is demonstrated. The feasibility of using the proposed link for recharging the battery of the medical device in compliance with safety regulations is also verified and discussed.

This paper deals with the numerical evaluation of the magnetic field emitted by a wireless power system (WPT) in an electric vehicle (EV). The numerical investigation is carried out using a finite element method (FEM) code with a transition boundary condition (TBC) to model conductive materials. First, the TBC has been validated by comparison with the exact solution in simple computational domains with conductive panels at frequencies used in WPT automotive. Then, the FEM with TBC has been used to predict the field in an electric car assuming the chassis made by three different materials: steel, aluminum, and fiber composite. The magnetic field source is given by a WPT system with 7.7 kW power level operating at frequencies of 85 or 150 kHz. The calculated magnetic field has been compared with the International Commission on Non-Ionizing Radiation Protection (ICNIRP) reference level demonstrating compliance for an EV with metallic (steel or aluminum) chassis. On the contrary, a fiber composite chassis is much more penetrable by magnetic fields and the reference level is exceeded.