Ultrafast laser pulses provide unique tools to manipulate magnetization dynamics at femtosecond timescales, where the interaction of the electric field usually dominates over the magnetic field. Recent proposals using structured laser beams have demonstrated the possibility to produce regions where intense oscillating magnetic fields are isolated from the electric field. In these conditions, we show that technologically feasible tesla-scale circularly polarized high-frequency magnetic fields induce purely precessional nonlinear magnetization dynamics. This fundamental result not only opens an avenue in the study of laser-induced ultrafast magnetization dynamics, but also sustains technological implications as a route to promote all-optical non-thermal magnetization dynamics both at shorter timescales – towards the sub-femtosecond regime – and at THz frequencies.

The recent achievement of fusion ignition with laser-driven technologies at the National Ignition Facility sets a historic accomplishment in fusion energy research. This accomplishment paves the way for using laser inertial fusion as a viable approach for future energy production. Europe has a unique opportunity to empower research in this field internationally, and the scientific community is eager to engage in this journey. We propose establishing a European programme on inertial-fusion energy with the mission to demonstrate laser-driven ignition in the direct-drive scheme and to develop pathway technologies for the commercial fusion reactor. The proposed roadmap is based on four complementary axes: (i) the physics of laser–plasma interaction and burning plasmas; (ii) high-energy high repetition rate laser technology; (iii) fusion reactor technology and materials; and (iv) reinforcement of the laser fusion community by international education and training programmes. We foresee collaboration with universities, research centres and industry and establishing joint activities with the private sector involved in laser fusion. This project aims to stimulate a broad range of high-profile industrial developments in laser, plasma and radiation technologies along with the expected high-level socio-economic impact.

Nonlinear compression has become an obligatory technique along with the development of ultrafast lasers in generating ultrashort pulses with narrow pulse widths and high peak power. In particular, techniques of nonlinear compression have experienced a rapid progress as ytterbium (Yb)-doped lasers with pulse widths in the range from hundreds of femtoseconds to a few picoseconds have become mainstream laser tools for both scientific and industrial applications. Here, we report a simple and stable nonlinear pulse compression technique with high efficiency through cascaded filamentation in air followed by dispersion compensation. Pulses at a center wavelength of 1040 nm with millijoule pulse energy and 160 fs pulse width from a high-power Yb:CaAlGdO4 regenerative amplifier are compressed to 32 fs, with only 2.4% loss from the filamentation process. The compressed pulse has a stable output power with a root-mean-square variation of 0.2% over 1 hour.

The discharged capillary plasma channel has been extensively studied as a high-gradient particle acceleration and transmission medium. A novel measurement method of plasma channel density profiles has been employed, where the role of plasma channels guiding the advantages of lasers has shown strong appeal. Here, we have studied the high-order transverse plasma density profile distribution using a channel-guided laser, and made detailed measurements of its evolution under various parameters. The paraxial wave equation in a plasma channel with high-order density profile components is analyzed, and the approximate propagation process based on the Gaussian profile laser is obtained on this basis, which agrees well with the simulation under phase conditions. In the experiments, by measuring the integrated transverse laser intensities at the outlet of the channels, the radial quartic density profiles of the plasma channels have been obtained. By precisely synchronizing the detection laser pulses and the plasma channels at various moments, the reconstructed density profile shows an evolution from the radial quartic profile to the quasi-parabolic profile, and the high-order component is indicated as an exponential decline tendency over time. Factors affecting the evolution rate were investigated by varying the incentive source and capillary parameters. It can be found that the discharge voltages and currents are positive factors quickening the evolution, while the electron-ion heating, capillary radii and pressures are negative ones. One plausible explanation is that quartic profile contributions may be linked to plasma heating. This work helps one to understand the mechanisms of the formation, the evolutions of the guiding channel electron-density profiles and their dependences on the external controllable parameters. It provides support and reflection for physical research on discharged capillary plasma and optimizing plasma channels in various applications.

The spatial distribution of beams with orbital angular momentum in the far field is known to be extremely sensitive to angular aberrations, such as astigmatism, coma and trefoil. This poses a challenge for conventional beam optimization strategies when a homogeneous ring intensity is required for an application. We developed a novel approach for estimating the Zernike coefficients of low-order angular aberrations in the near field based solely on the analysis of the ring deformations in the far field. A fast, iterative reconstruction of the focal ring recreates the deformations and provides insight into the wavefront deformations in the near field without relying on conventional phase retrieval approaches. The output of our algorithm can be used to optimize the focal ring, as demonstrated experimentally at the 100 TW beamline at the Extreme Light Infrastructure - Nuclear Physics facility.

Diode-pumped rare gas lasers are potential candidates for high-energy and high-beam quality laser systems. Currently, most investigations are focused on metastable Ar lasers. The Kr system has the unique advantages of higher quantum efficiency and lower discharge requirements for comparison. In this paper, a diode-pumped metastable Kr laser was demonstrated for the first time. Using a repetitively pulsed discharge at a Kr/He pressure of up to approximately 1500 Torr, metastable Kr atoms of more than 1013 cm–3 were generated. Under diode pumping, the laser realized a dual-wavelength output with an average output power of approximately 100 mW and an optical conversion efficiency of approximately 10% with respect to the absorbed pump power. A kinetics study involving population distribution and evolution was conducted to analyze the laser performance.

In this work, we experimentally investigate the dependence of the stimulated Raman scattering (SRS) effect on the seed linewidth of a high-power nanosecond superfluorescent fiber source (ns-SFS). The results reveal that the SRS in the ns-SFS amplifier is significantly influenced by the full width at half maximum (FWHM) of the ns-SFS seed, and there is an optimal FWHM linewidth of 2 nm to achieve the lowest SRS in our case. The first-order SRS power ratio increases rapidly when the seed’s linewidth deviates from the optimal FWHM linewidth. By power scaling the ns-SFS seed with the optimal FWHM linewidth, a narrowband all-fiberized ns-SFS amplifier is achieved with a maximum average power of 602 W, pulse energy of 24.1 mJ and corresponding peak power of 422.5 kW. This is the highest average power and pulse energy achieved for all-fiberized ns-SFS amplifiers to the best of our knowledge.

Multilayer dielectric gratings (MLDGs) are crucial for pulse compression in picosecond–petawatt laser systems. Bulged nodular defects, embedded in coating stacks during multilayer deposition, influence the lithographic process and performance of the final MLDG products. In this study, the integration of nanosecond laser conditioning (NLC) into different manufacturing stages of MLDGs was proposed for the first time on multilayer dielectric films (MLDFs) and final grating products to improve laser-induced damage performance. The results suggest that the remaining nodular ejection pits introduced by the two protocols exhibit a high nanosecond laser damage resistance, which remains stable when the irradiated laser fluence is more than twice the nanosecond-laser-induced damage threshold (nanosecond-LIDT) of the unconditioned MLDGs. Furthermore, the picosecond-LIDT of the nodular ejection pit conditioned on the MLDFs was approximately 40% higher than that of the nodular defects, and the loss of the grating structure surrounding the nodular defects was avoided. Therefore, NLC is an effective strategy for improving the laser damage resistance of MLDGs.

The production of broadband, terawatt terahertz (THz) pulses has been demonstrated by irradiating relativistic lasers on solid targets. However, the generation of extremely powerful, narrow-band and frequency-tunable THz pulses remains a challenge. Here, we present a novel approach for such THz pulses, in which a plasma wiggler is elaborated by a table-top laser and a near-critical density plasma. In such a wiggler, the laser-accelerated electrons emit THz radiations with a period closely related to the plasma thickness. The theoretical model and numerical simulations predict that a THz pulse with a laser–THz energy conversion of over 2.0%, an ultra-strong field exceeding 80 GV/m, a divergence angle of approximately 20° and a center frequency tunable from 4.4 to 1.5 THz can be generated from a laser of 430 mJ. Furthermore, we demonstrate that this method can work across a wide range of laser and plasma parameters, offering potential for future applications with extremely powerful THz pulses.

Supersonic gas jets generated via a conical nozzle are widely applied in the laser wakefield acceleration of electrons. The stability of the gas jet is critical to the electron injection and the reproducibility of the wakefield acceleration. Here we discussed the role of the stilling chamber in a modified converging–diverging nozzle to dissipate the turbulence and to stabilize the gas jets. By the fluid dynamics simulations and the Mach–Zehnder interferometer measurements, the instability originating from the nonlinear turbulence is studied and the mechanism to suppress the instability is proposed. Both the numerical and experimental results prove that the carefully designed nozzle with a stilling chamber is able to reduce the perturbation by more than 10% compared with a simple-conical nozzle.

With the increasing power of fiber lasers, single chirped and tilted fiber Bragg gratings (CTFBGs) cannot completely mitigate continuously enhanced system-excited stimulated Raman scattering (SRS). Although improving the loss rate of a single CTFBG or cascading multiple CTFBGs can provide better suppression of the stronger SRS, excessive insertion loss may cause significant attenuation of the output power. Confronting the challenge, we firstly present an SRS mitigation method based on a dual-structure fiber grating in this paper. The dual-structure fiber grating comprises a CTFBG and a fiber Bragg grating structure, which were designed and fabricated on a passive 25/400 double-clad fiber. To evaluate the performance of the grating, a 3 kW fiber master oscillator power amplifier laser is established. The experimental results demonstrate that the SRS mitigation rate of the grating is greater than 30 dB (99.9%), whereas the insertion loss is only approximately 3%, thus allowing for minimal deterioration of the output power. This solves the contradiction between high suppression rate and high insertion loss faced by CTFBGs, which in turn makes dual-structure fiber gratings particularly suitable for mitigating SRS in 3–5 kW high-power fiber lasers.

All space–time coupling effects arising in an asymmetric optical compressor consisting of two non-identical pairs of diffraction gratings are described analytically. In each pair, the gratings are identical and parallel to each other, whereas the distance between the gratings, the groove density and the angle of incidence are different in different pairs. It is shown that the compressor asymmetry does not affect the far-field fluence and on-axis focal intensity. The main distinctive feature of the asymmetric compressor is spatial noise lagging behind or overtaking the main pulse in proportion to the transverse wave vector. This results in a degraded contrast but reduces beam fluence fluctuations at the compressor output. Exact expressions are obtained for the spectrum of fluence fluctuations and fluence root mean square that depends only on one parameter characterizing compressor asymmetry. The efficiency of small-scale self-focusing suppression at subsequent pulse post-compression is estimated.