This article presents the design and performance analysis of a printed microstrip ultra-wideband (UWB) antenna consisting of the slots in the ground plane and radiating patch. A meandered S-shaped slot has been introduced on the patch and an inverted U-shaped slot has been incorporated in the ground plane to realize the band-notch effect for WiMAX (3.2–3.8 GHz) and WLAN (5.1–5.8 GHz) bands respectively. The total dimension of the proposed design is 44 × 44 mm2. The fabricated antenna exhibits wide impedance bandwidth of 10 GHz (2.4–12.4 GHz), i.e., 135% of center frequency. The design prototype is fabricated, and the measured results have good agreement with simulated values. The effects of the slots have been analyzed by simulated surface current distribution. The designed antenna shows almost omnidirectional radiation patter and stable gain. The proposed hexagonal antenna may be suitable for UWB applications removing WiMAX and WLAN bands.

In this paper, a tri-band metamaterial (MTM) loaded compact monopole antenna is proposed. In the first step of design procedure, a rectangular monopole antenna is improved by replacing the corresponding rectangular patch with a ring resonator. As a result, the first obtained operating frequency is decreased from 2.95 to 2.46 GHz. Then, this operating frequency is reduced to 2.02 GHz utilizing an MTM geometry in the antenna structure. The geometry parameters of the proposed antenna are optimized to provide the applicability for 3G, WLAN, and WiMAX applications. The impedance bandwidths of 600, 1080, and 220 MHz are obtained at 2.02–2.62, 3.48–4.56, and 5.12–5.34 GHz, respectively. Moreover, the equivalent circuit of the proposed antenna has been extracted. The proposed equivalent circuit model is validated through a comparison with corresponding simulation results. The proposed antenna is compact, low profile, via-less, and provides easy fabrication. Considering the first resonance frequency, a compactness of 32% is achieved in comparison to the corresponding unloaded monopole antenna.

In this paper, a compact 4-port band-notched multi-input-multi-output (MIMO) antenna with asymmetric coplanar strip (ACS) feed is presented for ultra-wide band (UWB) applications. The MIMO antenna is comprised of four semi-elliptical radiators with ACS feed for UWB applications and it is printed on inexpensive FR4 substrate of size 48 × 52 mm2 with ɛr = 4.4 and 1.6 mm height. The impedance characteristics of the suggested MIMO antenna ranges from 2.7 to 11 GHz with a band-notched behavior from 3 to 4 GHz to reduce the interception with WiMAX applications, and the isolation level over the achieved band is more than 20 dB between any two adjacent elements. Moreover, the radiation pattern of the proposed UWB antenna is almost omnidirectional with an average realized gain of 3.5 dBi over the entire achieved frequency band. The proposed ACS-fed antenna is confirmed by fabricating and measuring it's impedance and radiation characteristics. Finally, good consistency between simulation and measured outcomes is obtained confirming the validity of the MIMO antenna for real-life UWB wireless systems.

Proposed is a wideband, low profile, fully flexible, and all-textile-based slotted triangular antenna loaded with a 2 × 2 textile-inspired artificial magnetic conductor to be worn on the wrist. The integrated antenna design is designed to cover the frequency band from 3.1 to 6.5 GHz. The integrated design has two main resonances, where the first one is at 3.5 GHz, which can serve the WiMAX communication standard, while the second is at 5.8 GHz, which can serve the Industrial, Scientific and Medical (ISM)-band. The incorporated textile materials are composed of the conductive and dielectric fabrics that are realized by ShieldIt and Felt, respectively. When simulated against the human model wrist, the integrated antenna design displayed a realized gain of 6.71 dBi and radiation efficiency of 79.1%, at 3.5 GHz. Furthermore, at 5.8 GHz, it displayed a realized gain of 7.82 dBi and total efficiency performances of 66.1%. Moreover, it accomplished very low SAR levels within the antenna frequency band. Averaged over 1 g of tissue, it exhibited maximum SAR levels of 3.28 × 10−6 and 9.37 × 10−7 W/kg at 3.5 and 5.8 GHz, respectively. For the bent scenarios, the integrated antenna design displayed robustness when bent at an angle of 20 and 40°. Finally, measurement results are illustrated and analyzed. Based on the presented results, the suggested all-textile integrated antenna design might be designated for integration with the wristband to monitor the user health conditions through many possible frequency channels.

In this research, a compact dual band-notched (DBN) super-wideband (SWB) coplanar waveguide-fed antenna with high bandwidth (BW) dimension ratio of 7427.4 has been presented. The proposed antenna covers a very wide frequency range from 2.8 to 40 GHz (BW ratio of 14.28:1) with |S11|<−10 dB. The overall antenna size is 20 × 14 × 1.6 mm3 which consists of an FR4 substrate with a dielectric constant of 4.4, a shovel-shaped radiating patch and the symmetric stair-shaped ground plane. The DBN characteristics are achieved by employing a pair of C-shaped and circular slots on its shovel-shaped radiating patch to reject the interferences caused by two WiMAX (3.7–4.7 GHz) and WLAN (5.7–6.4 GHz) bands. The notched frequency bands can be controlled by changing the radii of slots. The SWB property of the antenna is obtained by using a symmetric stair-shaped ground plane and also a shovel-shaped radiating patch. The measured results of the fabricated prototype in frequency-and time-domain are also presented and compared with the numerical results. The results indicate that the antenna has good performance over the entire operating BW (173.8%) which makes it very potential candidate for modern SWB applications.

A novel planar dual-band bow-tie slotted patch antenna backed by high-impedance surface (HIS) is designed at 2.5 and 3.5 GHz for wireless application. The antenna employs coplanar waveguide fed patch and bow-tie slot as radiating elements. The bow-tie slot enables dual-band operation for the antenna. The HIS is made asymmetric in design to make it polarization dependent. This polarization-dependent HIS is eventually designed to reflect circularly polarized waves from linearly polarized incident waves.

A multi-input multi-output (MIMO) antenna is designed and discussed for multi-band applications. The constituent antennas are composed of four L-shaped elements and a ground plane. When placed beside each other to form a MIMO antenna, a T-bar shaped parasitic structure is also embedded between the antennas on the backside of the substrate to increase the inter-element isolation. The triple-band performance of the antenna is observed at 2.15–2.73 GHz, 3.1–3.9 GHz, and 5.04–6 GHz. The isolation level of more than 20 is seen over the operating frequency range. The fabricated prototype of the MIMO antenna size is very compact (20 × 40 mm), printed on the FR4 substrate. Based on simulation and experimental results, the proposed design is useful for WiMAX and WLAN applications.

In this article, a multiband antenna for various wireless communications is proposed for WWAN, Bluetooth, WiMAX, WLAN, and Downlink satellite system. The antenna consists of a radiating patch and a rectangular ground plane with four L-shaped stubs which are embedded as side arms to obtain a resonating band for WWAN (1.9GHz), Bluetooth (2.4 GHz), WiMAX (2.5, 3.5, and 5.5 GHz), and WLAN (5.5 GHz) wireless systems and a C-shaped stub is etched on the radiating patch to obtain a higher WLAN band (2.4, 5.2, and 5.8 GHz) and a satellite downlink system (7.5 GHz). The proposed antenna exhibits circular polarization at WWAN band and linear polarization for remaining applications. Also, the proposed antenna exhibits an omnidirectional radiation pattern.

A compact planar ultra-wideband (UWB) antenna with WiMAX and WLAN notched band is presented in this paper. The presented antenna consists of a rectangular patch and slotted partial ground plane and fed by a microstrip feed line. The volumetric size of the antenna is 30 mm × 22 mm × 1.6 mm. Method of moment-based simulation technology is used to simulate and analyze the characteristics of the antenna. To generate two notch bands at WiMAX and WLAN, a pair of parasitic resonator is placed beneath the radiating patch. The presented antenna achieves an operating band (VSWR ≤2) ranging from 2.98 to 12 GHz with an average gain of 3.95 dBi along with considerable efficiency and symmetric radiation patterns. Moreover, the antenna exhibits two notch bands at 3.5 and 5.45 GHz and is able to avoid possible interference with pre-existing narrow band services. The proposed antenna is low cost and low profile and is modeled to be used as a transceiver in UWB communication applications.

This paper presents a hexa-band frequency reconfigurable planar antenna, printed on a 1.6 mm thicker FR 4 substrate and backed by a truncated ground plane. The given antenna operates in four different frequency modes, depending on the state of the two lumped element switches. The proposed antenna works at six frequencies, 2.10, 2.40, 3.35, 3.50, 5.28, and 5.97 GHz. These frequency bands are dedicated to useful wireless applications, including 3G Advanced (2.10 GHz), Wireless Fidelity (Wi-Fi) (2.40 GHz), WiMAX (3.35 GHz), WiMAX (3.5 GHz), WLAN (5.28 GHz) and fixed-satellite and mobile satellite services (5.97 GHz). Satisfactory gain of 1.96, 2.20, 2.671, 2.81, 3.80, and 3.88 dBi, efficiency of 92.5, 94.5, 94.56, 95.0, 93.8, and 97.0% and bandwidth of 332, 485, 1020, 1080, 512, and 465 MHz has been obtained at 2.10, 2.40, 3.35, 3.50, 5.28, and 5.97 GHz, respectively. The modeling and simulations are conducted in CST MWS (2014). The simulated reflection coefficient and radiation pattern are validated in antenna measurement facility. In addition, the specific absorption rate of the antenna on a flat section of human body is also studied. The antenna is compact, low profile, and vastly suitable for multi-band wireless devices.

In this study, a dual-wideband monopole antenna has been designed and developed for the universal mobile telecommunications system (UMTS), wireless local area network (WLAN), and worldwide interoperability for microwave access (WiMAX) applications. A novel approach integrating artificial bee colony (ABC) with the HyperLynx® 3D electromagnetic platform based on the method of moments has been employed to calculate the design parameters of the monopole antenna performance for the respective target frequencies and return loss. The proposed dual-wideband antenna operates in the dual-frequency ranges of 1.69–3.99 and 4.75–6.22 GHz applicable for the UMTS, WLAN, and WiMAX applications and it is fabricated on the flame resistant-4 substrate plate of 42 × 51 × 1.6 mm3. The performance of the presented monopole antenna is analyzed in terms of gain, radiation pattern, and s-parameter. The input reflection coefficient (S11) parameter and radiation pattern of the antenna are verified through the measurements. The measured values of the antenna parameters are found to match well within tolerable limits with the simulation results. The results illustrate that the presented dual-wideband monopole antenna obtained by using the ABC algorithm exhibits better performance in point of operating bands and s-parameter as compared with the multi-band antennas previously published in the literature.

In this paper, an asymmetric coplanar strip (ACS)-fed quad-band monopole antenna for the global positioning system (GPS), wireless local area network (WLAN), and worldwide interoperability for microwave access (WiMAX) applications is proposed. It is composed of an F-shaped monopole and a partial ground plane, which are both printed on one side of a low-cost FR4 substrate with a compact volume of 40 × 20 × 1.6 mm3. By cutting an open-ended Γ-shaped slot into the F-shaped monopole, four distinct resonant modes are successfully generated. The design process, especially the geometrical configuration of the critical Γ-shaped slot is studied in detail. The proposed antenna has been fabricated and experimental results show that the −10 dB impedance bandwidth can fully cover the 1.575-GHz GPS (1.57–1.59 GHz), 2.4/5.2/5.8-GHz WLAN (2.4–2.485, 5.15–5.35, and 5.725–5.825 GHz), and 2.5/3.5/5.5-GHz WiMAX (2.50–2.69, 3.30–3.70, and 5.25–5.85 GHz) applications with nearly omni-directional radiation patterns and satisfactory gains.

The design and analysis of meta-material inspired loaded monopole antenna for multiband operation are reported. The proposed antenna consists of multi resonators inspired from half mode composite right/left handed cells, which has a simple structure, compact size, and provides multiband functionalities. As a proof of concept, a triple band antenna covering all possible WiMAX operating bands, has been designed, fabricated, and characterized. The hosting monopole patch itself generates resonance for 3.3–3.8 GHz band, whereas the loaded metamaterial cells add extra resonance frequencies. The loading of two resonator cells introduces two extra resonances for 2.5–2.7 GHz and 5.3–5.9 GHz bands, respectively. The antenna's operating principle and design procedures with the aid of electromagnetic full wave simulation and experimental measurements are presented. The antenna has good omnidirectional patterns at all three bands. The monopole patch size is 13.5 × 6.5 mm2 and the whole antenna size (including the feed line) is 35 × 32 mm2. Compared with conventional single band microstrip patch radiator, the radiator size of this antenna is only 8.5% at 2.5 GHz, 17% at 3.5 GHz, and 37% at 5.5 GHz.

This paper presents the behavior of three iterations of a coplanar waveguide fed CANTOR Set fractal antenna. This kind of antennas allows having a broadband behavior and important gains. Also, the setup of slots allows having more lower resonant frequencies and therefore designing miniaturized antennas with good performances. The proposed antennas are suitable for 2.5/3.3/5/5.5 GHz worldwide interoperability for microwave access and for 2.4–2.5/4.9–5.9 GHz wireless local area networks applications. The simulations were performed in FEKO 6.3. The measurements were performed with Vector Network Analyzer HP 8719C.

A compact coplanar waveguide (CPW)-fed wideband metamaterial-inspired antenna is designed and developed in this paper. The proposed structure is an asymmetric structure in which three rectangular stubs are employed between signal patch and CPW ground plane. It is demonstrated that these stubs provides lumped parameters of conventional epsilon-negative transmission line (ENG-TL). As an advantage of these stubs proposed antenna operates on 1.67–2.76 GHz with −10 dB impedance bandwidth of 49.2%. The proposed antenna having small electrical size of 0.17λ0 × 0.35λ0 × 0.01λ0 at fo = 2.21 GHz. The simulated average gain and radiation efficiency of the proposed antenna is 1.61 dB and 96.33% respectively throughout the bandwidth. Properties such as smaller electrical size, simpler design, consistent radiation characteristics, and ease of fabrication are making this antenna suitable for GSM, WLAN/Wi-Fi, Bluetooth, and WiMAX applications.

A compact quad band slot antenna with high isolation suitable for multiple-input–multiple-output (MIMO) applications is developed. The quad bands are achieved by introducing slots in a modified, size reduced circular patch antenna. The single-antenna element consists of a substrate sandwiched between a modified circular patch with F shape slot, a feeder line and a via running between the radiating patch and the feeder line. The proposed design resonates at the frequencies of 1.8 GHz (1.7–1.88 GHz), 3.6 GHz (3.50–3.76 GHz), 5.4 GHz (5.25–5.38 GHz), and 7.2 GHz (7.15–7.35 GHz) covering the GSM II, WIMAX, wireless local area network (WLAN), and C-band applications, respectively. The independent tuning of frequency bands is achieved by varying the length of the slots. Orthogonally placed two- and four-element MIMO antenna system are fabricated, tested, and the measurement results are presented. The separation between each element is reduced to 0.085λ while introducing slotted and pulsed stubs to improve isolation between elements. A detailed analysis, including mutual coupling, low correlation, diversity gain, and total array reflection coefficient had been reported. The two- and four-element MIMO antennas achieved correlation as low as 0.005, mutual coupling ≤−15 dB, and diversity gain nearly 10 dB.

To restrict electromagnetic interference at WiMAX (3.3–3.7 GHz) and wireless local area network (WLAN) (5.15–5.825 GHz) bands operating within ultra wide bandwidth (UWB) band, a novel design of lamp-shaped UWB microstrip antenna with dual band-notched characteristics is presented. The proposed antenna is composed of a lamp-shaped radiating patch with two rectangular ground planes on both the sides of the radiator with the gap of 0.57 mm. To improve impedance mismatch at middle frequencies, two triangular strips one at each of the ground plane are added; whereas a rectangular slot is etched in the radiating patch to remove impedance mismatch at higher frequencies of the UWB band. Furthermore, an L-shaped slot in the radiator and two L-shaped slots in the ground plane are used to restrict electromagnetic interference (EMI) at WiMAX and WLAN bands, respectively, without affecting the electrical performance of the UWB antenna. Effects of the key parameters on the frequency range of the notched bands are also investigated. The proposed design shows a measured impedance bandwidth of 12.5 GHz (2.7–14.4 GHz), with the two band-notched bands of 3.0–3.9 and 4.9–5.8 GHz. The antenna is suitable to be integrated within the portable UWB devices without EMI interference at WiMAX and WLAN bands.

In this paper, a three layered stacked circularly polarized rectangular dual band microstrip antenna with a defected ground structure (DGS) and a feed network with stub (showing dual wideband characteristic) is designed, fabricated, and tested for WLAN, Zig bee, Wi-Max, and IMT band applications. The proposed antenna is fabricated on an FR4 substrate with dielectric constant (εr) of 4.4; tanδ of 0.0024 and a height of 1.57 mm.The antenna has a surface area of 4.8 × 4.1 cm2 and a total height of 5.1 mm. The designed antenna covers two wireless bands from 2.39 to 2.64GHz and 3.39–3.76 GHZ with impedance bandwidths (VSWR < 2) of 250 MHz (9% bandwidth centered at 2.515 GHz) and 370 MHz (10% bandwidth centered at 3.57 GHz), respectively. This antenna is capable of covering IEEE 802.11b/g/n standards of WLAN from 2.4 to 2.485 GHz, bluetooth applications from 2.4 to 2.483 GHz, ZigBee applications from 2.4 to 2.485 GHz, IEEE 802.16/ Wi-MaX applications from 3.4 to 3.69 GHz and international mobile telecommunications (IMT) band from 3.4 to 3.6 GHz. As the antenna is circularly polarized, the misalignment of the receiver with transmitter does not affect the performance of the system. The antenna designing was done using CST MWS V'10 and the prototype of the designed antenna was tested for the validation of S11 (dB) and gain results against the simulated ones experimentally. The proposed antenna shows a gain of 4.08 dBi at 2.5 GHz and a gain of 5.024 dBi at 3.51 GHz.

In this paper, a dual wideband microstrip antenna (MSA) has been presented for wireless local area networks (WLAN), worldwide interoperability for microwave access (Wi MaX) and U-NII band applications. The antenna is designed and simulated using CSTMWS V'10. The main goal of this paper is to get multi-frequency behavior by cutting resonant slots into the patch of the antenna and a wideband antenna behavior using an aperture coupled feeding method. The designed antenna has a semi-spiral G-shaped compact structure and an electromagnetically coupled feeding mechanism (aperture-coupled feeding). It is fabricated on an FR4 substrate with a dielectric constant of 4.4 and a dielectric loss tangent of 0.009. The testing of prototype antenna (to measure S11) is done using a vector network analyzer. The measured results are 80% matching to the simulated ones. The parametric study, simulation results, measured results, and applications of the MSA for WLAN, WiMAX, and the FCC unlicensed 5.2 GHz National Information Infrastructure (U-NII) bands are presented in the paper. The antenna shows a simulated gain of about 4.5 dB at the three wireless application bands.

This paper presents a multiple-input and multiple-output dual-element planar inverted-F antenna (PIFA) array for broadband operation covering the HIgh PERformance radio Local Area Network/2 (5.2 GHz/5.6 GHz), Wireless Local Area Network (5.2 GHz/5.8 GHz), and the Worldwide Interoperability for Microwave Access (5.5 GHz) bands for the compact wireless communication devices. The antenna dimension is reduced substantially with a miniature ground plane. The PIFA array provides a large bandwidth (670 MHz) and a high isolation between its ports less than −26 dB. The proposed antenna has been analyzed and designed with Ansoft HFSS v.11. Then a prototype was fabricated and tested for its performance in terms of bandwidth, S-parameters, and radiation pattern. A parametric study is made to analyze the effect of different PIFA parameters on the operating frequency and the S-parameters. The diversity performances are evaluated using computer simulation technology microwave studio (CSTMWS). The broadband performance and the high isolation are achieved in both simulation and measurement.