A novel reconfigurable circular microstrip G-slotted antenna having a circularly defected ground structure (DGS) capable of switching its resonance frequency for several microwave applications is presented in this paper. Reconfigurability of the proposed G-slot antenna is obtained by incorporating three PIN diodes. One diode is embedded in the patch and two diodes are integrated into the DGS structure at appropriate places in the slot to achieve four different wireless applications such as aeronautical radio navigation (4.3 GHz with gain 3.6 dB), satellite communication (3.78 GHz with gain 3.7 dB), mobile communication (4.55 GHz with gain 4.0 dB), and WiMAX (3.35 GHz with gain 3.3 dB). These four bands are achieved depending on the different biasing conditions of the three PIN switches used. Antenna performance has been analyzed in ANSYS Electronics Desktop 2018.2 software. The equivalent circuit component of the switching element (PIN diode) has been considered and designed during the simulation. The creative structure lies in the way that it exhibits higher gain with compact size than the previously reported similar antenna. A prototype of the proposed patch antenna has been fabricated on a Roger substrate and its testing and measurement have been performed to demonstrate its desirable characteristics and features.

Future smart reconfigurable antennas (RAs) (Haupt R-L and Lanagan M (2013) Reconfigurable antennas. IEEE Antennas and Propagation Magazine 55, 49–61) will likely be fully multipurpose and controlled by software and equipped with machine learning skills that can discern and respond to alterations in the radio frequency environment. Cognitive radio utilizations will be accomplished using a new generation of antenna technology and communication protocols. The effective use of frequencies and the use of polarization diversity and radiation pattern reconfigurability to send data over existing congested frequencies will be major advantages for such applications. The usage of antennas that can be reconfigured in multiple-input multiple-output (MIMO) channels will enhance channel capacity while simultaneously improving channel efficiency and lowering costs (Christodoulou C-G, Tawk Y, Lane S-A and Erwin S-R (2012) Reconfigurable antennas for wireless and space applications. Proceedings of the IEEE 100, 2250–2261). There are a lot of antennas used both at the transmitter and at the receiver front end in a MIMO system. The benefit of employing such arrangements is that different types of information can be conveyed at a similar time, boosting the spectral efficiency of communication in a multipath situation. The coding rate, modulation level, and transmission signaling method of a MIMO system can all be changed in response to changing channel circumstances and user needs. In a MIMO context, polarization reconfigurable/frequency-reconfigurable/radiation pattern RA increase the degree of freedom and enhancing the system’s performance. The usage of such antennas greatly enhances capacity by enabling a choice of various polarization configurations and pattern diversity. Antenna arrays that can be reconfigured are also an appealing MIMO system solution that needs to retain robust communication channels, particularly in portable gadgets where the area is limited.

This research article represents the design of a simple, smaller, and novel frequency reconfigurable patch antenna for 5G communication using PIN diodes. This antenna operates in both mid-5G and high-5G bands. The antenna is intended to operate in eight distinct modes with three PIN diodes in 5G wireless communication covering 27.46–50 GHz of high-5G band (range n257/n258/n260/n261/n262) and frequencies of the 3–6 GHz of mid-5G band (range n77/n78/n79/n46). The antenna has an overall size of 20 mm × 25 mm × 1.6 mm and is placed upon a low-cost FR4 substrate. A higher radiation efficiency from 75% to 98% is achieved in all the different modes. The resonant frequencies are around 3.46, 4.43, 5.83, 31.8, 35.5, and 46 GHz in different modes of operation. Different switching statuses have been carried out in this research work and their performances have also been illustrated in the form of surface current distribution in different resonant frequencies. The simulated and measured results are compared to highlight its proposed design operation.

A 1-bit reconfigurable intelligent metasurface-based antenna for 5G application is proposed. The proposed antenna based on artificial electromagnetic metamaterial has the advantages of easy processing and low cost. This meets the requirements of future communication network development. This antenna shows that the unit cell has a stable 180° phase difference between the ON and OFF states by loading a PIN diode at 6.425–7.125 GHz. A 10 × 10 array antenna is constructed by using 2 × 2 meta-atoms to reduce the complexity of the control network. This proposed antenna can achieve ±40° beam scanning with a gain tolerance of 3 dB and a maximum gain of 18.7 dBi. In addition, beamforming performance, such as multi-beams, is also achieved. These properties ensure that the proposed antenna has great potential in wireless communication systems and microwave imaging systems.

An innovative and simple method for attaining broadband frequency reconfigurable antenna structure is presented using low-cost materials and a compact design. The frequency reconfigurability is attained by the “OFF” and “ON” mechanisms of three PIN diodes. Many performance observations are carried out such as reflectance coefficient, bandwidth (BW), resonance frequency, electric field, feed position variation, and gain among different configurations. The suitability of the presented work for the different applications lies in the X frequency band. The resonating frequency for all switch OFF modes is achieved at 13.2 GHz and one switch ON mode at 10.7 GHz. The proposed design yields the frequency tunability behavior over the broadband of 2.5 GHz. The design yields the directivity of 5.58 dB, the minimum reflectance coefficient of −17.27 dB, and a total gain of 3.87 dB. This design offers an electric field of 46 558 v/m, a BW of 340 MHz, and a normalized directivity of 87° using low-cost substrates. The results of the presented design were also fabricated and related to simulated results. Performance observation of the proposed work with previously published research work is also included. The presented design provides the solution of the low-cost, compact, reconfigurable antennas, which can be used for next-generation communication systems.

This paper proposes a wide band and multiband frequency reconfigurable antenna that can operate in the UWB, GSM, GPS, 4G LTE, WLAN, and WiMAX bands. The antenna is made up of a trapezoidal-shaped monopole radiator, which was inspired by a rectangular monopole antenna. The ground plane is modified by embedding T and L-shaped slots to notch the desired operating frequency. The proposed antenna can switch to six different frequencies using RF PIN diodes, making it suitable for modern wireless applications. A multilayer frequency selective surface (FSS) reflector is presented to improve the gain of the proposed reconfigurable antenna. The low-profile design achieved a significant increase in gain while retaining the UWB antenna's excellent impedance bandwidth. Because of the use of the FSS reflector, the antenna's average peak gain has increased from 6 to 10.4 dBi. The proposed antenna has a wide switching capability, which validates its unique feasibility for high-speed multiple Internet of Things applications via a common embedded platform under various applications.

A frequency reconfigurable microstrip patch antenna with a combination of an asymmetric armed U-slot and a reversed L-slot etched on a rectangular base patch of 6 GHz resonant frequency designed on an FR4 substrate (ɛr = 4.4) is presented in this paper. Three RF PIN diodes are positioned at inimitable sites of these slots to achieve frequency reconfiguration. A DC bias circuitry, which includes DC blocking capacitors and RF blocking inductors, is integrated with the antenna structure for switching (ON/OFF) the PIN diodes. Six reconfigurable modes with resonant frequencies at 4.33, 4.63, 5.24, 5.87, 5.96, and 6.29 GHz is obtained with different ON-OFF combinations of these PIN diodes. These reconfigurable resonant frequencies cover two continuous bands from 4.21 to 5.43 GHz and 5.69 to 6.6 GHz and is considered to be useful for the applications like aeronautical radio navigation (4.3 GHz), sub-6-GHz 5G (4.4–5 GHz), WLAN (5.2 and 5.8 GHz) and Wi-Fi 6E (5.925–6.425 GHz). Measured gain of the antenna for all the modes varies between 5.86 dBi and 8.72 dBi.

This paper presents center frequency and bandwidth switchable substrate integrated waveguide filters loaded with PIN diodes. The diodes are added in the slot on the surface of the resonators to switch the resonant frequencies and the coupling coefficients. Although the introduction of the slot causes extra radiation loss, it is small and acceptable. The proposed center frequency switchable filter has four center frequency switchable states of 1.78, 1.82, 1.88, and 1.91 GHz, while the bandwidth only changes ±0.64%. The bandwidth switchable filter has two states with 3 dB bandwidths of 70 and 103 MHz at a center frequency of 2.08/2.09 GHz. The measured performance of the fabricated filters shows good agreement with the simulation.

In this paper, multiple-input–multiple output (MIMO) antenna with dual-band frequency reconfiguration is presented. The proposed antenna consists of two symmetrical pentagon radiating elements. These radiating elements support bands of 1.5 GHz (GPS) and 2.4 GHz (Wi-Fi) frequency. The two PIN diodes are appropriately located on slot line in order to control the current flowing through the radiator. All simulated results are compared and confirmed with measured results. The antenna has VSWR ⩽1.8 and isolation of −28 dB. The advantage of this antenna is that bandwidth is increased by switching of PIN diode in the range from 80 MHz up to maximum 300 MHz. These characteristics demonstrate that proposed antenna is an attractive solution for a multimode application such as GPS, Wi-Fi routers, vehicular communication, etc. where wideband is required.

In this paper, a frequency reconfigurable microstrip slot antenna for ultra-wideband applications with switchable band-notch functions is designed and manufactured. To generate a wide usable fractional bandwidth of 3 to over 13.6 GHz, square patch transforms to a fork-shaped patch, also two triangular-shaped strips have been added at above sections of rectangular slot on the ground plane. Band rejections are obtained by adding two inverted L-shaped strips in the fork-shaped patch and one L-shaped defected ground structure. Moreover, by implementation of two PIN diodes within the antenna structure, four switchable frequency responses are achieved. The designed antenna has simple structure and a small size of 20 × 20 × 0.8 mm3 while providing band rejection characteristics at WiMAX (Worldwide Interoperability for Microwave Access) and WLAN (Wireless Local Area Networks) systems.

This paper presents a simple reconfigurable bandpass filter switching from 2.4 to 5 GHz based on PIN diodes. The proposed filter is intended to add frequency-tunability to antenna systems used in cognitive radio applications. It consists of a bent connecting stub with two open-circuited quarter-wave stubs grounded via PIN diodes. By controlling the didoes states, the electrical length of the stubs can be switched from quarter-wave to half-wave and vice versa, so as to tune the filter center frequency. The proposed design approach consists of ensuring communication at 2.4 GHz while blocking the 5 GHz band in the ON state, whereas in the OFF state, the filter is intended to reject the 2.4 GHz band and passing the 5 GHz band. A prototype of the proposed filter is fabricated and measured to validate the proposed concept. Both simulated and measured results show a two-state filter with a wide tuning range from 2.4 to 5 GHz and a good stopband rejection level better than 40 dB. Moreover, a flat group delay of about 0.55–0.7 ns is achieved within the operating bandwidth in both states. The proposed filter is able to achieve simultaneous bandwidth and frequency control, showing an important tool to meet modern system requirements.

In this manuscript, serial-shunt of square ring resonators with step-impedance open circuited stub resonators to produce a new on-off switchable bandpass to bandstop response in the same ultra-wideband microstrip filter structure is proposed. The closed ring of series-shunt square ring resonators with a combine stubs are introduced to excite the bandpass response while bandstop characteristic excited when gaps are embedded in the corners of the square ring resonators. The main advantage of this microstrip filter is its capability to switch from bandpass-to-bandstop operation using open-short gap, respectively. A microwave simulator is utilized to show the switchable case by replacing Skyworks radio frequency diodes (RF-PIN) instead of those gaps. The entire filter models have been simulated using the computer simulation technology (CST) Microwave Studio. The computed results for the proposed filters were compared with the measured results of the both prototype structures (bandpass- and bandstop-filter). The codes also showed good agreement between them. Other advantages include being small in size, and low in effective cost.

In this paper, a new antenna has been proposed with dimensions of 28 × 28 × 0.8 mm3 and the ability of operating in ultra-wideband (UWB) frequency and switching three notched bands. In the structure, to achieve the removal of characteristic of three frequency bands, a rectangular patch with an H-shaped slot on its surface and two C-shaped arms on its sides have been used. In addition, the designed antennas have the ability of operating in five different modes. To achieve the performance of reconfiguring, three pin diodes are used on the slots of rectangular patch and those two C-shaped arms. Also, with the defect ground structure and creating two rectangular slots and two L-shaped slots on the ground plane we make the excite of additional resonances and thus increase antenna bandwidth. Simulation and measurement results show that the designed antenna is able to cover the range of frequencies 3–12 GHz and a controllable frequency band rejection in the three frequency bands 3.2–3.75 GHz (WiMAX), 5.05–5.9 GHz (WLAN), and 8–8.45 GHz (ITU). The proposed antenna decreases the interference of the mentioned wireless systems with the UWB frequency.

A low specific absorption rate (SAR) reconfigurable multiband coplanar waveguide fed planar inverted-F antenna (PIFA) is presented in this paper. Different numbers of meander-turn-shaped slots are etched on the PIFA radiating plate to excite new resonant frequencies. Extra resonant frequencies are created by increasing the number of meander-turn-shaped slots for different wireless communication applications. A new independent resonant frequency is created by etching a coupled slot within the ground plane for the upper WLAN. A PIN diode switch is used to reconfigure the fundamental resonant frequency from the LTE band 11 to band 8 with a total of 63% size reduction compared with the original PIFA size. Furthermore, the SAR in the human head is investigated using the Hugo voxel model in CST Microwave Studio. The volume of the antenna is 22 × 30 mm2 over a 35 × 50 mm2 ground plane, which is suitable for handheld devices.