This work introduces a method for plasma state supervision, based on a frequency-modulated continuous wave radar sensor and a suitable signal evaluation enabling a continuous supervision method for the plasma state. Highly precise phase evaluation of the signal allows us to detect and visualize smallest changes in the plasma state. Assuming the plasma to act like a frequency-dependent dielectric material, the propagation of the electromagnetic wave depends on the plasma state and hence, also the measured phase. Broadband measurements are carried out at center frequencies of 80 and 140 GHz in a low-pressure plasma. The radar-based setup can be used for a very flexible application, capable for spatially resolved measurements in the plasma bulk. At the same time, the high measurement rate allows for quasi real-time monitoring, so that transient processes in the plasma are recorded. Due to the simple setup, this approach is most suitable for industrial applications to improve process control. The chosen different frequencies will show a change in the influence of the plasma on the electromagnetic wave demonstrating the advantages of multi-frequency approaches in future applications.

Short-channel Gallium Nitride (GaN) high-electron-mobility transistors (HEMTs) often utilize T-shape gates due to their large gate-line cross-sectional area and subsequent fMAX increase. In this paper, we report the linearity trade-offs associated with varying the T-gate geometries of AlGaN/GaN HEMTs on Si, specifically the gate extensions which serve as field plates and their impact on the large-signal performance. Small-signal characterization and modeling, in addition to TCAD, provide initial guidelines for the optimal dimensions for the gate field plates using the ratio of fT and the product of the gate resistance and the gate-to-drain capacitance. We utilize various characterization methods, including 6 GHz non-linear vector network analyzer characterization in addition to load-pull, to quantify the amplitude and phase distortion and their subsequent impact on the large-signal metrics of the devices under differing matching conditions and bias points. We deduce that the influence of the gate field plates on the amplitude and phase distortion is non-negligible, particularly under matched conditions.

A dual-band dual-linearly polarized waveguide slot array antenna is proposed in this paper. Two orthogonal slots share a short-circuit wall on broad side. The horizontal and vertical slots, which actualize dual-frequency bands and dual-linear polarization, generate vertically polarized electric fields in 9.39–9.78 GHz and horizontally polarized electric fields in 11.62–12.3 GHz, respectively. The equivalent permittivity of the waveguide is changed by two grooves at the bottom of the waveguide, which improves phase velocity. Two grooves can also reduce the distance between the elements while suppressing the side lobes. Compared to filling the medium in the waveguide, two grooves have less losses. Moreover, the antenna is simple with one input port. The array antenna also overcomes the problems of beam scanning compared with the traditional waveguide slot array antenna. A 1 × 8 antenna array is fabricated and measured to verify the design. The horizontal polarization is formed in 9.39–9.78 GHz, the vertical polarization is generated in 11.62–12.3 GHz, and the antenna gain can reach 15 dBi.

Radio telescopes are among the applications with the highest demands on a local oscillator (LO), which is used to receive and process the signals coming from the sky. Therefore the modules providing the required LO signal have traditionally been big and complicated. To overcome this disadvantage, we implement our own integrated frequency synthesizer inside a small LO module in this article. With this synthesizer we are able to achieve a jitter of only 50 fs integrated from 10 Hz to 2.5 GHz offset at a carrier frequency of 75 GHz. This is in part achieved by a very low in-band phase noise of −111.8 dBc at 10 kHz offset. The stabilizable frequency range is 62–88 GHz. Thus achieving promising results to fulfill this very demanding task with integrated frequency synthesizers in the future.

A 5G rotated frame radiator for multiple applications is presented in the following paper. The presented geometry is capable of radiating the large frequency band from 2.91 to 12.17 GHz, which covers the 5G-(I) sub-6 GHz band, X-band communication with high efficiency. The impedance bandwidth of the radiator is 128%, with an electrical size of 0.24 λ × 0.24 λ × 0.15 λ in lambda. The antenna is simulated with an FR4 substrate using CST Simulator. 06-stages evolution process is also investigated by simulations, and corresponding S-parameter results are presented. Antenna's design comprises a patch in a rotated square fractal-like frame fed by a microstrip line. The proposed structure also demonstrates stable radiation patterns across the operating bandwidth. The proposed radiator has a high gain of 3.8 dBi, and an efficiency of 85%, which claimed that UWB range of the designed antenna. Therefore, it is useful for 5G-(I) sub-6 GHz band, X-band applications, including mobile, radar, and satellite microwave communication.

With increasing demands on resolution and flexibility in current and future radar applications, the focus is moving to digital radar systems such as orthogonal frequency-division multiplexing (OFDM) radars. To achieve high bandwidths and consequently a high range resolution, high sampling rates are needed. To overcome this constraint, an approach called frequency comb OFDM radar has been developed. This paper presents a novel, hardware efficient implementation of such a frequency comb OFDM radar including a novel way of comb generation. Special attention is put on the suppression of unwanted frequency components. Measurements which demonstrate the functionality of the hardware efficient radar system in combination with the frequency comb OFDM technique are presented.

Wireless-connected wearable electronics are finding extensive usage for diagnostic and therapeutic purposes after the globally spread pandemic disease of COVID-19. Although they are undoubtedly helpful for keeping physical distance, their health effects are still under investigation from different aspects and are still a concern for the end-users. In this study, a custom M-shaped wearable antenna covering the wireless body area network and wireless local area network frequencies is designed, built, and measured. A beret cap made from a 2 mm thick textile is used as a substrate. The specific absorption rate (SAR) in a realistic human-head model due to electromagnetic energy produced by the antenna is evaluated using the finite-difference time-domain method. The SAR distributions for 1-g and 10-g tissues are calculated at 2.4 and 5.8 GHz. It is shown that the obtained maximum SAR values for 1-g and 10-g tissues at each frequency of interest were less than the limits determined by IEEE RF exposure guidelines and standards.

Terahertz technologies for non-destructive testing (NDT) are continuing to find their way into the industrial sector in the context of very specific inspection tasks. Part of this development is the capability to adapt terahertz systems in such a way that they can meet the sometimes harsh challenges and requirements of real-world industrial scenarios. One such scenario is the inspection of components with limited available measurement space. In particular, we show here the terahertz NDT inspection of the mica insulation of generator bars of turbogenerators at power plants, where an early on-site detection of defects and cracks in the insulation can be crucial, but where only few centimeters of space between adjacent bars are available. To address this problem, we have developed a measurement system combining a 100 GHz all-electronic terahertz transceiver with a low-loss dielectric waveguide antenna with 90 degree tip. We achieve sub-wavelength image resolution by scanning the waveguide antenna's tip over the surface of the generator bars in a near-field measurement setup. Employing a frequency-modulated continuous wave technique, we obtain depth-resolved, volumetric terahertz images of the objects under test. We discuss here the implementation and performance of the implemented measurement system for terahertz NDT inspection. keywords: terahertz, non-destructive testing, dielectric waveguides, frequency-modulated continuous wave, millimeter waves, power generators

Modern radar sensors are gaining more and more relevance for several industrial measurement applications. To achieve the required range resolution and measurement accuracy, the use of higher frequencies beyond 100 GHz is beneficiary. A commonly used signal generation concept in fully integrated radar transceivers is to use a fundamental oscillator with subsequent frequency multiplication. Depending on the overall system concept, this type of signal generation suffers from a fundamental feed-through signal which generates false targets in frequency modulated continuous wave operation. Additionally, those unwanted signal components radiated by the sensors might be problematic for legal conformity or electromagnetic (EM) interference compliance. This paper presents a novel concept for frequency filtering dielectric lens antennas, to suppress unwanted signal components at harmonic frequencies based on interference filtering effects. Besides the EM simulations to theoretically prove this concept, multiple prototypes of filtering lens antennas were fabricated by conventional mechanical and additive manufacturing. Using a self-developed, ultra-compact radar sensor, measurements were taken to compare the lens antenna prototypes in terms of filtering performance and how the material characteristics affect the filtering performance. Within these measurements, the successful suppression of false targets caused by fundamental feed-through signals is demonstrated.

A five-slot hexagonal shape chipless RFID tag is designed, simulated, and manufactured on FR4 substrate. The designed tag's copper geometry was replicated on a wide range of dielectric substrate to quantify the impact on resonance quality factor (RQF) and resonating frequencies. The tag's performance was assessed in three configurations. First, a hexagonal shape tag's radar cross section (RCS) was studied over different dielectric substrates. The various dielectric substrate effects were investigated over the maximum read range, resonant frequencies and RQF. In the second evaluation, the physical geometry of the tag was adjusted to achieve the spectral signatures in 2–7 GHz frequency band with high RQF. In step three, the optimized tag geometry was manufactured on FR4, Roger Duroid 5880, and polyethylene naphthalate (PEN) substrates. Denford milling machine for PCB engraving and inkjet printing for silver nanoparticles deposition were used for tags manufacturing. During tag manufacturing, copper and silver were used as conducting materials for RCS backscattering. The tag RCS response was measured by vector network analyzer with bi-static antenna setup. The analysis of different dielectric substrate provides a pathway of designing a novel substrate by using various nanomaterials.

The design of a low-cost, flexible, miniaturized, and a high code density chipless radio-frequency identification (RFID) tag is presented as a solution for tracking the transportation of biomass fuel pellets. The performance of the tag is presented and demonstrates the applicability of the design for different material systems, while maintaining a compact size of 5.06 cm2. The tag consists of nested concentric hexagonal elements and a central spiral resonator suitable for ID encoding. The tag presented demonstrates code density of 3.6-bits/cm2, possesses angular stability up to 60°, and high radar cross section (RCS). The tag performance was also observed for tracking 5 kg of fly-ash biomass. Additionally, as the tag mass mostly consists of FR4, PET, or Taconic TLX-0 with a minute mass of either copper, gold, or silver, the tag can be easily combusted and disposed of during biomass combustion. The novel features of this tag are the combination of hexagonal and spiral shape slots for maximum space utilization thereby achieving high RCS signatures along with high code density. All these properties of the proposed chipless RFID tag provide a pioneering pathway for a real-time biomass tracking application.

This paper presents the design of two passive shaped-beam reflectarrays acting as passive intelligent reflecting surfaces (IRSs) to enhance 5G millimeter-wave coverage in the 27.2–28.2 GHz band. The reflectarray panels have been designed to generate a broadened and deflected beam in dual-linear polarization (horizontal and vertical). The reflectarray cell provides a robust performance under incidence angles of up to 50°, with more than 360° of phase variation range. Phase-only synthesis based on the generalized intersection approach has been applied to obtain the phase distribution on each reflectarray panel, so that their radiation patterns comply with the beamwidth and pointing requirements of the scenario under study. The two reflectarrays show a stable performance in the 27.2–28.2 GHz band in terms of gain, side-lobe level, and cross-polarization. The results confirm the potential of this technology to implement passive low-cost IRSs that will contribute to improve millimeter-wave coverage in 5G wireless networks.

Dielectric resonator antennas (DRAs) are developed antennas that are lightweight, wideband, small-sized and have high radiation efficiency. A DRA is an appropriate candidate for any radio communication including radar applications mainly because of its high efficiency and wideband performance. As the development of DRAs has been a continuous process for more than five decades the plethora of the same has become magnificent in all possible ways. Scientists have walked the technical path for more than centuries and tried to meet the various challenges in the most graceful ways. Reduction of loss, lightweight, and desired radiation patterns are some of the issues which are effectively met by DRAs. This paper presents a brief comprehensive review of the state of art techniques, giving an exhaustive idea of achieving broadband and multi-frequency operations in the areas of DRAs. The paper associates the references of the past and correlates with the current and future trends of research in DRAs that could be of immense help to the young upcoming researchers interested in this field.

In this paper, two high efficiency monolithic microwave integrated circuits (MMICs) are demonstrated using NANOTAM's in-house Ka-band fabrication technology. AlGaN/GaN HEMTs with 0.2 ${\rm \mu}$m gate lengths are characterized, and an output power density of 2.9 W/mm is achieved at 35 GHz. A three-stage driver amplifier MMIC is designed, which has a measured gain higher than 19.3 dB across the frequency band of 33–36 GHz. The driver amplifier exhibits 31.9 dB output power and 26.5% power-added efficiency (PAE) at 35 GHz using 20 V supply voltage with 30% duty cycle. Another two-stage MMIC is realized as a power amplifier with a total output gate periphery of 1.8 mm. The output power and PAE of the power amplifier are measured as 3.91 W and 26.3%, respectively, at 35 GHz using 20 V supply voltage with 30% duty cycle. The high efficiency MMICs presented in this paper exhibit the capabilities of NANOTAM's 0.2 $\rm\mu$m AlGaN/GaN on SiC technology.

Due to increasingly complex and automated manufacturing processes, the demands on the control parameters of these processes are also increasing. In many applications, such a parameter is the fill quantity, whose precise determination is of ever growing importance. This paper shows with which accuracy and precision an M-sequence ultra-wideband radar can determine levels in small metallic and non-metallic containers with contact-based and contactless measurements. First, the principle of level measurement using guided wave radar is explained and the measurement setup is described. Afterward, the measurement results are shown and discussed. The measurements show that the level can be measured with an accuracy of better than 0.5 mm. In addition, level fluctuations can be detected with a precision of 3 ${\rm \mu }$m. Based on the results of the guided wave radar, the possibilities of volumetric contactless measurement using an electrically small patch antenna are discussed. A particular challenge in contactless level measurement is the high number of multipath components, which strongly influence the accuracy. In addition, there are near-field effects when measuring close to the antenna. Exploiting these near-field effects, an additional method to accurately determine the full state of the container is investigated.

Extreme-high-speed communication exceeding 100 Gbps is one requirement for 6G. To satisfy extreme-high-speed-communication, one solution is to utilize terahertz bands above 100 GHz. To determine the new radio-interface technologies and service frequency bands for 6G, terahertz propagation characteristics above 100 GHz need to be understood. In this paper, we introduce our new radio-network topology for 6G and then show the frequency dependency of key propagation phenomena such as the characteristics of path loss in an urban environment, human blockage, and scattering from a rough building surface up to 150 GHz. Human blockage loss increases and the scattering is more diffused as the frequency increases. In the path-loss characteristics, it was found that path-loss frequency dependency is stronger than that given by conventional path-loss model because of scattering effects from a rough building surface.

A method is presented to optimize the combining network and the post-matching network of a Doherty power amplifier (DPA) for maximizing the bandwidth. For widely applicable results, RF power transistors are approximated in the large-signal regime using a simple analytical model with a few parameters. A definition of bandwidth of DPA is given, which involves gain and efficiency at full-power and 6 dB backoff. Different combining network topologies are compared in terms of this bandwidth definition. The element values are optimized using two factors, one to scale the combining node impedance and the other to scale the impedance seen by the transistors. For each optimized topology, explicit formulas are given resulting in the element values in terms of the optimized values and a few transistor parameters. The method presented also leads to a proper selection of the post-matching network.

This contribution describes the design and simulations of a multibeam 1.8 m parabolic reflectarray antenna for geostationary high throughput satellites (HTS) in Ka-band. The parabolic reflectarray generates two orthogonal circularly polarized beams per feed simultaneously at 19.7 and 29.5 GHz, by the variable rotation technique. The antenna is made of 62 654 reflectarray cells, which include two types of printed elements independently rotated and adjusted. The elements have been optimized one by one to ensure the required phase-shift at each frequency. A novel design approach has made it possible to promptly obtain an initial layout of every element with a very low computational cost. The simulated radiation patterns show that the parabolic reflectarray, illuminated by 27 dual-circularly polarized feeds, can generate 54 spot-beams in two orthogonal polarizations, with a beam spacing of 0.56° between adjacent beams. The design and simulation tools have been validated by a parabolic reflectarray scaled in a factor of 0.5, which has been manufactured and tested. The proposed reflectarray would allow to generate a complete multi-spot coverage from a geostationary HTS with only two parabolic reflectarrays, instead of four reflector antennas, also reducing the number of feeds by half, since every feed generates two beams.

Exposing the near field of an antenna to varying dielectric environment causes changes of the antenna input impedance and, thus, unwanted feed mismatch. Feeding such an antenna at different points, and selecting an appropriate feed for best match at a given scenario, may solve the problem. For the case of two scenarios of different dielectric environments and an antenna with two feed points, this work presents a passive power divider network, which keeps the antenna matched to the source in either scenario. Specific impedance transformations in the two branches of the divider network realize power transfer in a first scenario from the source to complex feed impedance at the first antenna feed, while in a second scenario, with now different antenna feed impedances, matched power transfer is from the source to the second antenna feed. Analytical formulae are derived for the design of the divider network. An experiment uses an example antenna with two feeds and a microstrip divider network, connected to a common 50 ohm port. Measurements are conducted with the antenna radiating, first, in air and, secondly, into butter. The measurements show antenna match at 1 GHz in either case and agree well with the analytical results.

A detailed dosimetry study of electromagnetic absorption and temperature rise under real scenarios is delivered when a mobile phone is used inside an elevator cabin. Numerically accurate human models of a 7th month pregnant woman and a 5-year-old female child are utilized as the exposed subjects. The female child acts as the phone user. The mobile phone is modeled in three talk positions (parallel, tilt, and cheek) operating at 1000 MHz and 1800 MHz. From the obtained numerical results for the specific absorption rate (SAR) and temperature rise induced by the mobile radiofrequency (RF) radiation, it is found that the child's RF exposure is significantly affected by the phone position and less affected by the relevant position of the human models. The exact opposite case applies for the pregnant woman model and its fetus. Almost all numerical investigations are carried out inside a metallic elevator cabin.