A radio frequency (RF) 3-bit digital power amplifier (DPA) is described in this paper. It consists of three RF amplifiers connected at their outputs with a transmission line (TL) network. The three amplifiers are designed for different output powers (POUT). The TL network allows them to load-pull one other to achieve eight different amplitude states by alternatively enabling and disabling the amplifiers via their gate bias. A prototype was designed in the National Instruments' Microwave Office (MWO) for 500 MHz with the aid of a genetic algorithm to optimize the TL network for all seven active (on-) states. The optimizer efficiencies goals were based on data derived from load-pull simulation. The POUT goals were based on a 1 Vrms step-size. In simulation, ≥50% efficiency was achieved at all on-states with 29.7 dBm peak POUT. A practical prototype based on the simulation achieved an efficiency of ≥40% over all seven on-states. A peak POUT of 28.9 dBm was achieved, with the lowest state at 22.4 dBm.

This paper reports on a record-low-phase noise D-band signal source with 5 dBm output power, and 1.3 GHz tuning range. The source is based on the unconventional combination of a fundamental frequency 23 GHz oscillator in 150 nm AlGaN/GaN HEMT technology followed by a 130 nm SiGe BiCMOS MMIC including a sixtupler and an amplifier. The amplifier operates in compression mode as power-limiting amplifier, to equalize the source output power so that it is nearly independent of the oscillator's gate and drain bias voltages used for tuning the frequency of the source. The choice of using a GaN HEMT oscillator is motivated by the need for a low oscillator noise floor, which recently has been demonstrated as a bottle-neck for data rates in wideband millimeter-wave communication systems. The phase noise performance of this signal source is −128 dBc/Hz at 10 MHz-offset. To the best of the authors’ knowledge, this result is the lowest reported phase noise of D-band signal source.

A high power laser system was used to drive the ignition of inertial confinement fusion (ICF), of which the high energy, the uniform focal spot, the accurate laser waveform, and the synchronization between the laser beams are key parameters. To accomplish this, global laser characteristics control should be assured, which was the main purpose of the injection laser system. In this paper, the key technological progress involved in the improvement of the performance of the injection laser of SG-II is reported, including frequency domain control, time domain control, near-field spatial shaping, pre-amplifier technology, and the optical parametric chirped pulse amplification pump source.

A type of $\unicode[STIX]{x1D706}/4$–$\unicode[STIX]{x1D706}/4$ ultra-broadband antireflective coating has been developed using modified low refractive silica and high refractive silica layers by a sol–gel dip coating method for amplifier blast shields of the Shen Guang II high power laser facility (SG-II facility). Deposition of the first layer (high refractive index silica) involves baking at $200\,^{\circ }\text{C}$ in the post-treatment step. The second layer (low refractive index, $n=1.20$) uses low refractive index silica sol modified by acid catalysis. Thermal baking at temperatures no less than $500\,^{\circ }\text{C}$ for 60 min offers chemical stability, ethanol scratch resistance, and resistance to washing with water. The average residual reflection of dual-side-coated fused silica glass was less than 1% in the spectral range from 450 to 950 nm. Transmission gain has been evaluated by taking into account angular light, and the results show that the transmission gain increases with increasing light incidence. Even at $60^{\circ }$, the transmission spectrum of the broadband antireflective coating effectively covered the main absorption peak of Nd:glass.

This paper considers capabilities and benefits of aircraft-sized radio/radar frequency anechoic chambers for Test and Evaluation (T&E) of Electronic Warfare (EW), radar and other electromagnetics aspects of air and ground platforms. There are few such chambers worldwide. Initially developed to reduce costs, timescales and risks associated with open-air range flight testing of EW systems, their utility has expanded to most areas of platforms’ electromagnetics’ T&E. A key feature is the ability to conduct T&E of nationally sensitive equipment and systems, fully installed on platforms, in absolute privacy. Chambers’ capabilities and uses are described, with emphasis on key infrastructure and instrumentation. Non-EW uses are identified and selected topics elaborated. Operation and maintenance are discussed, based on experiential knowledge from international use and the authors’ 30 years’ involvement with BAE Systems’ EW Test Facility. A view is provided of trends and challenges whose resolution could further increase chamber utility. National affordability challenges also suggest utility expansion to support continuing moves, from expensive and difficult to repeat flight test and operational evaluation trials, towards an affordability-driven optimal balance between modelling and simulation, and real-world testing of platforms.

In this study, we propose a design methodology for a switching-mode RF CMOS power amplifier with an output transformer. For a given supply voltage, output power, and target efficiency, the initial values of the transistor size, output inductance, and capacitance can be sequentially determined during the design of the power amplifier. The breakdown voltage of the power transistor is considered in the design methodology. To prove the feasibility of the proposed design methodology, we provide the design example of a 2.4-GHz switching-mode CMOS power amplifier with 180-nm RF CMOS technology. From the measured results, the feasibility of the proposed design methodology is proved.

Colour patches are complex traits, the components of which may evolve independently through a variety of mechanisms. Although usually treated as simple, two-dimensional characters and classified as either structural or pigmentary, in reality colour patches are complicated, three-dimensional structures that often contain multiple pigment types and structural features. The basic dermal chromatophore unit of fishes, reptiles and amphibians consists of three contiguous cell layers. Xanthophores and erythrophores in the outermost layer contain carotenoid and pteridine pigments that absorb short-wave light; iridophores in the middle layer contain crystalline platelets that reflect light back through the xanthophores; and melanophores in the basal layer contain melanins that absorb light across the spectrum. Changes in any one component of a chromatophore unit can drastically alter the reflectance spectrum produced, and for any given adaptive outcome (e.g. an increase in visibility), there may be multiple biochemical or cellular routes that evolution could take, allowing for divergent responses by different populations or species to similar selection regimes. All of the mechanisms of signal evolution that previously have been applied to single ornaments (including whole colour patches) could potentially be applied to the individual components of colour patches. To reach a complete understanding of colour patch evolution, however, it may be necessary to take an explicitly multi-trait approach. Here, we review multiple trait evolution theory and the basic mechanisms of colour production in fishes, reptiles and amphibians, and use a combination of computer simulations and empirical examples to show how multiple trait evolution theory can be applied to the components of single colour patches. This integrative perspective on animal colouration opens up a host of new questions and hypotheses. We offer specific, testable functional hypotheses for the most common pigmentary (carotenoid, pteridine and melanin) and structural components of vertebrate colour patches.

A radiofrequency gaseous detection device is proposed for use with instruments employing charged particle beams, such as electron microscopes and ion beam technologies, as well as for detection of ionizing radiations as in proportional counters. An alternating (oscillating) electromagnetic field in the radiofrequency range is applied in a gaseous environment of the instrument. Both the frequency and amplitude of oscillation are adjustable. The electron or ion beam interacts with a specimen and releases free electrons in the gas. Similarly, an ionizing radiation source releases free electrons in the gas. The free electrons are acted upon by the alternating electromagnetic field and undergo an oscillatory motion resulting in multiple collisions with the gas molecules, or atoms. At sufficiently low pressures, the oscillating electrons also collide with surrounding walls. These processes result in an amplified electron signal and an amplified photon signal in a controlled discharge. The amplified signals, which are proportional to the initial number of free electrons, are collected by suitable means for further processing and analysis.