For forthcoming wireless applications, a small and highly decoupled complementary split ring resonators (CSRR)–loaded co-planar waveguide (CPW)–fed antenna for dual-band applications is investigated. The low-profile antenna consists of a CSRR-loaded rectangular radiating element with a truncated bottom, giving a wideband performance over the frequency ranges of 5.28–5.52 GHz and 6–7.2 GHz. The antenna has been printed on a widely used FR4 substrate measuring 7.5 × 10.5 × 1.6 mm3 in volume. This research’s suggested antenna is turned into a 4 × 4 multi input multi output (MIMO) construction using a 25 × 25 mm2 printed circuit board. Individual antennas were isolated by nearly 20 dB without using a decoupling device. The antenna has been built, and the measured and simulated results correspond well. Computing envelope correlation coefficient (ECC), channel capacity (CC), and channel capacity loss (CCL) further validates the antenna’s performance (−). The antenna has an overall gain of around 2.54 dBi and a radiation efficiency of approximately 89% throughout the relevant spectral range, which is much better for wireless applications. The suggested antenna’s omnidirectional emission pattern makes it a potential contender for future wireless and cellular applications.

In this paper, a ring patch antenna with 1 GHz of bandwidth and three resonances is designed for the RF energy harvesting application. Two complementary split-ring resonators (CSRR) is etched out from the patch, designed at 6.8 GHz, near feed to enhance the bandwidth from 267 MHz to 1 GHz. Due to the introduction of CSRR, two additional resonances at 6.4 and 7.4 GHz are obtained with gain 5.5 and 0.2 dB respectively. The gains at 6.8 and 7.4 GHz are enhanced to 8.3 and 2 dB respectively by cascaded circular mushroom electromagnetic bandgap structures (EBGs) with circular symmetry designed around the antenna. This ring patch antenna with cascaded EBG is integrated with a rectifier circuit based on voltage doubler topology (rectenna). The results of the rectenna show that, for an input power of 7 dBm to the rectifier circuit, a DC output voltage of 1.2 V with a power conversion efficiency of 40% is achieved.

In this paper, non-uniform meandered line shunt capacitive RF-MEMS switch is presented at an elliptical patch etched with a split-ring resonator (SRR) for satellite communication applications. The non-uniform meander line shunt capacitive is a fixed-fixed type of RF-MEMS switch that is introduced in this model antenna. The proposed antenna design is resonated at 10.46 GHz with the return loss of −37.6 dB. The performance evolution of the proposed antenna design is evaluated with and without integrated RF-MEMS switch on the proposed antenna SRR. It is observed that the proposed model at the ON-state switch resonates at 10.57 GHz frequency with the return loss of −30 dB. Similarly, at the OFF-state switch, it resonates at 10.53 GHz frequency with the return loss of −43 dB. Al3N4 (aluminum nitride) is used for the switch as a dielectric material, hence the switch attains higher isolation. The actuation voltage of 7.9 V is required for the switch to actuate from ON to OFF state. The switch attains minimum insertion and return loss which is discussed in further sections. The proposed antenna is fabricated and tested by a vector network analyzer; there is a good agreement between the simulated and measured results.

This paper proposes a novel wideband to concurrent tri-band frequency reconfigurable microstrip antenna. The frequency reconfiguration is achieved by using a pair of PIN diodes in the antenna feed line to switch the antenna either in wideband mode or in concurrent tri-band mode. In order to improve the bandwidth and gain of the antenna for wideband operation, the properties of J-K inverter and split ring resonators are exploited. To demonstrate the versatility of this concept a prototype is fabricated and tested here. The tested results in wideband mode shows that the proposed antenna operates from 3.58 to –3.82 GHz, which is 4.08 times larger than the bandwidth of a simple microstrip patch antenna. In the concurrent tri-band mode frequency tuning is done by microstrip open stub at 1.5 GHz, 1.9 GHz, and 3.5 GHz. Gain of the proposed antenna is better than 2.7 dB in wideband mode and 2.7 dB in concurrent tri-band mode.