A high-current electron-beam accelerator for pumping of a Xe2 lamp was developed. It is intended for injection of an electron beam into cylindrical gas cavity (diameter of 400 mm, length of 1600 mm, and the absolute pressure up to 3 bars). Two electron diodes in parallel are used in the accelerator. Each diode is connected to a linear transformer driver with vacuum insulation of a secondary turn. The next parameters of the accelerator have been obtained: diode voltage — 550–600 kV, diode current — 276–230 kA, current rise time — 160 ns, maximum power of the electron beam — 130 GW, pulse width on half maximum — 160 ns, electron beam energy at power level not less than half of maximum value — 20 kJ. The total energy of electrons, which pass through a 40 µm Ti foil into the Xe cell, is 8–9 kJ in the 150–160 ns pulse (full width at half maximum) mean specific power of energy input into gas cavity is about 330 kW/cm3. Design of the accelerator and test results are presented and discussed in this paper.

Technique of a linear transformer allows now to build the generators of high power nanosecond pulses with the current rise time of ~100 ns without intermediate power compression stages. This technique is being examined for use in high current high voltage pulsed accelerators. Plasma-filled diode has several advantages over standard vacuum diode that allow to improve the accelerators parameters. In this paper, plasma-filled diode experiments are described on generation of e-beam in the linear transformer accelerator. Possibility of use in the diode of isolated parallel plasma channels has been proven for the e-beam generation with cross-sectional area up to 50 cm2. The beam with current of 100 kA at voltage more than 400 kV was generated in the plasma-filled diode. Energy transmission efficiency from primary storage into a beam is about 54%.

Linear transformer driver (LTD) technology is actively developed at the Institute of High Current Electronics in Tomsk, Russia. This technology is being examined for use in high current high voltage pulsed accelerators. Recent development of high voltage low inductance capacitors and low inductance switches enabled to achieve ~100 ns rise time of the LTD output pulse. This technique allows one to eliminate intermediate pulse forming sections, used in the present accelerator technology, which would keep the footprint of an LTD accelerator small. LTD based drivers are currently considered for many applications, including future very high current Z-pinch drivers for inertial confinement fusion, medium current drivers with adjustable pulse length for isentropic compression experiments, and finally relatively low current accelerators for radiography and X-pinches. In this article, we present the design and test results for a new LTD stage, that operates at 100 kV charging voltage. Current amplitude up to 850 kA with ~140 ns rise time was obtained on a 0.05 Ω load. Stack of the LTD stages can be easily assembled in series or in parallel, thus providing voltage or current multiplication, respectively. Design of multi-mega-volt and multi-mega-ampere generators becomes straightforward with the LTD technology.

A high-current accelerator for pumping of the 200-L excimer laser is developed, providing electron energy of 550 keV, a diode current of 320 kA, and an e-beam current of 250 kA. The high-voltage part of the accelerator consists of two linear transformers with a stored energy of 98 kJ. To reduce the influence of the self-magnetic field on e-beam formation, the vacuum diode is divided into six separate magnetically isolated diodes.

Primary storages based on a linear transformer scheme were developed long ago. In this scheme, the secondary turn only has to be insulated from the high output voltage. Seven years ago at the High Current Electronics Institute (HCEI) a primary storage based on a linear transformer scheme and called the Linear Transformer Driver (LTD) stage was designed. In LTD stages, the primary turn, the storage capacitors with the switches, the core, and the outer conductor of the secondary turn are integrated into the stage cavity representing one separate building block of the primary storage. The body of the LTD cavity keeps ground potential during the shot allowing us to assemble them in series or in parallel depending on load requirements. Such flexibility of the storage structure and high output power of the LTD stages allows us to replace for some applications the traditional water line technology with LTD-based primary storages that are connected directly to the load (Direct Drive Scheme—DDS). In this article, we present the design of several LTD stages developed at HCEI and give examples of high-power energy storages produced by using the LTD technology.