Six four-element balun topologies are introduced that enable complex impedance matching in addition to common-mode rejection. Design equations for these topologies are presented. Three of these networks are universal, while the other three are capable of performing only specific impedance transformations. Examples of these networks were designed and fabricated along with a traditional lattice balun network for an operating frequency of 300 MHz. These networks were verified through extensive electromagnetic simulations and by measuring the fabricated networks. The fabricated novel network examples were able to achieve common-mode rejection ratios above 20 dB, power wave reflection coefficients below −20 dB, and insertion losses of approximately 0.1 dB; these results were similar to or better than the performance of the fabricated traditional lattice balun. The design example networks also provided power matching and low insertion loss over a greater bandwidth compared to the fabricated traditional network. These networks will allow for the footprints of lumped-element balun circuitry to be reduced, which is particularly useful in integrated circuit design. These topologies are also expected to further increase radio-frequency (RF) circuit design flexibility by offering more alternative realizations.

This paper provides the details of a novel systematic design methodology for two-way in-phase filtering Gysel splitter/combiner networks with high selectivity, which finds application in high power amplifier modules. It simultaneously realizes a filtering function and a two-way splitter/combiner function. The proposed five-port filtering device, based on the Gysel topology, is transformed into a ring of coupled resonators. A rigorous coupling matrix describing the network is used to synthesize the integrated filtering and combining functions. This general network can be implemented in any of the available filter technologies. In this paper, a few design examples are provided, and a six-pole prototype utilizing compact combline coaxial resonators is demonstrated. The proposed design provides an integrated dual function module, reducing component counts and system complexity. A design was fabricated and tested demonstrating good experimental results.

This manuscript presents a novel design for an absorptive bandpass filter for mm-wave applications, specifically the commercial FR2 spectrum. Three bands have been selected to be properly input matched with only one of them being the passband, where the insertion loss is minimized. The proposed approach relies on a multiplexer topology implemented through microstrip lines and on thin-film manufacturing process on alumina to shrink the footprint. Cascades of half-wavelength C-shape open-ended resonators are exploited to create the matched bands and define the filter’s selectivity. The selected passband spans from 26.5 to 28.5 GHz, with a measured maximum insertion loss of 3.05 dB for a −3 dB fractional bandwidth of 7.3%. Two absorptive bands are realized to match signals at 24 and 32.25 GHz. The alumina die footprint is 5500 × 3440 µm2, compatible with immediate integration within a mm-wave lineup.

A wideband tunable balanced phase shifter is achieved by utilizing varactor-loaded coupled lines (VLCLs)-embedded multistage branch-line structure. The tunable phase shift with low in-band phase deviation is attributed to the regulation in phase shift of the VLCLs and the horizontal microstrip lines in series. The wideband differential-mode (DM) impedance matching and common-mode (CM) suppression are due to multiple DM transmission poles and CM transmission zeros, which are brought about by the cascade of VLCLs and a microstrip line with short-circuited stubs in the DM-equivalent circuit and open-circuited stubs in the CM-equivalent circuit, respectively. Compared with the state-of-the-art tunable balanced phase shifters, the proposed design not only has the advantages of wide operating bandwidth (BW) with low in-band phase deviation but also has low insertion loss and easily fabricated structure. Theoretical analysis and design procedure were conducted, resulting in a prototype covering the frequency of 1.8 GHz. This prototype offers a tunable phase shift capability ranging from 0° to 90°. The prototype exhibits an operating BW of 45%, with a maximum phase deviation of ±6°. It also achieves a 10 dB DM return loss and CM suppression, while maintaining a maximum insertion loss of 2.5 dB.

This paper presents a broadband Butler-based slant ±45° dual-polarized omni-directional antenna working at the frequency band of 1.69–2.69 GHz for extending wireless communication network capacity in the limited service size. The proposed antenna realizes a 360° full coverage with wider bandwidth in a compact cylinder and increases the network capacity to 6 × 6 MIMO instead of using three traditional 2 × 2 MIMO omni-directional antennas. Theoretical analysis, simulation, and fabrication are conducted to validate the idea of the proposed omni-directional antenna. The measured results show 46% bandwidth with 15 dB return loss, 2.2 dB azimuth null and 8.9–10.5 dBi gain for port-C with 0° phase increment, and 14.1 dB azimuth null and 9.6–10.6 dBi gain for port-L/R (left/right) with ±120° phase increment, respectively.

A new isolated out-of-phase filtering power divider/combiner with high selectivity is presented. Based on a single-layer microstrip, required coupling strength and phase difference are achieved by two pairs of three-line coupled feeding structures. To realize desired bandpass responses, a specific resonator is located between the input and output coupled structures. By connecting a half-wavelength transmission line which is centrally loaded with a grounded resistor between two output ports, high port-to-port isolation is attained. Based on the impedance matrix of coupled three-line structure, theoretical filtering responses are predicted with the specified bandwidth and return loss. For demonstration, a prototype is designed, fabricated, and tested. Both simulated and measured results are displayed to verify the design mechanism.

Full duplex (FD) could potentially double wireless communications capacity by allowing simultaneous transmission and reception on the same frequency channel. A single antenna architecture is proposed here based on a modified rat-race coupler to couple the transmit and receive paths to the antenna while providing a degree of isolation. To allow the self-interference cancellation (SiC) to be maximized, the rat-race coupler was made tuneable. This compensated for both the limited isolation of the rat race and self-interference caused by antenna mismatch. Tuneable operation was achieved by removing the fourth port of the rat race and inserting a variable attenuator and variable phase shifter into the loop. In simulation with a 50 Ω load on the antenna port, better than −65 dB narrowband SiC was achieved over the whole 2.45 GHz industrial, scientific and medical (ISM) band. Inserting the S-parameters of a commercially available sleeve dipole antenna into the simulation, better than −57 dB narrowband SiC could be tuned over the whole band. Practically, better than −58 dB narrowband tuneable SiC was achieved with a practical antenna. When excited with a 20 MHz Wi-Fi signal, −42 dB average SiC could be achieved with the antenna.

This paper presents wideband split-ring antenna arrays based on substrate integrated waveguide (SIW) for Ka-band (26.5–40 GHz) applications. The antenna array is fed by a 2.92 mm coaxial connector (K-connector) and the power is equally distributed to each split-ring resonator. The designed coplanar waveguide (CPW), SIW, CPW-to-SIW transition, coaxial-to-CPW transition, and two-stage SIW power divider are described in detail. By using a thin Rogers 6002 substrate with silver epoxy-filled vias, a transition prototype is designed, fabricated, and tested in a back-to-back configuration. A wideband split-ring resonator is developed as a single element and four possible arrangements of antenna arrays are introduced. By combining the designed components and routing paths, two full layouts of the antenna arrays with four split-ring resonators are addressed. As a demonstrator, a 2×2 antenna array prototype in a compact format is designed, fabricated, and tested. The fabricated antenna array achieves a measured directivity of 15.0 dBi with a fractional bandwidth of 23.0% centered at 30.5 GHz.

The spectral and energy characteristics of the tunable thin planar dielectric resonator with the movable metal mirror are researched. It is found that the high-Q HE-polarized whispering gallery modes (WGMs) are effectively excited in such a resonator by the dielectric waveguide. A mode set of the tunable thin planar dielectric resonator depends on the presence of an air gap in its design. Changing the height of the air gap affects the energy characteristics of the tunable thin planar dielectric resonators (DR). Shifting the resonant fields of WGMs from the dielectric disk to the air gap is the reason for this effect. It is shown that at certain heights of the air gap, increasing the unloaded Q-factor of the tunable thin planar DR and improving the excitation efficiency of WGMs in it is achieved.

This paper presents a simple topology of 180° hybrid coupler with non-interspersed inputs and outputs, as opposed to the conventional rat-race topology. Such hybrid coupler topologies with inputs located on one side and outputs at the opposite side simplify the design of signal routings and module packaging when integrated with other circuits and components. It also relaxes the necessity of using auxiliary compensating components such as tapers, jumpers, and crossovers. The proposed coupler topology is theoretically analyzed through a T-matrix approach. The analysis comes up with design equations and diagrams that help choose the structural parameters for the desired specification. The simplicity and also the immunity against intrinsic parasitic effects within the proposed topology make it an excellent candidate for operation over any RF and millimeter-wave frequency bands, for applications such as automotive radar or E-band backhaul radio. To this end, a coupler based on the proposed scheme is realized for operation over 77 GHz and assessed through on-wafer measurements. Good agreement of the measured results with the simulated and analytical counterparts demonstrates the superior performance of the proposed 180° hybrid coupler.

This paper reports a novel fourth-order quasi-elliptic bandpass filter (BPF) based on capacitive-loaded eighth-mode substrate integrated waveguide (CLEMSIW) cavities. The CLEMSIW cavity is constructed by the conventional eighth-mode SIW with two dielectric substrates and three metal layers; a metal via is employed to connect the middle and bottom metal layers. The middle metal layer achieves a large loading capacitance to shift the resonance frequency. The proposed filter is designed in a quadruple scheme, and two controllable finite-transmission zeros can be realized. For the demonstration, a prototype with a center frequency of 1 GHz and a fractional bandwidth of 10% was designed, fabricated, and measured. The measured results agree well with simulated ones. The proposed filter has advantages of ultra-compact size, high selectivity, and good stopband performances.

This paper presents a novel assessment method that minimizes test-fixture-induced errors in non-coaxial power combiner measurement by extending the port reduction method. This method involves terminating certain ports to acquire the scattering matrix of an N-port network from the scattering matrix measured at a reduced port order. The entire DUT scattering matrix is obtained from multiple scanning measurements, which are taken from partial coaxial accessible ports, based on a set of configurable terminating states. This advantage is leveraged to exclude a major portion of coaxial launch structures that would otherwise be incorporated in the conventional multiport test fixture. An analogous concept here is applied to measure a waveguide traveling-wave power combiner. A sandwiched twin structure, containing a divider/combiner pair with certain auxiliary through-type components cushioned between them, is utilized to assess the combiner characteristics. A theoretical framework of the proposed method was established to test its potential precision. Thereafter, an in-situ implementation was conducted to test its practical application on a traveling-wave combined amplifier prototype operating at the Q-band (33–39 GHz).

A compact transition between conductor-backed coplanar waveguide (CBCPW) and substrate integrated suspended line (SISL) is presented. Compared to the reported transitions from CBCPW to SISL, performance and compactness are improved. For demonstration purpose, a multilayer transition is designed and fabricated for operation up to 46 GHz. Experimental results, based on an electronic calibration and thru–reflect–line calibration allowing measurement in the 0.01–50 GHz frequency range, demonstrate an insertion loss of 0.59 ± 0.51 dB with a return loss of better than 10 dB in the 10 MHz to 46 GHz frequency range.

A power MOSFET-based push–pull configuration nanosecond-pulse generator has been designed, constructed, and characterized to permeabilize cells for biological and medical applications. The generator can deliver pulses with durations ranging from 80 ns up to 1 µs and pulse amplitudes up to 1.4 kV. The unit has been tested for in vitro experiments on a medulloblastoma cell line. Following the exposure of cells to 100, 200, and 300 ns electric field pulses, permeabilization tests were carried out, and viability tests were conducted to verify the performance of the generator. The maximum temperature rise of the biological load was also calculated based on Joule heating energy conservation and experimental validation. Our results indicate that the developed device has good capabilities to achieve well-controlled electro-manipulation in vitro.

A novel online antenna array calibration method is presented in this paper for estimating direction-of-arrival (DOA) in the case of uncorrelated and coherent signals with unknown gain-phase errors. Conventional calibration methods mainly consider incoherent signals for uniform linear arrays with gain-phase errors. The proposed method has better performance not only for uncorrelated signals but also for coherent signals. First, an on-grid sparse technique based on the covariance fitting criteria is reformulated aiming at gain-phase errors to obtain DOA and the corresponding source power, which is robust to coherent sources. Second, the gain-phase errors are estimated in the case of uncorrelated and coherent signals via introducing an exchange matrix as the pre-processing of a covariance matrix and then decomposing the eigenvalues of the covariance matrix. Those parameters estimate values converge to the real values by an alternate iteration process. The proposed method does not require the presence of calibration sources and previous calibration information unlike offline ways. Simulation results verify the effectiveness of the proposed method which outperforms the traditional approaches.

Design and development of 2 kW, 3 dB tandem hybrid coupler for the frequency range of 155–225 MHz has been presented in this paper. The developed 3 dB coupler is to be used in a prototype of Ion Cyclotron Resonance Frequency (ICRF) system of Tokamak, which has been developed to test the resilience of ICRF network during continuously variable RF load excursions. The 3 dB coupler divides the RF power between two antennae of the prototype and protects the RF source by coupling of reflected power to the isolated port. The developed coupler shows excellent coupling flatness of −3 ± 0.3 dB over 38% of fractional bandwidth and also provides voltage standing wave ratio (VSWR) <1.3, isolation better than 32 dB and return loss better than 25 dB in full band. The presented work establishes a technique which can be useful for the development of high-power hybrid coupler in the range of high frequency (HF), very high frequency (VHF) and ultra high frequency (UHF).

In this paper, a 3 dB H-plane substrate-integrated waveguide (SIW) power divider/combiner with improved isolation is reported. By adding two isolated ports into the Y-junction, it will perform like a multi-port coupler, so that the isolation between its dividing ports can be effectively improved as the newly-added ports are properly matched. To verify the availability and effectiveness of this concept, two prototypes, one is terminated by coaxial terminations and the other is loaded with lumped resistors, are developed. Their measured results are separately in good agreement with their corresponding simulations. Meanwhile, isolations better than 16 dB with fractional bandwidth (FBW) of 35 and 25% are achieved, respectively, as well as low phase and amplitude imbalances. Compared with some reported similar SIW power dividers, the proposed ones exhibit wider FBW with similar isolation, insertion loss, phase, and amplitude balance performance.

Tunable microwave devices will play an important role in future wireless systems, in which high-frequency bands, e.g. millimeter waves, will become promising, due to its huge spectrum availability. At such frequency bands, liquid crystals (LCs) exhibit low microwave loss, which is excellent compared with the other tuning elements. In this paper, LC-based microwave components are fabricated by using low temperature co-fired ceramic technology, allowing the integration of the LC into microwave structures. The first component, the amplitude tuner, controls the signal's amplitude by using the interference concept, which exhibits a tunable attenuation range from 11 dB to 30 dB at 30 GHz. The second component is a 3-pole tunable bandpass filter, which is realized by using a substrate integrated waveguide topology, enabling a device with comparatively high-quality factors (Q-factors). The measurement results show Q-factors in the range of 68 to 100 for a frequency tuning of 29.4–30.1 GHz, i.e. a tuning range of 700 MHz, accompanied by an insertion loss 2 dB to 4 dB.

This paper presents a miniaturized 3-dB branch-line coupler based on slow-wave microstrip transmission lines. The miniaturized coupler operating at 2.45 GHz is designed and implemented on a double-layer printed circuit board substrate with blind metallic vias embedded in the lower substrate layer providing the slow-wave effect. Based on this concept, a 43% size miniaturization is achieved as compared with a classical microstrip branch-line coupler prototype. The measured S parameters present a return loss of 25.5 dB and an average insertion loss equal to 0.05 dB at the operating frequency.

This paper presents an ultra-wideband coplanar waveguide (CPW)-to-asymmetric coplanar stripline (ACPS) transition based on aluminum nitride (AlN) substrate. The concepts of designing CPW, ACPS, and CPW-to-ACPS transition are explained. In order to suppress parasitic modes, vias going through AlN substrate are added along the ground traces. The signal trace is tapered out and chamfered to reduce the reflection caused by the termination of ground trace. The CPW-to-ACPS transition is designed, fabricated, and measured in a back-to-back configuration. The fabricated CPW-to-ACPS transition can provide a bandwidth of 165 GHz with an associated insertion loss of 3 dB.