The identification and accurate characterization of discrete grains of rare minerals in sulfide base-metal ores is usually a cumbersome procedure due to the small grain sizes (typically <10 μm) and complex mineral assemblages in the material. In this article, a new strategy for finding and identifying indium minerals, and quantifying their composition and abundance is presented, making use of mineral liberation analysis (MLA) and electron probe microanalysis (EPMA). The method was successfully applied to polymetallic massive sulfide ores from the Neves-Corvo deposit in Portugal. The presence of roquesite and sakuraiite could be systematically detected, their concentration quantified by MLA measurements, and their identity later confirmed by EPMA analyses. Based on these results, an almost complete indium deportment could be obtained for the studied samples. This validates the approach taken, combining automated mineralogy data with electron microprobe analysis. A similar approach could be used to find minerals of other common minor and trace elements in complex base-metal sulfide ores, for example Se, Ge, Sb, or Ag, thus permitting the targeted development of resource technologies suitable for by-product recovery.

Soft X-ray spectro-tomography provides three-dimensional (3D) chemical mapping based on natural X-ray absorption properties. Since radiation damage is intrinsic to X-ray absorption, it is important to find ways to maximize signal within a given dose. For tomography, using the smallest number of tilt series images that gives a faithful reconstruction is one such method. Compressed sensing (CS) methods have relatively recently been applied to tomographic reconstruction algorithms, providing faithful 3D reconstructions with a much smaller number of projection images than when conventional reconstruction methods are used. Here, CS is applied in the context of scanning transmission X-ray microscopy tomography. Reconstructions by weighted back-projection, the simultaneous iterative reconstruction technique, and CS are compared. The effects of varying tilt angle increment and angular range for the tomographic reconstructions are examined. Optimization of the regularization parameter in the CS reconstruction is explored and discussed. The comparisons show that CS can provide improved reconstruction fidelity relative to weighted back-projection and simultaneous iterative reconstruction techniques, with increasingly pronounced advantages as the angular sampling is reduced. In particular, missing wedge artifacts are significantly reduced and there is enhanced recovery of sharp edges. Examples of using CS for low-dose scanning transmission X-ray microscopy spectroscopic tomography are presented.

Supported lipid bilayer systems were evaluated following various experimental procedures in an effort to determine their appropriateness for visualization using total internal reflection fluorescence (TIRF) microscopy. The incorporation and distribution of Texas Red® 1,2-dihexadecanoyl-sn-glycero-3-phosphoethanolamine (TR-DHPE) was studied when incorporated into bilayers of variable lipid composition using different forms of mechanical shearing. Results showed that 0.8 mol% TR-DHPE provides the most optimum TIRF images. At this concentration, a sufficient level of photostability can be achieved without an undesirable increase in TR-DHPE aggregates caused by excess probe molecules. Solutions composed of a 3:1 molar ratio of DOPC:DPPC with 0.8 mol% TR-DHPE produce bilayers that consistently display clear, distinct, rounded domains, whereas other lipid compositions did not. This optimum phase separation appears to be influenced by an increase in mechanical shearing during the vesicle formation process, when the lipid solutions were exposed to sonication and extrusion processes. The combination of a sonication and extrusion process also helped with eliminating the presence of TR-DHPE aggregates within the model membranes. It was also shown that bilayers formed on conditioned glass, placed on a slide, produced more highly detailed bilayers in which distinct lipid phase separation could be optimally visualized using TIRF microscopy.

This paper reports on the substantial improvement of specimen quality by use of a low voltage (0.05 to ~1 keV), small diameter (~1 μm), argon ion beam following initial preparation using conventional broad-beam ion milling or focused ion beam. The specimens show significant reductions in the amorphous layer thickness and implanted artifacts. The targeted ion milling controls the specimen thickness according to the needs of advanced aberration-corrected and/or analytical transmission electron microscopy applications.

Correlative microscopy approaches offer synergistic solutions to many research problems. One such combination, that has been studied in limited detail, is the use of atom probe tomography (APT) and transmission Kikuchi diffraction (TKD) on the same tip specimen. By combining these two powerful microscopy techniques, the microstructure of important engineering alloys can be studied in greater detail. For the first time, the accuracy of crystallographic measurements made using APT will be independently verified using TKD. Experimental data from two atom probe tips, one a nanocrystalline Al–0.5Ag alloy specimen collected on a straight flight-path atom probe and the other a high purity Mo specimen collected on a reflectron-fitted instrument, will be compared. We find that the average minimum misorientation angle, calculated from calibrated atom probe reconstructions with two different pole combinations, deviate 0.7° and 1.4°, respectively, from the TKD results. The type of atom probe and experimental conditions appear to have some impact on this accuracy and the reconstruction and measurement procedures are likely to contribute further to degradation in angular resolution. The challenges and implications of this correlative approach will also be discussed.

The potential of the application of an X-ray excited optical luminescence (XEOL) analyzer and portable analyzers, composed of a cathodoluminescence (CL) spectrometer and electron probe microanalyzer (EPMA), to the on-line and on-site analysis of nonmetallic inclusions in steel is investigated as the first step leading to their practical use. MgAl2O4 spinel and Al2O3 particles were identified by capturing the luminescence as a result of irradiating X-rays in air on a model sample containing MgAl2O4 spinel and Al2O3 particles in the size range from 20 to 50 μm. We were able to identify the MgAl2O4 spinel and Al2O3 particles in the same sample using the portable CL spectrometer. In both cases, not all of the particles in the sample were identified because the luminescence intensities of the smaller Al2O3 in particular were too low to detect. These problems could be solved by using an X-ray tube with a higher power and increasing the beam current of the portable CL spectrometer. The portable EPMA distinguished between the MgAl2O4 spinel and Al2O3 particles whose luminescent colors were detected using the portable CL spectrometer. Therefore, XEOL analysis has potential for the on-line analysis of nonmetallic inclusions in steel if we have information on the luminescence colors of the nonmetallic inclusions. In addition, a portable EPMA–CL analyzer would be able to perform on-site analysis of nonmetallic inclusions in steel.

The use of in vivo X-ray microcomputed tomography (μCT) to study plant root systems has become routine, but is often hampered by poor contrast between roots, soil, soil water, and soil organic matter. In clinical radiology, imaging of poorly contrasting regions is frequently aided by the use of radio-opaque contrast media. In this study, we present evidence for the utility of iodinated contrast media (ICM) in the study of plant root systems using μCT. Different dilutions of an ionic and nonionic ICM (Gastrografin 370 and Niopam 300) were perfused into the aerial vasculature of juvenile pea plants via a leaf flap (Pisum sativum). The root systems were imaged via μCT, and a variety of image-processing approaches used to quantify and compare the magnitude of the contrast enhancement between different regions. Though the treatment did not appear to significantly aid extraction of full root system architectures from the surrounding soil, it did allow the xylem and phloem units of seminal roots and the vascular morphology within rhizobial nodules to be clearly visualized. The nonionic, low-osmolality contrast agent Niopam appeared to be well tolerated by the plant, whereas Gastrografin showed evidence of toxicity. In summary, the use of iodine-based contrast media allows usually poorly contrasting root structures to be visualized nondestructively using X-ray μCT. In particular, the vascular structures of roots and rhizobial nodules can be clearly visualized in situ.

Three-dimensional (3D) reconstruction of a sample surface from scanning electron microscope (SEM) images taken at two perspectives has been known for decades. Nowadays, there exist several commercially available stereophotogrammetry software packages. For testing these software packages, in this study we used Monte Carlo simulated SEM images of virtual samples. A virtual sample is a model in a computer, and its true dimensions are known exactly, which is impossible for real SEM samples due to measurement uncertainty. The simulated SEM images can be used for algorithm testing, development, and validation. We tested two stereophotogrammetry software packages and compared their reconstructed 3D models with the known geometry of the virtual samples used to create the simulated SEM images. Both packages performed relatively well with simulated SEM images of a sample with a rough surface. However, in a sample containing nearly uniform and therefore low-contrast zones, the height reconstruction error was ≈46%. The present stereophotogrammetry software packages need further improvement before they can be used reliably with SEM images with uniform zones.

In the course of a thorough investigation of the performance-structure-chemistry interdependency at silicon grain boundaries, we successfully developed a method to systematically correlate aberration-corrected scanning transmission electron microscopy and atom probe tomography. The correlative approach is conducted on individual APT and TEM specimens, with the option to perform both investigations on the same specimen in the future. In the present case of a Σ9 grain boundary, joint mapping of the atomistic details of the grain boundary topology, in conjunction with chemical decoration, enables a deeper understanding of the segregation of impurities observed at such grain boundaries.

Statoliths are the only hard structures in the gelatinous bell of most scyphozoan medusae and investigations on these structures could promote investigations of the understudied population dynamics and phylogeny of jellyfish. We examined the statoliths of Aurelia aurita jellyfish of different ages by light microscopic and microtomographic measurements supplemented by scanning electron microscopy. The morphometric analyses confirmed that statolith numbers and sizes increase during jellyfish development and revealed that newly-formed statoliths had similar shapes that may change during statolith growth. Nevertheless, most statoliths had a typical compact rod shape with an aspect ratio of 1–2.5 at all ages and we suggest that the composition of statolith shapes may be taxa specific. We developed a new approach allowing exact measurements of statolith growth for the first time. The application of calcein as a fluorescent marker resulted in clear fluorescent lines within the statoliths, allowing calculations of the statolith side face growth increments (0.1 µm/day; n=252). A single-crystal analysis revealed that the calcein incubation did not affect the statolith crystal structure. In conclusion, calcein labeling is an excellent method to follow the growth of bassanite statoliths.

Electron tomography has become a valuable and widely used tool for studying the three-dimensional nanostructure of materials and biological specimens. However, the incomplete tilt range provided by conventional sample holders limits the fidelity and quantitative interpretability of tomographic images by leaving a “missing wedge” of unknown information in Fourier space. Imaging over a complete range of angles eliminates missing wedge artifacts and dramatically improves tomogram quality. Full-range tomography is usually accomplished using needle-shaped samples milled from bulk material with focused ion beams, but versatile specimen preparation methods for nanoparticles and other fine powders are lacking. In this work, we present a new preparation technique in which powder specimens are supported on carbon nanofibers that extend beyond the end of a tungsten needle. Using this approach, we produced tomograms of platinum fuel cell catalysts and gold-decorated strontium titanate photocatalyst specimens. Without the missing wedge, these tomograms are free from elongation artifacts, supporting straightforward automatic segmentation and quantitative analysis of key materials properties such as void size and connectivity, and surface area and curvature. This approach may be generalized to other samples that can be dispersed in liquids, such as biological structures, creating new opportunities for high-quality electron tomography across disciplines.

Sub-angstrom scanning transmission electron microscopy (STEM) allows quantitative column-by-column analysis of crystalline specimens via annular dark-field images. The intensity of electrons scattered from a particular location in an atomic column depends on the intensity of the electron probe at that location. Electron beam channeling causes oscillations in the STEM probe intensity during specimen propagation, which leads to differences in the beam intensity incident at different depths. Understanding the parameters that control this complex behavior is critical for interpreting experimental STEM results. In this work, theoretical analysis of the STEM probe intensity reveals that intensity oscillations during specimen propagation are regulated by changes in the beam’s angular distribution. Three distinct regimes of channeling behavior are observed: the high-atomic-number (Z) regime, in which atomic scattering leads to significant angular redistribution of the beam; the low-Z regime, in which the probe’s initial angular distribution controls intensity oscillations; and the intermediate-Z regime, in which the behavior is mixed. These contrasting regimes are shown to exist for a wide range of probe parameters. These results provide a new understanding of the occurrence and consequences of channeling phenomena and conditions under which their influence is strengthened or weakened by characteristics of the electron probe and sample.

The refractive index in the interior of single cells affects the evanescent field depth in quantitative studies using total internal reflection (TIR) fluorescence, but often that index is not well known. We here present method to measure and spatially map the absolute index of refraction in a microscopic sample, by imaging a collimated light beam reflected from the substrate/buffer/cell interference at variable angles of incidence. Above the TIR critical angle (which is a strong function of refractive index), the reflection is 100%, but in the immediate sub-critical angle zone, the reflection intensity is a very strong ascending function of incidence angle. By analyzing the angular position of that edge at each location in the field of view, the local refractive index can be estimated. In addition, by analyzing the steepness of the edge, the distance-to-substrate can be determined. We apply the technique to liquid calibration samples, silica beads, cultured Chinese hamster ovary cells, and primary culture chromaffin cells. The optical technique suffers from decremented lateral resolution, scattering, and interference artifacts. However, it still provides reasonable results for both refractive index (~1.38) and for distance-to-substrate (~150 nm) for the cells, as well as a lateral resolution to about 1 µm.

The rapidity with which epithelial cells cover a wound surface helps determine whether scarring or scar-less healing results. As methylene blue is a vital dye that is absorbed by damaged tissue but not undamaged epidermis, it can be used to assess wound closure. We sought to develop a quantitative methylene blue exclusion assay to estimate the timeframe for re-epithelialization in regenerating appendages in zebrafish and axolotls, two classic model systems of regeneration. Following application of methylene blue to the amputation plane and extensive washing, the regenerating tail was imaged in vivo until staining was no longer visible. The percent area of the amputation plane positive for methylene blue, representing the area of the amputation plane not yet re-epithelialized, was measured for each time point. The loss of methylene blue occurred rapidly, within ~2.5 h in larval and juvenile axolotls and <1 h in adult zebrafish, consistent with high rates of re-epithelialization in these models of regeneration. The assay allows simple, rapid estimation of the time course for regenerative re-epithelialization without affecting subsequent regenerative ability. This technique will permit comparison of re-epithelialization across different strains and stages, as well as under the influence of various pharmacological inhibitors that affect regeneration.

Accurate and fast quantitative analysis of living cells from fluorescence microscopy images is useful for evaluating experimental outcomes and cell culture protocols. An algorithm is developed in this work to automatically segment and distinguish apoptotic cells from normal cells. The algorithm involves three steps consisting of two segmentation steps and a classification step. The segmentation steps are: (i) a coarsesegmentation, combining a range filter with a marching square method, is used as a prefiltering step to provide the approximate positions of cells within a two-dimensional matrix used to store cells’ images and the count of the number of cells for a given image; and (ii) a fine segmentation step using the Active Contours Without Edges method is applied to the boundaries of cells identified in the coarse segmentation step. Although this basic two-step approach provides accurate edges when the cells in a given image are sparsely distributed, the occurrence of clusters of cells in high cell density samples requires further processing. Hence, a novel algorithm for clusters is developed to identify the edges of cells within clusters and to approximate their morphological features. Based on the segmentation results, a support vector machine classifier that uses three morphological features: the mean value of pixel intensities in the cellular regions, the variance of pixel intensities in the vicinity of cell boundaries, and the lengths of the boundaries, is developed for distinguishing apoptotic cells from normal cells. The algorithm is shown to be efficient in terms of computational time, quantitative analysis, and differentiation accuracy, as compared with the use of the active contours method without the proposed preliminary coarse segmentation step.

Fluorescent dyes like Rhodamine B (RB) have been used to identify the spatial distribution of adhesive restorative materials in the tooth/restoration interface. Potential effects of the addition of RB to dental adhesives were addressed in the past, but no further information is available on how to determine suitable concentrations of RB in these bonding agents for imaging in the confocal laser scanning microscope. This study provides systematical strategies for adding RB to viscous dental adhesive resins, focusing on the determination of the lowest range of dye concentrations necessary to achieve an acceptable image of the dentin/adhesive interface. It was demonstrated that optimized images of the resin distribution in dentin can be produced with 0.1–0.02 mg/mL of RB in the (tested) adhesives. Our approaches took into account aspects related to the dye concentration, photophysical parameters in different host media, specimen composition and morphology to develop a rational use of the fluorescent agent with the resin-based materials. Information gained from this work can help optimize labeling methods using dispersions of low-molecular-weight dyes in different monomer blend systems.