The focused ion beam (FIB) tool has been successfully used as both a stand alone analytical instrument and a means to prepare specimens for subsequent analysis by SEM, TEM, SIMS, XPS, and AUGER. In this work, special emphasis is given to TEM specimen preparation by the FIB lift-out technique. The fundamental ion/solid interactions that govern the FIB milling process are examined and discussed with respect to the preparation of electron transparent membranes. TRIM, a Monte Carlo simulation code, is used to physically model variables that influence FIB sputtering behavior. The results of such computer generated models are compared with empirical observations in a number of materials processed with an FEI 611 FIB workstation. The roles of incident ion attack angle, beam current, trench geometry, raster pattern, and target-material-dependent removal rates are considered. These interrelationships are used to explain observed phenomena and predict expected milling behaviors, thus increasing the potential for the FIB to be used more efficiently with reproducible results.

In variable pressure scanning electron microscopy (VPSEM) the current data suggests that considerable caution is required in the interpretation of X-ray data from nonconductive samples, depending on the operating conditions. This article reviews some of the documented approaches and presents data that illustrate the nature and magnitude of the effects of charge above, on, and in the sample on the detected X-ray emissions from the sample and from elsewhere within the VPSEM specimen chamber. The collection of reliable and reproducible X-ray data has been found to require relatively high specimen chamber gas pressures, at the upper end of or beyond the available pressures for most VPSEMs. It is also shown that sample characteristics, including composition, strongly influence local charge effects, which can significantly affect the primary electron landing energy and consequently the resultant emitted X-ray signal under low pressure environments.

Automated three-dimensional (3-D) image analysis methods are presented for tracing of dye-injected neurons imaged by fluorescence confocal microscopy and HRP-stained neurons imaged by transmitted-light brightfield microscopy. An improved algorithm for adaptive 3-D skeletonization of noisy images enables the tracing. This algorithm operates by performing connectivity testing over large N × N × N voxel neighborhoods exploiting the sparseness of the structures of interest, robust surface detection that improves upon classical vacant neighbor schemes, improved handling of process ends or tips based on shape collapse prevention, and thickness-adaptive thinning. The confocal image stacks were skeletonized directly. The brightfield stacks required 3-D deconvolution. The results of skeletonization were analyzed to extract a graph representation. Topological and metric analyses can be carried out using this representation. A semiautomatic method was developed for reconnection of dendritic fragments that are disconnected due to insufficient dye penetration, an imaging deficiency, or skeletonization errors.

Current X-ray diffraction techniques intended for “ideally imperfect” specimens provide structure factors only on a relative scale and ever-present multiple scattering in strong low-angle Bragg reflections is difficult to correct. Multiple scattering is implicit in the quantitative convergent beam electron diffraction (QCBED) method, which provides absolutely scaled structure factors. Conventional single crystal X-ray diffraction has proved adequate in softer materials where crystal perfection is limited. In hard materials, the highly perfect nature of the crystals is often a difficulty, due to the inadequacy of the conventional corrections for multiple scattering (extinction corrections). The present study on α-Al2O3 exploits the complementarity of synchrotron X-ray measurements for weak and medium intensities and QCBED measurement of the strong low-angle reflections. Two-dimensional near zone axis QCBED data from different crystals at various accelerating voltages, thicknesses, and orientations have been matched using Bloch-wave and multislice methods. The reproducibility of QCBED data is better than 0.5%. The low-angle strong QCBED structure factors were combined with middle and high-angle extinction-free data from synchrotron X-ray diffraction measurements. Static deformation charge density maps for α-Al2O3 have been calculated from a multipole expansion model refined using the combined QCBED and X-ray data.

The boundary parameters between contacting spherical bcc-Fe particles have been characterized with the Large Angle Convergent Beam Electron Diffraction (LACBED) technique. The average accuracy of measurements can reach 0.07°. The rotation parameters are interpreted using matrix algebra and evaluated according to the CSL model. The deviation between the experimental results and the reference misorientations given in the CSL model is determined. It is possible to reveal preferential misorientations between irregularly shaped particles with a size less than 100 nm. The method can be applied to nanoparticles and nanocrystalline materials with a wide range of grain orientations, and it is possible to modify it into an automatic method for TEM measurements.

Angiogenesis, a biologic process whereby endothelial cells divide and migrate to form new blood vessels, is a key step in tumor growth, invasion, and metastasis. In the present study, we investigated the differences in angioarchitecture between two different tumors induced by cloned cell lines (MT-8 and MT-9), derived from a transplantable rat malignant fibrous histiocytoma, by scanning electron microscopy of vascular corrosion casts. During a 3-week observation period after implantation, the growth of MT-8 tumors appeared to be faster than that of MT-9 tumors. Histologically, MT-8 tumors were of the uniformly undifferentiated sarcoma type arranged in characteristic organoid structures, and MT-9 tumors showed a storiform growth pattern. In MT-8 tumors, neovascularization occurred by sprouting at postimplantation (PI) week 1, and the newly formed capillaries gradually became more tortuous. In MT-9 tumors, at PI week 1, the corrosion casts of newly formed capillaries mainly showed a wavy course but no fingerlike outgrowths of capillaries were seen. At PI weeks 2 and 3, the sprouting was seen specifically in MT-9 tumors, forming basketlike structures and glomeruloid structures of capillaries. These results indicate that angiogenesis or angioarchitecture of MT-8 tumors is different from that of MT-9 tumors, depending on the differences in their tumor histology and by the features like absence or presence of basketlike structures and glomeruloid structures of capillaries.

Microscopy has played a critical role in first identifying and then defining the role of lysosomes in formation of atherosclerotic foam cells. We review the evidence implicating lysosomal lipid accumulation as a factor in the pathogenesis of atherosclerosis with reference to the role of microscopy. In addition, we explore mechanisms by which lysosomal lipid engorgement occurs. Low density lipoproteins which have become modified are the major source of lipid for foam cell formation. These altered lipoproteins are taken into the cell via receptor-mediated endocytosis and delivered to lysosomes. Under normal conditions, lipids from these lipoproteins are metabolized and do not accumulate in lysosomes. In the atherosclerotic foam cell, this normal metabolism is inhibited so that cholesterol and cholesteryl esters accumulate in lysosomes. Studies of cultured cells incubated with modified lipoproteins suggests this abnormal metabolism occurs in two steps. Initially, hydrolysis of lipoprotein cholesteryl esters occurs normally, but the resultant free cholesterol cannot exit the lysosome. Further lysosomal cholesterol accumulation inhibits hydrolysis, producing a mixture of cholesterol and cholesteryl esters within swollen lysosomes. Various lipoprotein modifications can produce this lysosomal engorgement in vitro and it remains to be seen which modifications are most important in vivo.

Human ovarian carcinoma cells (MDAH 2774) were treated with sodium ascorbate (VC), menadione (VK3), or with a VC:VK3 combination for 1 h and then studied using light microscopy (LM) and scanning (SEM) and transmission electron (TEM) microscopy. Plasma membrane damage (blisters and blebs, hairy aspect) results from vitamin C (VC) treatment, while cytoskeletal damage and self-morsellation are caused by vitamin K3 (VK3) treatment. VC:VK3-treated cells exhibit exacerbated injuries characteristic of both VC and VK3 treatment as well as a significant decrease in cell diameters from 20–35 μm for control cells to 7–12 μm for VC:VK3 treatment. Moreover, after a 1-h exposure to the vitamin combination, autoschizis (43%), apoptosis (3%), and oncosis (1.9%) are observed at the percentages indicated. All cellular changes associated with autoschizis observed with SEM were confirmed by LM and TEM observations and are consistent with cell death by autoschizis: decrease in cell size, cytoplasmic self-excisions, degradation of the nucleus and nucleolus without formation of apoptotic bodies and, ultimately, karyorrhexis and karyolysis. These results also suggest that the vitamin combination may find clinical use in the treatment of ovarian cancer.

The development of Leydig cells in mammals has been widely described as a biphasic pattern with two temporally mature Leydig cell populations, fetal stage followed by the adult generation beginning at puberty. In the present study, mouse Leydig cells were examined for apoptosis during postnatal testis development using electron microscopy and in situ DNA fragmentation by terminal deoxynucleotidyl transferase staining (TdT). Both the morphological study and the DNA fragmentation analysis showed that cellular death by apoptosis did not occur in Leydig cells during the neonatal, prepubertal, puberty, and adult periods. From these results, we suggest that the remaining fetal Leydig cells in the neonatal testis are associated with the involution or degeneration processes. In contrast, in the prepubertal and puberty stages, fragmentation of apoptotic DNA was detected in germ cells present in some seminiferous tubules.

Aromatic hydrocarbon (perylene, coronene) and tetracontane films are shown to produce useful convergent-beam electron diffraction (CBED) patterns under low-dose and low-temperature conditions. These were obtained using a Zeiss LEO-921 electron microscope with an omega energy filter at liquid helium and nitrogen temperatures. The usefulness of patterns showing CBED disks of constant intensity (“blank disks,” indicating kinematic scattering) for structure analysis is investigated, with the aim of avoiding film-bending artifacts. Using CBED patterns from thicker areas, sample thickness was experimentally determined using either two-beam or three-beam patterns. Koehler mode illumination (a new form of SAD pattern offering smaller areas) was also used, and the possibility of obtaining structure factor moduli using the kinematic and two-beam approximations was investigated by comparing measured diffraction intensities with experimental ones for these known structures. The commonly used approximation |F| ∼ Ig (intended to account for bending) was found to be a worse approximation than the two-beam approximation with well-defined excitation error for these microdiffraction experiments. A new multiwavelength method of retrieving structure factor moduli and thickness from microdiffraction patterns using two-beam theory is demonstrated for tetracontane.

Opening Reception, Sunday, August 3, 2003: The Institute of Texan Culture 6:30 PM to 10:00 PM

CIASEM Fiesta, Wednesday, August 6, 2003, Villita Assembly Building 8:00 PM to 11:30 PM

Spouses Program

Golf Tournament, Sunday morning, August 3, 2003

The length scales on which materials microstructures are being formed, grown, and even designed are becoming increasingly small and increasingly three-dimensional. For such complex structures two-dimensional transmission electron microscopy (TEM) analysis is often inadequate and occasionally misleading. One approach to this problem is the modification of electron tomography techniques, developed for structural biology, for use in materials science. Energy-Filtered (EF) TEM elemental distribution images approximate to true projections of structure, and, as such, can be used to reconstruct the three-dimensional distribution of chemical species. A sample holder has been modified to allow the high tilt (±60°) required for tomography and a semiautomatic acquisition script designed to manage energy-loss acquisition. Tilt series data sets have been acquired from two widely different experimental systems, Cr carbides in 316 stainless steel and magnetite nanocrystals in magnetotactic bacteria, demonstrating single- and multiple-element tomography. It is shown that both elemental maps and jump-ratio images are suitable for reconstruction, despite the effects of diffraction contrast in the former and thickness changes in the latter. It is concluded that the image contrast, signal, and signal-to-noise ratio (SNR) are key to the achievable reconstruction quality and, as such, the technique may be of limited value for high energy loss/small inelastic cross section edges.

The article compares the relative stability of MCM-41 and related mesoporous materials in electron beam at an accelerating voltage of 100–300 kV. The work encountered in electron microscopy presents a comparison with similar research that has been carried out on nonporous and microporous silicates, especially α-quartz and zeolite Y. The trends in stability are analyzed, classifying the effects of sample preparation, organic and inorganic moieties, and electron accelerating voltage on beam stability. A higher synthesis temperature, the use of an acid catalyst in the synthesis, and the presence of additional organic or inorganic material within the channels were all found to stabilize these materials. The dose required to completely disrupt the structure increased with accelerating voltage for nearly all samples, suggesting a primarily radiolytic damage mechanism. The exception, MCM-41 containing nanometer-sized titania particles in its channels, was found to be almost insensitive to accelerating voltage.

At present, mechanisms by which specific structural and mechanical properties of the three-dimensional extracellular matrix microenvironment influence cell behavior are not known. Lack of such knowledge precludes formulation of engineered scaffolds or tissue constructs that would deliver specific growth-inductive signals required for improved tissue restoration. This article describes a new mechanical loading–imaging technique that allows investigations of structural–mechanical properties of biomaterials as well as the structural–mechanical basis of cell–scaffold interactions at a microscopic level and in three dimensions. The technique is based upon the integration of a modified, miniature mechanical loading instrument with a confocal microscope. Confocal microscopy is conducted in a reflection and/or fluorescence mode for selective visualization of load-induced changes to the scaffold and any resident cells, while maintaining each specimen in a “live,” fully hydrated state. This innovative technique offers several advantages over current biomechanics methodologies, including simultaneous visualization of scaffold and/or cell microstructure in three dimensions during mechanical loading; quantification of macroscopic mechanical parameters including true stress and strain; and the ability to perform multiple analyses on the same specimen. This technique was used to determine the structural–mechanical properties of three very different biological materials: a reconstituted collagen matrix, a tissue-derived biomaterial, and a tissue construct representing cells and matrix.

As high-resolution biological transmission electron microscopy (TEM) has increased in popularity over recent years, the volume of data and number of projects underway has risen dramatically. A robust tool for effective data management is essential to efficiently process large data sets and extract maximum information from the available data. We present the Electron Microscopy Electronic Notebook (EMEN), a portable, object-oriented, web-based tool for TEM data archival and project management. EMEN has several unique features. First, the database is logically organized and annotated so multiple collaborators at different geographical locations can easily access and interpret the data without assistance. Second, the database was designed to provide flexibility to the user, so it can be used much as a lab notebook would be, while maintaining a structure suitable for data mining and direct interaction with data-processing software. Finally, as an object-oriented database, the database structure is dynamic and can be easily extended to incorporate information not defined in the original database specification.