Compared with traditional GPS signals, modern GNSS signals are much more complex and have various new modulations. This introduces a difficulty in combining multiple signal components into a constant-envelope signal that maximises the power efficiency of High Power Amplifiers (HPA) on satellites. This paper first describes the fundamental Phase-Optimised Constant-Envelope Transmission (POCET) technique that searches the optimum combining solution for multiple binary navigation signals. Then the Compass B1/B3 signals are modelled by POCET. For the B1 band, a binary complex sub-carrier is adopted to implement the centre frequency difference between regional and global Compass navigation systems. Regional B1 Open Service (OS) signals and global TMBOC signals are combined with optimum loss of 1·0 dB. For the B3 band, Interplex modulation is proved to be the optimum method to combine QPSK (10) and BOC (15, 2·5) signals. Signal quality in the presence of finite word-length effects of Digital-Analog (DA) converters is analysed. Simulations for signal model validation are conducted. The result indicates that relative amplitude error less than 0·01 and angle error less than 0·1 degree can be achieved with 10 bit DA converters. The POCET method is demonstrated as an efficient solution for Compass signals.

In the maritime community, a runner-up will undertake this typical process to catch up with the front runner; first, as a nation's economy grows its domestic crew costs rise, creating a gap with those abroad, which in turn depresses the international competitiveness of shipping companies. Then, to maintain their economic strength, shipping companies have their ships fly a “flag of convenience” relying on increasing amounts of cheap foreign labour. As a result, the nation gradually loses domestic seafarers, which, in the worst case, leads to a depletion of national human resource needed for its maritime cluster to continue to exist. In that sense, the personnel shortage issue is a fate for top runners in the marine transport world, where international competitiveness is inevitable. The Japanese maritime sector is just facing this issue. In this paper, the current situation in the maritime sector and its dependence on foreign labour, the cause and process of the change and the problems of the outcomes are explained, and the possible solutions in terms of the social mechanism of personnel development and utilization are discussed.

Some new Advanced Driver Assistance Systems (ADAS) need on-the-lane vehicle positioning on accurate digital maps, but current applications of vehicle positioning do not justify the surcharge of very accurate equipment such as DGPS or high-cost inertial systems. For this reason, the performance of GPS in autonomous mode is analyzed. Although satisfactory results can be found, in some areas the GPS signal is lost or degraded so it is necessary to know the positioning error when using only inertial system data. A theoretical approach based on the uncertainty propagation law is used to estimate the upper limit of distance that can be travelled fulfilling the specifications of an assistance system. Test results support the conclusions of this approach. Finally, the combination of GPS and inertial systems is studied, with the conclusion that the theoretical approach is valid when inertial measurements are used right from the start of GPS signal degradation, without waiting for a complete loss of signal.

Current strategic plans for air traffic management (ATM) envisage a transition from radar control to a trajectory-based system. The future ATM concepts are very different in a great number of aspects from the present system. The focus here is on the design of safe systems, in particular the appropriate air traffic control (ATC) separation minima. This Part 1 sketches the historical origins of ATC separation minima and then analyses the safety thinking behind current minima and the issues involved in risk modelling. Why have the critical minima largely remained unchanged for several decades – stasis? Part 2 then addresses key safety issues in the transition to the new ATM concept.

‘Give me a lever long enough and a fulcrum on which to place it, and I shall move the world.’ Archimedes.

International standards require the use of a weighted least-squares approach to onboard Receiver Autonomous Integrity Monitoring (RAIM). However, the protection levels developed to determine if the conditions exist to perform a measurement check (i.e. failure detection) are not specified. Various methods for the computation of protection levels exist. However, they are essentially approximations to the complex problem of computing the worst-case missed detection probability under a weighted system. In this paper, a novel approach to determine this probability at the worst-case measurement bias is presented. The missed detection probabilities are then iteratively solved against the integrity risk requirement in order to derive an optimal protection level for the operation. It is shown that the new method improves availability by more than 30% compared to the baseline weighted RAIM algorithm.

A version of this paper was first presented at the US Institute of Navigation (ION) GNSS 2009 Conference in Savannah, Georgia.

Carrier phase measurements are used to provide high-accuracy estimates of position. For safety-of-life navigation applications such as precision approach and landing, integrity plays a critical role. Carrier phase-based Receiver Autonomous Integrity Monitoring (CRAIM) has been investigated for many years (Pervan et al, 1998; Feng et al, 2007). Assuming that the carrier phase error has a Gaussian distribution, conventional CRAIM algorithms were directly derived from the Pseudorange-based RAIM (PRAIM). However, the actual carrier phase error does not exactly follow the Gaussian distribution, hence the performance of the conventional CRAIM algorithm is not optimal.

To approach this problem, this paper proposes a new CRAIM algorithm that uses Gaussian sum filters. A Gaussian sum filter can deal with any non-Gaussian error distribution and accurately present the posterior distributions of states. In this paper, a new method of making a Gaussian mixture model, which follows the true error distribution, is introduced. Additionally an integrity monitoring algorithm, using a Gaussian sum filter, is described in detail. The simulation results show that the proposed algorithm can have about 18% smaller Minimum Detectable Bias (MDB) and generates about 20% lower protection levels than those of the conventional CRAIM algorithm. In other words, by considering a non-Gaussian carrier phase error distribution, the new algorithm can improve the accuracy and the availability.

A dynamic state realization for tightly coupling Global Positioning System (GPS) measurements with an Inertial Navigation System (INS) is described. The realization, based on the direct fusion of GPS and INS systems through Kalman filter state dynamics, explicitly accounts for temporal and spatial decorrelation of GPS measurement errors (such as tropospheric, ionospheric, and multipath errors) through state augmentation, thereby ensuring Kalman filter integrity under fault-free error conditions. Predicted system performance for a Local Area Augmentation System (LAAS) aircraft precision approach application is evaluated using covariance analysis and validated with flight data.

Built-in fault detection mechanisms based on the Kalman filter innovations are also evaluated to help provide integrity under certain fault conditions. It is shown that an algorithm based on the integral of Kalman filter innovations outperforms other existing GPS fault detection methods in the detection of slowly developing ranging errors, such as those caused by ionospheric and tropospheric anomalies.

In low-cost self-contained pedestrian navigation systems, traditional Pedestrian Dead Reckoning (PDR) solutions utilize accelerometers to derive the speed as well as the distance travelled, and obtain the walking heading from magnetic compasses or gyros. However, these measurements are sensitive to instrument errors and disturbances from ambient environment. To be totally different from these signals in nature, the electromyography (EMG) signal is a typical kind of biomedical signal that measures electrical potentials generated by muscle contractions from the human body. This kind of signal would reflect muscle activities during human locomotion, so that it can not only be used for speed estimation, but also disclose the azimuth information from the contractions of lumbar muscles when changing the direction of walking. Therefore, investigating how to utilize the EMG signal for PDR is interesting and promising. In this paper, a novel EMG-based speed estimation method is presented, including setup of the EMG equipment, pre-processing procedure, stride detection and stride length estimation. Furthermore, this method suggested is compared with the traditional one based on accelerometers by means of several field tests. The results demonstrate that the EMG-based method is effective and its performance in PDR can be comparable to that of the accelerometer-based method.

Navigational collisions are one of the major safety concerns for many seaports. Despite the extent of work recently done on collision risk analysis in port waters, little is known about the influential factors of the risk. This paper develops a technique for modelling collision risks in port waterways in order to examine the associations between the risks and the geometric, traffic, and regulatory control characteristics of waterways. A binomial logistic model, which accounts for the correlations in the risks of a particular fairway at different time periods, is derived from traffic conflicts and calibrated for the Singapore port fairways. Results show that the fairways attached to shoreline, traffic intersection and international fairway attribute higher risks, whereas those attached to confined water and local fairway possess lower risks. Higher risks are also found in the fairways featuring higher degree of bend, lower depth of water, higher numbers of cardinal and isolated danger marks, higher density of moving ships and lower operating speed. The risks are also found to be higher at night.

As the technology of global navigation satellite system (GNSS) and augmentation systems are evolving rapidly, compatibility becomes a critical issue for system providers. By April 2011, China had successfully launched eight satellites of the Compass phase II (CP II) navigation system, which will provide positioning, navigation, timing and communication services to the Asia-Pacific region by the year 2012. Due to the limitations of available radio frequency bandwidths, it is important to assess the compatibility and to design signals based on the compatibility within these limited radio frequency bandwidths. This paper presents a modified compatibility assessment methodology, derived from the traditional methodologies that are based on the spectral separation coefficient (SSC) and the effective carrier-power-to-noise density ratio. The modified methodology takes into account additional factors including the Doppler offset, code tracking loop, and band-limiting, sampling and quantisation (BSQ) of the GNSS receiver. In the simulation section, the comprehensive compatibility assessment between CP II and other GNSSs, such as GPS, Galileo, Wide Area Augmentation System (WAAS) and European Geostationary Navigation Overlay Service (EGNOS) on L1 Band are carried out and presented with some new results. Simulation results reveal that CP II does not cause serious interference on GPS, Galileo, WAAS and EGNOS as the interference level is below the 0·25 dB threshold recommended by ITU.

In this paper an adaptive unscented Kalman filter based mixing filter is used to develop a high-precision kinematic satellite aided inertial navigation system with a modern receiver that incorporates carrier phase smoothing and ambiguity resolution. Using carrier phase measurements with multiple antennas, in addition to a set of typical pseudo-range estimates that can be obtained from a satellite navigation system such as GPS or GLONASS, the feasibility of generating high precision estimates of the typical outputs from an inertial navigation system is demonstrated. The methodology may be developed as a stand-alone system or employed in conjunction with a traditional strapped down inertial navigation system for purposes of initial alignment. Moreover the feasibility of employing adaptive mixing facilitates the possibility of using the system in an interoperable fashion with satellite navigation measurements.

Unlike a direct broadcasting satellite navigation system, the transmitting satellite navigation system developed in China uses transponders onboard communication satellites to retransmit navigation signals generated at a ground master station. The transmitting navigation satellite constellation consists of a number of inclined geosynchronous orbit (IGSO) satellites. Considering China's mainland coverage in the northern hemisphere occupies some 62 degrees in longitude, the inclination of the IGSO satellites cannot be too high, or its signals would not be received by the users in the middle and high latitude areas when the IGSO satellite travels over the southern hemisphere. Meanwhile, the latitude of the most southerly station in China mainland that can uplink navigation signals is about 18°N when the IGSO satellite travels to the southern hemisphere. Therefore, there is a need to consider the IGSO inclination to achieve balance between uplinking high-quality navigation signals and covering the high-latitude area. In this work, the navigation performance and availability of the IGSO satellite are examined when navigation signals are uplinked from the stations Lintong and Sanya.

In our paper The Risk Homeostasis Theory1, it was accepted that the behaviour of people involved in the operation of cargo carrying ships is conditioned to maximize the economic benefits of the amount of risk assumed in the transport. As a follow-up to that paper, the objective of this one is to investigate the relationship between the level of compliance of the cargo carrying vessels with international standards and the degree of severity of the incidents they are involved in. For this purpose, we analyse the same sample of 2,584 cargo carrying ships involved in incidents during 2005 and 2006 used in that investigation. The variables of the Paris MoU to identify substandard ships are used again to measure the standard level of ships and the degree of seriousness of incidents is determined by the number of days ships are under repair.

The benefits of Global Navigation Satellite Systems (GNSS) and in particular GPS have been demonstrated worldwide, and continue to accrue in the form of new applications. Today, some mission critical applications (largely driven by safety) mostly in aviation and to a lesser extent maritime, rely on a number of techniques for the provision of integrity monitoring services. However, for many applications such as those associated with the emergency services, road user charging and personal navigation devices, no such monitoring exists and service validation is limited due to technical and cost constraints. The problem is exacerbated by a recent increase in more challenging problems, particularly in the security industry, in which jamming devices have been used to disrupt the use of GPS. This paper presents a new approach for a cost effective local solution to the problems above, at the individual user level, by providing the user with information on Quality of Service (QoS). The approach is based on the deployment of a single or network of probes supported by an existing regional network. The probes communicate with a central server and are designed to detect localised events whilst the regional network isolates space segment anomalies. The latter is addressed in detail in this paper in terms of design methodology and performance, using the Ordnance Survey's UK GNSS network.

The CNS/ATM concept envisages reliance on global satellite navigation systems to underpin future air traffic management that is able to cope with the ever-increasing demand for air travel without jeopardising safety and the environment. In order to benefit from GNSS, it is crucial that the navigation performance required of air navigation systems is derived and agreed, based on sound principles. Significant work has been undertaken to date and agreement reached on the navigation requirements for the phases of flight up to Category I (CAT-I) precision approach, and proposals are under discussion for CAT-III precision approach. This paper completes a typical flight profile by addressing airport surface movement, and proposing the requirements based on operational requirements for each airport category, to support operations in zero visibility conditions. The benefits of the approach taken in the derivation of the requirements are discussed relative to the existing navigation requirements.

In designing and developing navigation receiver embedded software, the correct scheduling of navigation tasks is critical for ensuring that a receiver works in the right way. If a receiver's timing scheduling becomes abnormal, it may lead to timing conflicts of the multi-tasking navigation receiver, which may seriously influence the system's performance of real-time features and functionalities. This paper models the timing scheduling of navigation receivers by extracting all important timing parameters including the execution time, period, deadline and priority etc., and focusing on the execution time. The maximum execution time of a navigation task relies on the design and implementation algorithms and the computing capability of the processor. The execution time parameter can be properly adjusted in receiver software design or even in the phase of the receiver requirement changes. On the other hand, the other parameters (i.e., the period, deadline and priority) mainly depend on the receiver's technical requirements, and usually these parameters are set to constant values. In this research, a novel off-line method based on the maximum allowed execution time dichotomy optimization is proposed, and the equilibrium rule is proposed to apply to the multi-task maximum allowed execution time dichotomy search and an analysis of time series of those parameters obtained from real observations of receiver tasks was also conducted. Results indicate that the relative equilibrium is more suitable to the multi-task scheduling of receiver navigation, compared to the absolute equilibrium. The proposed method provides a fast off-line scheduling approach for the top level task design of navigation receivers, and remarkably improves the development efficiency of receiver embedded software.

Integrating the visual navigation mechanism of flying insects with a nonlinear Kalman filter, this paper proposes a novel navigation algorithm. New concepts of entropic map and entropy flow are presented, which can characterize topographic features and measure changes of the image respectively. Meanwhile, an auto-selecting algorithm of assessment threshold is proposed to improve computational accuracy and efficiency of global motion estimation. The simulation results suggest that the navigation algorithm can perform real-time rectification of the missile's trajectory well, and can reduce the cost of the missile's hardware.

Human watch-keeping is necessary to prevent incidents at sea such as groundings and collisions. For many years, electronic aids to navigation have been utilised in watch-keeping but, with electronic marine systems becoming more sophisticated, the part they play in preventing collisions and groundings should become increasingly important. However, this article uses secondary data from the Safety Digest for 2008 compiled by the Marine Accident Investigation Bureau of the United Kingdom; eight case studies are used to show that electronic marine systems, whether integrated or not, are still playing a part in poor watch-keeping resulting in collisions, near misses and groundings. Primary data from fishing skippers of British based vessels have been used to confirm the findings from the secondary data that poor watch-keeping is often the cause of not keeping a proper lookout and that the watch-keeper has a too heavy reliance on the electronic aids. Brief suggestions are made as to how the electronic aids may be adapted to overcome these problems and thus to support the watch-keeper.

Current strategic plans for Air Traffic Management (ATM) envisage a transition from radar control to a trajectory-based system. Part 1 sketched the historical origins of separation minima and then analysed the safety thinking behind current minima and the issues involved in risk modelling. Part 2 examines the future situation. This focuses on the intermediate steps to the final system – upgraded capabilities in a mixed-equipage system. Future traffic mixes two categories of traffic: V aircraft, i.e. vectored traditional ATC-handled, and 4D aircraft, i.e. flying on 4D trajectories. Conflict probe and other decision support tools will need to be in place, inter alia to prevent controller workload from increasing. Conceptually, future risks in the transition period will be the sum of three types of aircraft encounter risk: V/V, 4D/4D and 4D/V. These pose different kinds of problem for ATC, appropriate conflict alerting systems and risk assessment. The numbers of 4D/V encounters increase rapidly with growth in the proportion of 4D aircraft. With reduced minima, airborne collision avoidance systems would be unlikely to resolve higher relative velocity encounters were the ATC system to fail. It would be a difficult decision to reduce markedly ATC separation minima for any category of aircraft encounters during the transition period.

In this study, satellite based pseudo-range measurements are integrated with accelerometer measurements made by six accelerometers located on the six faces of a cuboid, to independently measure the translational and rotational accelerations, and the pseudo-range. These measurements are then processed by an adaptive Unscented Kalman filter (UKF) to correct for the estimated errors and to obtain the required position and velocities at two independent locations. The relative position and velocity are then obtained by the application of standard vector identities. From these estimates, the position and velocity kinematics of prosthetic limbs and measurements of the joint angles, the true ambulatory position is estimated using a third independent UKF based estimator. The robotic limb joint offsets are assumed to be biased which are also estimated by the third UKF. The basic assumption is that the errors in the measurements are quite similar at the two locations and for this reason it is hypothesised that these errors would be reduced when the relative position and velocity were estimated. The results indicate that the steady-state ambulatory position error of the end-effector is reduced by more than 98%.