Scanning electron microscopy with energy-dispersive spectrometry has been applied to the analysis of various materials at low-incident beam energies, E0≤5 keV, using peak fitting and following the measured standards/matrix corrections protocol embedded in the National Institute of Standards and Technology Desktop Spectrum Analyzer-II analytical software engine. Low beam energy analysis provides improved spatial resolution laterally and in-depth. The lower beam energy restricts the atomic shells that can be ionized, reducing the number of X-ray peak families available to the analyst. At E0=5 keV, all elements of the periodic table except H and He can be measured. As the beam energy is reduced below 5 keV, elements become inaccessible due to lack of excitation of useful characteristic X-ray peaks. The shallow sampling depth of low beam energy microanalysis makes the technique more sensitive to surface compositional modification due to formation of oxides and other reaction layers. Accurate and precise analysis is possible with the use of appropriate standards and by accumulating high count spectra of unknowns and standards (>1 million counts integrated from 0.1 keV to E0).

A long-standing goal of electron microscopy has been the high-resolution characterization of specimens in their native environment. However, electron optics require high vacuum to maintain an unscattered and focused probe, a challenge for specimens requiring atmospheric or liquid environments. Here, we use an electron-transparent window at the base of a scanning electron microscope’s objective lens to separate column vacuum from the specimen, enabling imaging under ambient conditions, without a specimen vacuum chamber. We demonstrate in-air imaging of specimens at nanoscale resolution using backscattered scanning electron microscopy (airSEM) and scanning transmission electron microscopy. We explore resolution and contrast using Monte Carlo simulations and analytical models. We find that nanometer-scale resolution can be obtained at gas path lengths up to 400 μm, although contrast drops with increasing gas path length. As the electron-transparent window scatters considerably more than gas at our operating conditions, we observe that the densities and thicknesses of the electron-transparent window are the dominant limiting factors for image contrast at lower operating voltages. By enabling a variety of detector configurations, the airSEM is applicable to a wide range of environmental experiments including the imaging of hydrated biological specimens and in situ chemical and electrochemical processes.

Dimensional measurements from secondary electron (SE) images were compared with those from backscattered electron (BSE) and low-loss electron (LLE) images. With the commonly used 50% threshold criterion, the lines consistently appeared larger in the SE images. As the images were acquired simultaneously by an instrument with the capability to operate detectors for both signals at the same time, the differences cannot be explained by the assumption that contamination or drift between images affected the SE, BSE, or LLE images differently. Simulations with JMONSEL, an electron microscope simulator, indicate that the nanometer-scale differences observed on this sample can be explained by the different convolution effects of a beam with finite size on signals with different symmetry (the SE signal’s characteristic peak versus the BSE or LLE signal’s characteristic step). This effect is too small to explain the >100 nm discrepancies that were observed in earlier work on different samples. Additional modeling indicates that those discrepancies can be explained by the much larger sidewall angles of the earlier samples, coupled with the different response of SE versus BSE/LLE profiles to such wall angles.

Electron microscopy of biological, polymeric, and other beam-sensitive structures is often hampered by deleterious electron beam interactions. In fact, imaging of such beam-sensitive materials is limited by the allowable radiation dosage rather that capabilities of the microscope itself, which has been compounded by the availability of high brightness electron sources. Reducing dwell times to overcome dose-related artifacts, such as radiolysis and electrostatic charging, is challenging due to the inherently low contrast in imaging of many such materials. These challenges are particularly exacerbated during dynamic time-resolved, fluidic cell imaging, or three-dimensional tomographic reconstruction—all of which undergo additional dosage. Thus, there is a pressing need for the development of techniques to produce high-quality images at ever lower electron doses. In this contribution, we demonstrate direct dose reduction and suppression of beam-induced artifacts through under-sampling pixels, by as much as 80% reduction in dosage, using a commercial scanning electron microscope with an electrostatic beam blanker and a dictionary learning in-painting algorithm. This allows for multiple sparse recoverable images to be acquired at the cost of one fully sampled image. We believe this approach may open new ways to conduct imaging, which otherwise require compromising beam current and/or exposure conditions.

High-resolution (or “cross-correlation”) electron backscatter diffraction analysis (HR-EBSD) utilizes cross-correlation techniques to determine relative orientation and distortion of an experimental electron backscatter diffraction pattern with respect to a reference pattern. The integrity of absolute strain and tetragonality measurements of a standard Si/SiGe material have previously been analyzed using reference patterns produced by kinematical simulation. Although the results were promising, the noise levels were significantly higher for kinematically produced patterns, compared with real patterns taken from the Si region of the sample. This paper applies HR-EBSD techniques to analyze lattice distortion in an Si/SiGe sample, using recently developed dynamically simulated patterns. The results are compared with those from experimental and kinematically simulated patterns. Dynamical patterns provide significantly more precision than kinematical patterns. Dynamical patterns also provide better estimates of tetragonality at low levels of distortion relative to the reference pattern; kinematical patterns can perform better at large values of relative tetragonality due to the ability to rapidly generate patterns relating to a distorted lattice. A library of dynamically generated patterns with different lattice parameters might be used to achieve a similar advantage. The convergence of the cross-correlation approach is also assessed for the different reference pattern types.

We demonstrate that the second-Stokes output from a diamond Raman laser, pumped by a femtosecond Ti:Sapphire laser, can be used to efficiently excite red-emitting dyes by two-photon excitation at 1,080 nm and beyond. We image HeLa cells expressing red fluorescent protein, as well as dyes such as Texas Red and Mitotracker Red. We demonstrate the potential for simultaneous two-color, two-photon imaging with this laser by using the residual pump beam for excitation of a green-emitting dye. We demonstrate this for the combination of Alexa Fluor 488 and Alexa Fluor 568. Because the Raman laser extends the wavelength range of the Ti:Sapphire laser, resulting in a laser system tunable to 680–1,200 nm, it can be used for two-photon excitation of a large variety and combination of dyes.

Three-dimensional (3D) nondestructive microstructural characterization was performed using full-field transmission X-ray microscopy on an Sn-rich alloy, at a spatial resolution of 60 nm. This study highlights the use of synchrotron radiation along with Fresnel zone plate optics to perform absorption contrast tomography for analyzing nanoscale features of fine second phase particles distributed in the tin matrix, which are representative of the bulk microstructure. The 3D reconstruction was also used to quantify microstructural details of the analyzed volume.

High-pressure die-casting (HPDC) AM50 tensile specimens were used to investigate characteristics of gas pores and its effect on mechanical properties of HPDC AM50 magnesium alloy. Combining microstructure morphology gained from optical microscopy, scanning electron microscopy (SEM), and three-dimensional (3D) reconstruction with the experimental data from uniaxial tensile testing, we pursued the relationship between gas pores and the mechanical properties of HPDC AM50 Mg alloy. Results indicate that comparing with 3D reconstruction models, 2D images like optical metallography images and SEM images have one-sidedness. Furthermore, the size and maximum areal fraction of gas pores have negative effects on the mechanical properties of HPDC AM50 Mg alloy. With increase of the maximum size of gas pores in the specimen, the ultimate tensile strength (UTS) and elongation decrease. In addition, with the maximum areal fraction becoming larger, both the UTS and elongation decrease linearly.

In this paper, the change detection of a fast turning specimen is studied at micro-level, whereas the images are acquired without stopping the rotation. In the beginning of the experiment, the imaging system is focused on the surface of the specimen. By starting the rotation of the specimen, the diameter of the specimen changes due to wear, which results in de-focusing of the imaging system. So the amount of blur in the images can be used as evidence of the wear phenomenon. Due to the properties of the microscope, the corners of the frames were dark and had to be cropped. So, each micrograph reflects only a small area of the surface. Nevertheless, techniques like stitching of multiple images can provide a significant surface area for micro-level investigation which increases the effectiveness of analyzing the material modification. Based on the results computer vision could detect a change of about 1.2 µm in the diameter of the specimen. More important is that we could follow the same locations of the surface in the microscopic images despite blurring, uneven illumination, change on the surface, and relatively a high-speed rotation.

Carbon fibers exhibit exceptional properties such as high stiffness and specific strength, making them excellent reinforcements for composite materials. However, it is difficult to directly measure their tensile properties and estimates are often obtained by tensioning fiber bundles or composites. While these macro scale tests are informative for composite design, their results differ from that of direct testing of individual fibers. Furthermore, carbon filament strength also depends on other variables, including the test length, actual fiber diameter, and material flaw distribution. Single fiber tensile testing was performed on high-strength carbon fibers to determine the load and strain at failure. Scanning electron microscopy was also conducted to evaluate the fiber surface morphology and precisely measure each fiber’s diameter. Fiber strength was found to depend on the test gage length and in an effort to better understand the overall expected performance of these fibers at various lengths, statistical weak link scaling was performed. In addition, the true Young’s modulus was also determined by taking the system compliance into account. It was found that all properties (tensile strength, strain to failure, and Young’s modulus) matched very well with the manufacturers’ reported values at 20 mm gage lengths, but deviated significantly at other lengths.

In this study, an integrated analytical method was developed to investigate the composition of both the inorganic pigments and organic binders of polychrome relics in Maiji Mountain Grottoes in northwestern China. Cross-sections of each sample were prepared at the beginning of the study, and all experiments were carried out on these cross-sections. Polychromic structures were revealed by optical microscopy and scanning electron microscopy-backscattered electron imaging. Inorganic materials were determined by using SEM coupled with an energy dispersive spectrometer and μ-Raman spectrometer, whereas organic materials were identified by staining techniques and highly sensitive and specific immunofluorescence microscopy. Data showed that the red colors are attributed to one or two pigments of red ochre, cinnabar, and minium; the blue pigment is natural lazurite; the green pigment is ascribed to atacamite; the white color is attributed to potassium feldspar; and the black surface is formed by the discoloration of minium to plattnerite under the influence of environmental factors. Regarding organic binders used in painting and preparation layers, mammalian animal glue and chicken egg white were both found alone or in mixture. Finally, the conclusion is made that the Secco technique is employed in polychrome relics from Maiji Mountain Grottoes.

Photographic prints of platinum metal on paper supports are some of the most exquisite and expressive in the world of fine art photography. Platinum prints were produced from about 1890 to 1920 in the USA and Europe. The chemical and material nature of these valuable prints is of great interest to many who are interested in their long-term preservation, in the intersection of science and art, and in the scientific and technical study of cultural heritage. This paper presents the results of a characterization study using newer electron microscopy techniques. In this study, a low vacuum high-resolution scanning electron microscope was used to study the surface and sub-surface of historic and modern platinum and/or palladium print samples. Using environmental SEM pressures allowed us to investigate the actual top surface and sub-surface with cross-sections without any preparation; no coatings of carbon or other material. Cross-sections were prepared using an argon plasma cross-polishing system. This study shows that the photographic image of platinum prints is composed of platinum nanoparticles embedded in the upper layers of the paper’s cellulosic fibers.

The acquisition of neuroendocrine (NE) characteristics by prostate cancer (PC) cells relates to tumor progression and hormone resistance. PC cells may survive and function in androgen-deprived environments, where they could establish paracrine signaling networks, providing stimuli for the propagation of local carcinoma cells. We previously demonstrated, using electron probe X-ray microanalysis (EPXMA), in LNCaP, PC-3, and Du 145 cell lines that apoptosis is associated with intracellular elemental changes, and that the NE secretory products, bombesin and calcitonin, inhibit etoposide-induced apoptosis, as well as some of these elemental changes. In this study, LNCaP cells were induced in vitro to transdifferentiate under androgen deprivation, to mimic the role of NE cells in the apoptotic activity of transdifferentiated androgen-dependent PC cells. Changes in intracellular ion content associated with apoptosis, assessed by EPXMA, demonstrate that the transdifferentiated LNCaP cells are resistant to etoposide-induced apoptosis and also to the etoposide-induced elemental changes. The aggressive malignant potential of PC with neuroendocrine differentiation, associated with hormonal independence, is partly because of the ability that most NE tumor cells have to escape apoptosis, which can enhance the malignant properties of tumor cells and may have therapeutic implications as tumor cells are usually resistant to cytotoxic drugs as etoposide.

Combined oral contraceptives (COCs), colloquially referred to as “the pill,” have been regarded as a medical breakthrough, as they have improved the lives of countless women, from simplifying family planning to the treatment of acne, endometriosis, polycystic ovarian syndrome, and dysmenorrhea. Unfortunately, COC usage has been associated with an increased occurrence of venous thrombosis and therefore a systemic hypercoagulable state in susceptible females. Here we discuss the health risks of COC usage and use viscoelastic and morphological techniques to investigate the effect of different COC constituents on clot formation, particularly fibrin network packaging and whole blood viscoelasticity. Viscoelastic properties of whole blood showed gender-specific changes while morphological alterations were person-specific, regardless of gender. Using scanning electron microscopy and thromboelastography provides great insight regarding fibrin packaging and the development of a hypercoagulable state in high-risk individuals. We proposed a three-step approach where (1) an individual’s coagulation profile baseline is determined, after which (2) the “ideal” combination of constituents is prescribed, and (3) the coagulation profile of the individual is monitored to assess possible risk of thrombosis. Only in following such an individualized patient-oriented approach will we be able to avoid the many health issues due to COC usage in susceptible females.

The objective of this work was to obtain Spirulina (Arthrospira maxima) nanoparticles (SNPs) by using high-impact mechanical milling and to characterize them by electron microscopy and spectroscopy techniques. The milling products were analyzed after various processing times (1–4 h), and particle size distribution and number mean size (NMS) were determined by analysis of high-resolution scanning electron microscopic images. The smallest particles are synthesized after 3 h of milling, had an NMS of 55.6±3.6 nm, with 95% of the particles being smaller than 100 nm. High-resolution transmission electron microscopy showed lattice spacing of ~0.27±0.015 nm for SNPs. The corresponding chemical composition was obtained by energy-dispersive X-ray spectroscopy, and showed the presence of Ca, Fe, K, Mg, Na, and Zn. The powder flow properties showed that the powder density was higher when the average nanoparticle size is smaller. They showed free flowability and an increase in their specific surface area (6.89±0.23 m2/g) up to 12–14 times larger than the original material (0.45±0.02 m2/g). Fourier transform infrared spectroscopy suggested that chemical damage related to the milling is not significant.

ORAI1 proteins are ion channel subunits and the essential pore-forming units of the calcium release-activated calcium channel complex essential for T-cell activation and many other cellular processes. In this study, we used environmental scanning electron microscopy (ESEM) with scanning transmission electron microscopy (STEM) detection to image plasma membrane expressed ORAI1 proteins in whole Jurkat T cells in the liquid state. Utilizing a stably transfected Jurkat T cell clone expressing human ORAI1 with an extracellular human influenza hemagglutinin (HA) tag we investigated if liquid-phase STEM can be applied to detect recombinant surface expressed protein. Streptavidin coated quantum dots were coupled in a one-to-one stoichiometry to ORAI1 proteins detected by biotinylated anti-HA fragmented antibody fragments. High-resolution electron microscopic images revealed the individual label locations from which protein pair distances were determined. These data were analyzed using the pair correlation function and, in addition, an analysis of cluster size and frequency was performed. ORAI1 was found to be present in hexamers in a small fraction only, and ORAI1 resided mostly in monomers and dimers.

Sensory structures (sensilla) of insects are present in high number in the antennae are important for perceiving environmental cues. Thus, sensilla play an important role in the localization, discrimination, and acceptance of a possible host by parasitoid insects. The sensilla, classified according to their shape, size, and distribution, may also show sexual dimorphism in insects. The types and distribution of antennal sensilla in female and male parasitoid Trichospilus pupivorus (Ferriere, 1930) (Hymenoptera: Eulophidae) were evaluated. T. pupivorus females had longer antennae than males. Both males and females have ten sensilla types with higher abundance of placoid sensilla in females, which suggest a possible functional dimorphism.

We report ultrastructural features and transmission electron tomography of the dhub lizard (Uromastyx aegyptia) cornea and its adaptation to hot and dry environments. Six corneas of dhub lizards were fixed in 2.5% glutaraldehyde and processed for electron microscopy and tomography. The ultrathin sections were observed with a JEOL 1400 transmission electron microscope. The cornea of the dhub lizard is very thin (~28–30 µm). The epithelium constitutes ~14% of the cornea, whereas the stroma constitutes 80% of the cornea. The middle stromal lamellae are significantly thicker than anterior and posterior stromal lamellae. Collagen fibril (CF) diameters in the anterior stroma are variable in size (25–75 nm). Proteoglycans (PGs) are very large in the middle and posterior stroma, whereas they are small in the anterior stroma. Three-dimensional electron tomography was carried out to understand the structure and arrangement of the PG and CFs. The presence of large PGs in the posterior and middle stroma might help the animal retain a large amount of water to protect it from dryness. The dhub corneal structure is equipped to adapt to the dry and hot desert environment.