In this paper, a triple-band bandpass filter using a multi-mode half-mode substrate integrated waveguide (HMSIW) cavity is presented. In this design, back-to-back connected half-mode defected ground structure (DGS) is loaded into the HMSIW cavity, which generates the first passband. The first four modes of HMSIW cavity are TM110, TM120, TM310, and TM320. They have been used to generate second and third passbands. The slot line perturbation is used to shift the modes close to each other. Here, TM110 and TM120 constitute second passband, and TM310 and TM320 give third passband. Moreover, the notch band is designed using embedded open-circuited stub to improve the attenuation between the second and third passbands. The proposed filter is designed and fabricated on RT/Duroid 5880 substrate with a thickness of 0.508 mm. The measured results are in line with simulated ones for each of the passbands, and the center frequencies are 6.28, 13, and 19.12 GHz.

A compact reconfigurable filtering ultra-wideband (UWB) antenna with switchable band-notched functions is proposed. The basic structure of the proposed design is a filtering slot antenna with good band-edge selectivity using stepped impedance resonator feeding line. The reconfigurability is achieved by using two microstrip lines paralleling to the feeding line and two PIN diodes. The reconfigurable structure and bias circuit of the antenna are relatively simple and are not connected to the radiation structure, so they have little negative influence on the radiation characteristics of the antenna. Total four states could be achieved by using two PIN diodes to short the microstrip lines and ground. To verify the performance of the final design, multiple measured and simulated results in frequency and time domain are studied and analyzed. The measured results agreed very well with simulation. Compared with the traditional UWB antenna, the proposed antenna has advantages in size, filtering function in-band and out-of-band, and tunable states for multiple UWB applications.

In this paper, an ultra-wideband (UWB) band-pass filter (BPF) with a sharp notch band is presented. The UWB BPF consists of modified elliptical-ring and multi-mode stub-loaded resonator (MM-SLR). By adding the asymmetric tight coupled lines resonator via input/output (I/O) lines, it can be achieved UWB band-pass response. With adding two bends to the middle resonator, a notch band at 6.86 GHz is created, so that it can be controlled using the mathematical formulas (MF). In the meantime, the equivalent circuit of the middle resonator is obtained using L–C analysis. Measured results of fabricated filter have the advantage such as ultra-wide pass band (fl and fH of the defined UWB pass band are 3.776 and 10.42 GHz, which satisfy the requirements of FCC-specified UWB limits), compact size, low insertion loss <0.65 dB and the stop band of the proposed filter is from 11.1 to 16.32 GHz with attenuation of −39.8 to −42.14 dB, respectively. The proposed UWB filter is realized using the substrate with dielectric constant of 2.2 and substrate height of 0.787 mm. Experimental verification is provided and good agreement has been found between simulation and measurement results.

This paper presents a band-notched ultra-wideband bandpass filter by loading a short stub and an asymmetric step impedance stub in a uniform impedance resonator. The passband extends from 3.04 to 10.8 GHz frequency. The multimode resonator provides a sharp band edge with measured transmission zeros at 2.59 and 13 GHz. The later one is due to source load coupling. The passband insertion loss is within 1.5 dB. The embedded spiral resonator introduces a notch at 5.25 GHz with attenuation of 15 dB. The filter exhibits a wide stop band till 15 GHz. The in band and out of band performance obtained from full-wave electromagnetic simulation and measurement are in close agreement.

In this paper, a new way of obtaining a band rejection in a ultra wideband (UWB) filter using a uniplanar Electromagnetic bandgap (EBG) structure is reported. The EBG structure has a bandgap centered at 6.69 GHz which is almost 38% lower compared with the conventional uniplanar EBG of same dimensions. A one-dimensional EBG structure coupled with a microstrip line provides a narrow bandgap, which is used in obtaining a notch in the UWB filter. Single notch UWB filters with variations in the placement of EBG are fabricated producing a notch centered at 5.19 GHz (wireless local area network (WLAN)). A dual notch (5.16 and 8.24 GHz (satellite communication)) UWB filter is also fabricated with two different unit cell EBGs'. Switchable and tunable notch band UWB filters are proposed.

In this paper, the design, simulation, and fabrication of a novel printed rectangular slot antenna with a band-notched function suitable for 2.4 GHz wireless local area network (WLAN) and ultra-wideband (UWB) applications is presented and investigated. Two pairs of slits are introduced into the ground plane to realize band-notched function, by tuning the position, length, and width of which a suitable rejected frequency band can be obtained. To improve the impedance matching, a rectangular cut is also made in the ground plane so that the antenna can cover 2–12 GHz frequency range. According to the measured results, the proposed antenna has a large bandwidth totally satisfying the requirement of 2.4 GHz WLAN and UWB systems, while providing the required band-notch function from 5.1 to 5.9 GHz. The study of transfer function and time-domain characteristics also indicates the band-notched function of the antenna. The radiation patterns display nearly omni-directional performance and the antenna gain is stable except in the rejected frequency band (5.1–5.9 GHz). Moreover, group delays are within 1.5 ns except for the notch band. These features make it a promising candidate for UWB wireless applications. Details of this antenna are described, and the experimental results of the constructed prototype are given.