A 3D-printed polarization-independent low-cost lightweight and flexible frequency selective surface based dual-band microwave absorber is presented in this paper. Two concentric square loops fabricated at different heights using 3D printing technology are responsible for exhibiting dual-band responses at 3.32 GHz (S-band) and 5.46 GHz (C-band) with more than 97% absorptivities. The corresponding full widths at half maximum bandwidths are observed as 230 MHz (3.21–3.44 GHz) and 450 MHz (5.27–5.72 GHz). The proposed topology is polarization-insensitive owing to the four-fold symmetry. The absorption phenomenon is explained with the analysis of current distributions at the surface and impedance curves at the frequencies of resonance. Further, the performance has been evaluated for both planar and curved surfaces with different angles of curvature, and the good agreement between the measured and simulated responses confirms the flexible behavior of the proposed structure.

In this paper, a single-layer band-stop frequency selective surface (FSS) by combination of Mike Kastle unit and square ring unit is proposed to achieve wide angular stable shielding. Owing to the rotational symmetry of the structure, the designed FSS is insensitive to polarization. By the combination design, the wide angular stability can be achieved as the incident angle increases from 0° to 85°, with only a maximum frequency deviation of 0.012 GHz. Meanwhile, the mechanism of the proposed FSS is investigated by the parametric analysis of equivalent circuit model. The prototype was manufactured and measured to verify the design and simulation analysis, and the measurement results were in good agreement with the simulation results.

Radar absorption structures made of an active frequency selective surfaces (AFSS) have enormous potential in the aviation, naval, and other industries. In this research paper, a systematic review (SR) is carried out in the field of the AFSS to bring uncertainties, obstacles, challenges, classifications, applications, and design issues that arrive in the development of the sub-6 GHz architecture. To bias the AFSS component, as per the signal requirements, a unique set of circuits (PIN diode) is required, with ON and OFF state and a transmission zone. The bandwidth of which is determined by the bias voltage supplied. It can behave as a complicated hybrid impedance structure by providing ON and OFF biasing voltage to a PIN diode embodied in an FSS structure. Higher manufacturing costs of AFSS components, more significant complexities involved, a large amount of power consumption, and reactive impedance losses are some common limitations faced while implementing and designing an AFSS. Many envisioned problems are corrected with the AFSS design, current or creative implementations, and processing parameters are investigated progressively. It implies that new AFSSs will be an alternative to regular FSSs in the future. This paper is based on Kitchenham’s three-phase review procedure and supplements it with results, views, and recommendations from other leading experts in the field.

By combining the technique of energy selective surface and frequency selective rasorber, an energy selective rasorber is proposed, which performs selective energy protection in the low communication frequency band (0.8–2 GHz) and wave-absorbing property in the high-frequency band (6–18 GHz). The design consists of two layers, of which the bottom one contains a lumped diode structure for energy selection function in the transmission band, while together with the top layer, they perform a wideband wave absorbing function. The simulated and measured results agree well with each other, and both show good absorption in 6–18 GHz and energy-selective property around 1.86 GHz. That is, when the incident power changes from −30 to 14 dBm, the reflection coefficient changes from below −22 dB to above −2 dB, while the transmission coefficient changes from above −3 dB to below −17 dB.

In this paper, a frequency selective surface (FSS) based shared-aperture antenna is designed for 5G/Wi-Fi applications. The 5G and Wi-Fi channel are separated to achieve different polarizations and simultaneous work. The proposed antenna is of ±45°-polarization in the 5G N79 band and vertical polarization in the Wi-Fi5.8 GHz band. The antenna is vertically stacked with the N79 band antenna located above the Wi-Fi band antenna. The N79 antenna is composed of FSS units with transmissive characteristics in the Wi-Fi band, and serves as an electromagnetically transparent surface to avoid blocking the Wi-Fi antenna. A prototype of our design is fabricated, assembled and tested, and measured results show that the prototype is able to cover the entire N79 band (4.1–5.2 GHz, 23.7%) and Wi-Fi5.8 GHz band (5.73–5.89 GHz, 2.8%). Measured average gain is 8.2 and 7.8 dBi in the N79 and Wi-Fi band, respectively, and radiation efficiency is over 86 and 80%. The proposed design exhibits separated channels, tri-polarizations, high gain and compact size, which is sufficient for regular 5G/Wi-Fi applications. The antenna also achieves a relatively wide and highly consistent signal coverage in the two bands, making it suitable for 5G/Wi-Fi multi-function communication and indoor 5G blind compensation.

A single-layer ultra-wideband (UWB) stop-band frequency selective surface (FSS) has several advantages in wireless systems, including a simple design, low debugging complexity, and an appropriate thickness. This study proposes a miniaturized UWB stop-band FSS design. The proposed FSS structure consists of a square-loop and metalized vias that are arranged on a single layer substrate; it has an excellent angle and polarization-independent characteristics. At an incident angle of 60°, the polarization response frequencies of the transverse electric and magnetic modes only shifted by 0.003 f0 and 0.007 f0, respectively. The equivalent circuit models of the square-loop and metallized vias structure are analysed and the accuracy of the calculation is evaluated by comparing the electromagnetic simulation. The 20 × 20 array constitutes an FSS reflector with a unit size of 4.2 mm × 4.2 mm (less than one-twentieth of the wavelength of 3 GHz), which realizes an UWB quasi-constant gain enhancement (in-band flatness is <0.5 dB). Finally, the simulation results were verified through sample processing and measurement; consistent results were obtained. The FSS miniaturization design method proposed in this study could be applied to the design of passband FSS (complementary structure), antennas and filters, among other applications.