The Impact Factor data for 2006 is in, and we are pleased to announce that Microscopy and Microanalysis is ranked #2 among microscopy journals by the ISI Web of Science (Thomson Scientific). This ranking is based on the 2006 Impact Factor of 2.11 (an increase from the 2005 Impact Factor of 1.88).

In this article a method for determining errors of the strain values when applying strain mapping techniques has been devised. This methodology starts with the generation of a thickness/defocus series of simulated high-resolution transmission electron microscopy images of InAsxP1−x/InP heterostructures and the application of geometric phase. To obtain optimal defocusing conditions, a comparison of different defocus values is carried out by the calculation of the strain profile standard deviations among different specimen thicknesses. Finally, based on the analogy of real state strain to a step response, a characterization of strain mapping error near an interface is proposed.

The mean-free-paths for inelastic scattering of high-energy electrons (200 keV) for AlAs and GaAs have been determined based on a comparison of thicknesses as measured by electron holography and convergent-beam electron diffraction. The measured values are 77 ± 4 nm and 67 ± 4 nm for AlAs and GaAs, respectively. Using these values, the mean inner potentials of AlAs and GaAs were then determined, from a total of 15 separate experimental measurements, to be 12.1 ± 0.7 V and 14.0 ± 0.6 V, respectively. These latter measurements show good agreement with recent theoretical calculations within experimental error.

We have applied high-angle annular dark-field microscopy to the characterization of the structure of template-grown nanotubes composed of a polymer and a discotic liquid crystalline material. Selective staining of the liquid crystal phase with ruthenium tetroxide was used to develop adequate Z-contrast that allows us to distinguish between the two phases. At appropriate staining conditions, we could clearly visualize, in the annular dark-field mode, a 5–15-nm thin liquid crystalline layer precipitated on the inner surface of the polymer tubes. Cryo-electron diffraction has shown high alignment of the discotic columns within the layer parallel to the tube axis. However, although the polymer/liquid crystal phase separation is almost complete, the wetting behavior of the polymer in relation to the template appears to be sensitively influenced by kinetic factors.

Atom probe tomography provides a chemical analysis of nanostructured materials with outstanding resolution. However, due to the process of field evaporation triggered by nanosecond high voltage pulses, the method is usually limited to conductive materials. As part of recent efforts to overcome this limitation, it is demonstrated that the analysis of thick NiO and WO3 oxide layers is possible by laser pulses of 500 ps duration. A careful analysis of the mass spectra demonstrates that the expected stoichiometries are well reproduced by the measurement. The reconstruction of lattice planes proves that surface diffusion is negligible also in the case of thermal pulses.

Focused ion-beam milling has been applied to prepare needle-shaped atom probe tomography specimens from mechanically alloyed powders without the use of embedding media. The lift-out technique known from transmission electron microscopy specimen preparation was modified to cut micron-sized square cross-sectional blanks out of single powder particles. A sequence of rectangular cuts and annular milling showed the highest efficiency for sharpening the blanks to tips. First atom probe results on a Fe95Cu5 powder mechanically alloyed in a high-energy planetary ball mill for 20 h have been obtained. Concentration profiles taken from this powder sample showed that the Cu distribution is inhomogeneous on a nanoscale and that the mechanical alloying process has not been completed yet. In addition, small clusters of oxygen, stemming from the ball milling process, have been detected. Annular milling with 30 keV Ga ions and beam currents ≥50 pA was found to cause the formation of an amorphous surface layer, whereas no structural changes could be observed for beam currents ≤10 pA.

The derivation of a universal equation to compute the range of emitted X rays is presented for homogeneous bulk materials. This equation is based on two fundamental assumptions: the φ(ρz) curve of X-ray generation is constant and the ratio of the emitted to the generated X-ray range is equal to the ratio of the emitted to the generated X-ray intensity. An excellent agreement is observed with data obtained from Monte Carlo simulations of 200,000 electron trajectories in C, Al, Cu, Ag, Au, and an Fe–B alloy with boron weight fractions equal to 0.01, 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8, 0.9, and 0.99, performed with the electron beam energy varied from 1 to 30 keV in 1-keV steps. When the ratio of the generated X-ray range to the photon mean free path is much smaller than one, the emission X-ray range is equal to the generated X-ray range, but when this ratio is much greater than one, the emission X-ray range is constant and is given by the product of the effective photon mean free path multiplied by the sine of the take-off angle.

In using microscopic imaging techniques, unbiased selection of sampling areas is often critical when judgment has to be used to find regions of interest. A conditional random sampling was designed to survey hematite particles on a mica surface using tapping-mode atomic force microscopy, based on three adapted-systematic-sampling methods designed to exclude subjective bias by limiting the freedom of arbitrarily selecting sampling areas. The results of these surveying methods were compared with the average particle surface density modeled by Poisson distribution. It was found that the conditional random sampling could survey particles effectively and improve the data reliability significantly. Ten population-known images from the same mica sheet were used to evaluate these methods, and an average relative error of 12% (maximum 21%) was obtained using the conditional random method with six sampling areas. It was used to investigate the effects of common organic pollutants, benzene, toluene, ethylbenzene, and xylenes on the transport of soil colloids.

Two issues that often impact the cryo-electron microscopy (cryoEM) specimen preparation process are agglomeration of particles near hole edges in holey carbon films and variations in vitreous ice thickness. In many cases, the source of these issues was identified to be the residues and topography often seen in commercially available films. To study and minimize their impact during specimen preparation, an improved holey carbon film has been developed. Rather than using a consumable template based on soft materials that must be removed prior to grid assembly, a method was developed that uses a hard template and a water-soluble release layer to replicate the template pattern into the carbon films. The advantages of this method are the improved purity and flatness of the carbon films, and these attributes are shown to have a dramatic improvement on the distribution of single particles embedded in vitreous ice suspended across the holes. Improving particle distribution is an enabling factor toward increasing the throughput of data collection for cryoEM.

Increasingly, genetically modified Salmonella are being explored as a novel treatment for cancer because Salmonella preferentially replicate within tumors and destroy cancer cells without causing the septic shock that is typically associated with wild-type S. typhimurium infections. However, the mechanisms by which genetically modified Salmonella strains preferentially invade cancer cells have not yet been addressed in cellular detail. Here we present data that show S. typhimurium strains VNP20009, LT2, and CRC1674 invasion of PC-3M prostate cancer cells. S. typhimurium-infected PC-3M human prostate cancer cells were analyzed with immunofluorescence microscopy and transmission electron microscopy (TEM) at various times after inoculation. We analyzed microfilaments, microtubules, and DNA with fluorescence and immunofluorescence microscopy. 3T3 Phi-Yellow-mitochondria mouse 3T3 cells were used to study the effects of Salmonella infestation on mitochondria distribution in live cells. Our TEM results show gradual destruction of mitochondria within the PC-3M prostate cancer cells with complete loss of cristae at 8 h after inoculation. The fluorescence intensity in YFP-mitochondria-transfected mouse 3T3 cells decreased, which indicates loss of mitochondria structure. Interestingly, the nucleus does not appear affected by Salmonella within 8 h. Our data demonstrate that genetically modified S. typhimurium destroy PC-3M prostate cancer cells, perhaps by preferential destruction of mitochondria.

Adeno-associated virus (AAV) is a defective, nonpathogenic human parvovirus, which coinfects with a helper adenovirus or herpes virus. AAV's unique characteristics have made it an appealing vector system for gene delivery. AAV or recombinant AAV (rAAV) has been widely detected using negative stain transmission electron microscopy (TEM) but little has been detected using atomic force microscopy (AFM). In this article, we used AFM and TEM to observe the recombinant AAV-2 (rAAV-2) virus particles and applied statistical analysis to the AFM and TEM images. The results indicated that the rAAV-2 particle was a slightly elliptic particle close to round when it was detected by TEM (the mean length of major and minor axes of rAAV-2 particles was 24.77 ± 1.78 nm and 21.84 ± 1.57 nm, respectively), whereas when detected by AFM, the rAAV-2 particle was almost round. Even though the dimensions of the rAAV-2 particle exhibited a polymorphous distribution via off-line particle analysis of AFM, most of the rAAV-2 particles had a mean diameter of approximate 22.04 nm, which was similar to the results obtained by TEM. The results above suggested that AFM was important for accurately determining the average dimensions and distributions of virus particles.

Sialoliths from parotid and submaxillar glands have been characterized. Fractured and polished surfaces revealed an intrinsic structural diversity across the calculi sections. In general, the calculi presented highly mineralized amorphous-looking cores surrounded by concentric alternating mineralized and organic layers. The thickness of these layers decreased from the outer regions toward the center of the sialolith, illustrating a sequence of growth stages. Nevertheless, a significant variability could be detected among the specimens. In some cases, the calculi displayed multiple cores and lacked concentric laminated structures. In other instances, the specimens exhibited extensive regions of globular structures. In these cases, the globule diameter decreased across the radius toward the center of the sialoliths, and the globular structures tended to reorganize, forming bright and dark laminated layers surrounding the core. The participation of globular structures in the layer formation process points to morphogenetic mechanisms not previously described.

Fluorochrome marking of the gastropod Concholepas concholepas has shown that the prismatic units of the shell are built by superimposition of isochronic growth layers of about 2 μm. Fluorescent growth marks make it possible to establish the high periodicity of the cyclic biomineralization process at a standard growth rhythm of about 45 layers a day. Sulphated polysaccharides have been identified within the growth layers by using synchrotron radiation, whereas high resolution mapping enables the banding pattern of the mineral phase to be correlated with the layered distribution of polysaccharides. Atomic force microscopy has shown that the layers are made of nanograins densely packed in an organic component.

Following is a list of microscopy-related meetings and courses. The editors would greatly appreciate input to this list via the electronic submission form found in the MSA World-Wide Web page at http://www.msa.microscopy.com. We will gladly add hypertext links to the notice on the web and insert a listing of the meeting in the next issue of the Journal. Send comments and questions to Nestor Zaluzec, [email protected].