In this article, a new microstrip dual-narrowband bandpass filter employing parallel-coupled transmission lines and open stubs is presented, investigated, and fabricated. The proposed dual-narrowband bandpass filter is analyzed and its exact scattering parameters are calculated, simulated, and measured. So, calculated scattering parameters offer a deep inside view of the performance of the proposed filter. To analyze the proposed filter, the even- and odd-mode excitation are utilized. The input impedance under even- and odd-mode excitation are achieved by transmission line theory and inserted in the scattering parameter equations. Finally, the accurate scattering parameters are derived and compared with simulation results. Simulation results prove the theoretical results. Then, an optimized proposed filter is fabricated and matched with simulation results. The center frequency bands are 4.5 and 6.8 GHz. The optimized filter occupies 0.12 $ \times $ 0.096$\lambda _g^2$, which is small. Its fractional bandwidth of the first and second passband are 1.5 and 2.5%, respectively. Furthermore, wide and strong rejection levels in the stopbands are offered. The structure of the proposed filter provides many freedoms to design. There is an agreement between experimental and simulation results.

A class of balanced dual-band bandpass filters (BPFs) with planar transversal-signal-interference coupled-line sections is reported. In their building balanced dual-band BPF stage under differential-mode excitation, a second-order quasi-elliptic-type dual-band bandpass filtering transfer function is obtained. Specifically, from the transversal interaction among their two open-ended and virtually-short-ended half-wavelength coupled-line paths, sharp-rejection differential-mode dual passbands with several out-of-band transmission zeros at both sides are realized. To attain high common-mode suppression levels within the differential-mode passbands, two open-ended line segments are connected at the symmetry plane of the devised balanced dual-band BPF stage. Moreover, higher-order schemes based on in-series-cascaded multi-stage designs to further increase differential-mode selectivity and in-band common-mode rejection are illustrated. The operational principles and parametric-analysis design rules of the engineered transversal-coupled-line-based balanced dual-band BPF approach are detailed. Additionally, for a rigorous interpretation of their zero/pole characteristics, a digital-modeling framework is applied to them to connect RF balanced filters with their discrete-time versions. For practical-validation purposes, a microstrip prototype of two-stage/fourth-order balanced dual-band BPF is built and tested. It exhibits measured differential-mode dual passbands with center frequencies of 1.464 GHz and 2.294 GHz, 3-dB fractional bandwidths of 8.74% and 9.68%, and in-band common-mode rejection levels above 23.16 dB and 31.36 dB, respectively.

This paper studies the corona discharge power thresholds in microstrip bandpass filters (BPFs) and, in particular, is focused on a solution based on λ/2 cover-ended resonators to enhance their peak power handling capability (PPHC). First, a parametric analysis is carried out to evaluate the variation of the maximum electric field and the unloaded quality factor (Qu) as a function of the cover's geometrical dimensions (i.e. height, length, and width). Next, several microstrip BPFs centered at 1.6 GHz are designed, and their behaviors under moderate-to-high applied RF power signals are simulated to corroborate the previous study. A suitable number and size of covers are selected to enhance PPHC without barely degrading the filters’ electrical performance and, consequently, without hardly increasing the insertion losses. Finally, two third-order filters with covers and without covers (benchmark prototype) are manufactured, by way of illustration, and they are tested in the European High-Power RF Space Laboratory to validate the good performance of the proposed solution, where a PPHC enhancement of 3.1 dB at high pressures is achieved as compared to the benchmark prototype.

A miniature dual-band bandpass filter with interlocked stepped-impedance resonators (SIRs) is presented in this paper, which was designed for the student design competition held in European Microwave Week 2019. This bandpass filter is required to have two concurrent passbands, namely, the first passband at 900–1000 MHz and the second passband at 1427–1518 MHz bands, which cover six designated bands in sub-6 GHz range of fifth generation (5G) New Radio Access Technology. Three stopbands are required at 500–850, 1050–1350, and 1600–2000 MHz, respectively. To achieve the best figure of merit, an interlocked configuration of two SIRs is proposed. One advantage is that the impedance ratio of the inter-locked SIR can be controlled to have two passbands at the required frequencies. Second, the coupling section of the interlocked SIR gives three transmission zeros distributed to every stopbands such that the stopband suppression are dramatically enhanced. The measured results show that the passband insertion losses are 2.16 dB at the first passband and 1.33 dB at the second passband, and the return losses are greater than 10 dB. The stopband suppression at the transmission zeros are greater than 38 dB. The circuit is very compact as 41.40 × 19.96 mm2, equivalent to $0.25 \times 0.12\,\lambda _g^2$.

The design of a circular-shaped differential wideband band pass filter (BPF) is described. The proposed filter is compact and provides good common mode (CM) suppression. It consists of four ports with a circular-shaped differential mode (DM). The analysis of the filter has been carried out by bisecting it into identical two-port networks along the symmetry plane, resulting in a band stop or band pass response under CM or DM excitations, respectively. The length and width of the stubs can be tuned to obtain the desired pass band and stop band of the differential BPF. The proposed design is fabricated and measured. The results obtained using measurements are in close agreement with those obtained using simulations.

The design of mixed-technology quasi-reflectionless planar bandpass filters (BPFs), bandstop filters (BSFs), and multi-band filters is reported. The proposed quasi-reflectionless filter architectures comprise a main filtering section that determines the power transmission response (bandpass, bandstop, or multi-band type) of the overall circuit network and auxiliary sections that absorb the reflected radio-frequency (RF) signal energy. By loading the input and output ports of the main filtering section with auxiliary filtering sections that exhibit a complementary transfer function with regard to the main one, a symmetric quasi-reflectionless behavior can be obtained at both accesses of the overall filter. The operating principles of the proposed filter concept are shown through synthesized first-order BPF and BSF designs. Selectivity-increase techniques are also described. They are based on: (i) cascading in-series multiple first-order stages and (ii) increasing the order of the filtering sections. Moreover, the RF design of quasi-reflectionless multi-band BPFs and BSFs is discussed. A hybrid integration scheme in which microstrip-type and lumped-elements are effectively combined within the filter volume is investigated for size miniaturization purposes. For experimental validation purposes, two quasi-reflectionless BPF prototypes (one- and two-stage architectures) centered at 2 GHz and a second-order BSF prototype centered at 1 GHz were designed, manufactured, and measured.