We have synthesized off-stoichiometric Ni40Cu10Mn35Ti15 all-d-metal Heusler alloy with a B2 cubic crystal structure by an arc melting process and investigated its structural, magnetic, electronic, thermal, and mechanical properties under the influence of a single-step thermal annealing. The compound exhibits an antiferromagnetic ordering accompanied by thermal hysteresis indicating a first-order magneto-structural transition. Curie–Weiss molecular field analysis reveals the presence of ferromagnetic interactions competing with long-range antiferromagnetic ordering. Thermal annealing leads to the appearance of a heat capacity sharp peak around antiferromagnetic transition. Electrical resistivity measurements display abrupt changes close to the magneto-structural transition revealing the strong coupling among spin, lattice, and charge degrees of freedom characteristic of a martensitic transition (MT). We have also evaluated its mechanical properties from microhardness measurements, and the results indicate that this alloy exhibits ductile behavior. The occurrence of MT associated with improved ductility is an essential combination for technological application as shape-memory alloys.

The study investigated novel wear and corrosion resistance of stainless steel and 316 stainless steel samples which were successfully prepared by laser melting deposition. Phase composition, microstructure, microhardness, wear resistance, and electrochemical corrosion resistance were studied. The experimental results showed that novel stainless steel was mainly composed of α-Fe and a few carbide phase (Cr, Fe)7C3. The microhardness of novel stainless steel was about 2.7 times greater than 316 stainless steel. Meanwhile, the specific wear rate of novel stainless steel and 316 stainless steel was 2.63 × 10−5 mm3/N m and 1.63 × 10−4 mm3/N m, respectively. The wear volume of 316 stainless steel was 6.19 times greater than novel stainless steel. The corrosion current and the corrosion potential of novel stainless steel and 316 stainless steel were 1.02 × 10−7 A/cm2 and 1.5 × 10−7 A/cm2, and −138.8 mV, −135.9 mV, respectively, in 3.5 wt% NaCl solution. Therefore, both microhardness and wear resistance of novel stainless steel were greatly improved, with high corrosion resistance.

This study aims to investigate the sliding wear behavior of Al0.4FeCrNiCox (x = 0, 0.25, 0.5, 1.0 mol) high-entropy alloys (HEAs) under oil lubricating conditions at room temperature. Phase and microstructural characterizations of HEAs are performed by utilizing X-ray photoelectron spectroscopy (XRD) and scanning electron microscope (SEM). The compressive yield strength of Al0.4FeCrNiCox (x = 0, 0.25, 0.5, 1.0 mol) HEAs is observed to decrease from 1169.35 to 257.63 MPa. Plastic deformation up to 75% is achieved in the case of Al0.4FeCrNiCox=1 HEA. The microhardness of HEA samples is found to decrease from 377 to 199 HV after the addition of cobalt content from x = 0 to 1.0 mol. Thermal analysis is performed using a differential scanning calorimeter. It is confirmed that Al0.4FeCrNiCox (x = 0, 0.25, 0.5, 1.0 mol) HEAs do not undergo any phase change up to 1000 °C. The specific wear rate of Al0.4FeCrNiCox=1 HEA is observed to be highest in all wear conditions. The worn surfaces were analyzed by SEM with attached energy-dispersive spectroscopy, 3D profiling, and X-ray photoelectron spectroscopy (XPS).

The alloyed layers were produced on Mg by heating the specimens in contact with pure Al powder or Al + Zn powder mixtures. The powder material acting as the source of diffusion elements was held under pressure during heating, and this led to the formation of thick, continuous layers in a short heating time (1 h). The layer formation process took place through partial melting at the substrate/powder interface. The Al-enriched layer was characterized by a eutectic structure composed of an Mg17Al12 intermetallic phase and a solid solution of Al in Mg. The Al/Zn-enriched layers produced from Al + 20% Zn and Al + 40% Zn powder mixtures consisted of Mg17(Al,Zn)12 and Mg5Al2Zn2 and a solid solution of Al and Zn in Mg. The alloyed layers had higher hardness and better wear resistance than the Mg substrate. The results of the polarization measurements show that the Al- and the Al/Zn-enriched layers provide a certain level of protection to Mg against corrosion.

The joint of dissimilar metals between Mo2FeB2-based cermets and 316L stainless steel was welded by gas tungsten arc welding with no fillers. The weldability was investigated by plate rigid restraint cracking test and transverse rupture strength was measured by the three-point bending test. Microstructure of the weld joint was studied with scanning electron microscope, energy-dispersive spectrometer, X-ray diffractometer and differential scanning calorimeter, etc. Corrosion behavior was investigated by the potentiodynamic polarization test. Results revealed that weld solidification cracking susceptibility existed in the fusion zone. Coarse irregular complex ternary boride phase (M3B2) and hypoeutectic microstructure were formed in weld metal (WM). In heat affected zone (HAZ), a small number of M3B2 grains dissolved into the γ-Fe based binder, with growth and coalescence of the remaining M3B2 grains. Microhardness of HAZ increased slightly and WM presented the highest microhardness in the whole joint. Besides, potentiodynamic polarization test showed that WM had a better corrosion resistance than Mo2FeB2-based cermets, which can be attributed to the higher Cr content and relatively homogenous Mo distribution.

Filament condition during hot-wire chemical vapor deposition conditions of multi-walled carbon nanotubes is a major concern for a stable deposition process. We report on the novel application of electron backscatter diffraction to characterize the carburization of tungsten filaments. During the synthesis, the W-filaments transform to W2C and WC. W-carbide growth followed a parabolic behavior corresponding to the diffusion of C as the rate-determining step. The grain size of W, W2C, and WC increases with longer exposure time and increasing filament temperature. The grain size of the recrystallizing W-core and W2C phase grows from the perimeter inwardly and this phenomenon is enhanced at filament temperatures in excess of 1,400°C. Cracks appear at filament temperatures >1,600°C, accompanied by a reduction in the filament operational lifetime. The increase of the W2C and recrystallized W-core grain size from the perimeter inwardly is ascribed to a thermal gradient within the filament, which in turn influences the hardness measurements and crack formation.

The objective of this study was to evaluate the influence of a cola soft drink (CSD) and coffee on the microhardness and surface roughness of composite resin. Fifty cavities were prepared on the vestibular surface of bovine incisors and restored with nanoparticulate resin. The teeth were divided into five groups (n = 10): group A (control), immersion in artificial saliva (AS) for 14 days; group B, immersion in coffee for 15 min (3×/day) for 7 days followed by immersion in AS for another 7 days; group C, immersion in CSD for 15 min (3×/day) for 7 days followed by immersion in AS for another 7 days; group D, immersion in AS for 7 days, immersion in coffee for 15 min (3×/day) for 7 days; group E, immersion in AS for 7 days, immersion in CSD for 15 min (3×/day) for 7 days. After the immersion periods the specimens were analyzed for their microhardness and surface roughness. The data were subjected to analysis of variance (ANOVA) followed by t-test with 5% significance. Group A presented the highest average microhardness and lowest surface roughness, so it was possible to conclude that the consumption of CSD and coffee alters the microhardness and surface roughness of new restorations.

Relationships between volume plasmon excitations and mechanical properties of various materials are considered. Based on systematic evaluation of available data, correlations between the volume plasmon energy, Ep, Young's modulus, Ym, bulk modulus, Bm, shear modulus, Gm, and microhardness, Hm, are established. The resulting correlations indicate that plasmon energies potentially can be used to predict and/or determine the local mechanical properties of technologically important materials, such as metal alloys, semiconductors, and ceramics at the nanometer level.

This paper presents experimental and analytical studies of AFM nanoindentation as a method to determine microhardness of hard thin films. Indentations are performed on Au, Si, and DLC using triangular pyramidal diamond probes to determine microhardness. We examined the effects of indentation force and three different methods to measure the indentation area (direct area measurement for a triangular indentation, size analysis of an inverted AFM image of the indentation, and prediction of area from indentation depth based on a tip shape function). The responses are indentation depth, projection area, and microhardness. Relationship of responses with indentation force is examined. At a low depth range, microhardness based on pyramidal shape function is erroneously higher than the other two methods. However, all three methods generally agree with each other when indentation force exceeds 16μN. Size analysis of inverted images gives more consistent microhardness with the least variability over the whole force (4∼30μN) or depth (0.5∼70 nm) range. Tip shape models are developed to predict microhardness. The ellipsoidal tip model is a good approximation at low depth ranges, while the pyramidal model works better for deeper indentations. The force vs area curves are also significantly nonlinear which can distort the hardness measurements.