Natural C14 measurements have been performed at the Dept. of Physics, National Taiwan University since 1965, using a cylindrical proportional counter of 1000 ml (Hsu et al., 1965). The proportional counter is operated with CO2 as the filling gas at a pressure of 1216 mm Hg at room temperature of 20°C. Working voltage is 4.7 Kv, with a plateau length of more than 700 v and a plateau slope of ca. 1% per 100 v. Background is reduced to 5.1 counts/min and the counting rate of the NBS oxalic acid standard is 9.4 counts/min at the normal counting pressure of 1216 mm Hg.

In 1979 when accelerator mass spectrometry was started in the Netherlands, Gove (1978) and Litherland (1980) demonstrated that a tandem accelerator is eminently suited for this work. Isotope ratios below 10−15 could be determined and applications were stimulated on numerous fields of research. 14C dating in particular would become an important application because smaller samples could be employed and more complex dating problems could be attacked. However, the 5% accuracy reached at that time had to be improved towards the 0.5% obtained with the conventional method of counting decays. Purser and Hanley (1978) pointed out that this high accuracy could be reached in facilities especially dedicated to dating. Rapid switching between measurements on different isotopes turned out to be crucial (Suter et al, 1981). We decided to proceed in two phases. In the first phase, the existing EN-tandem facility would be used as before and modified for the detection of 14C ions. From measurements with 14C ions from different samples, information would be obtained about the limitations of the existing facility. In the second phase, this information would be used to develop a facility in which accurate measurements of isotope ratios can be performed for elements throughout the periodic system. Conventional 14C dating will be extended in collaboration with the Isotope Physics Laboratory in Groningen. Also, applications with other elements will be studied. The improved facility is scheduled for operation in the spring of 1983.

Quantifying the marine radiocarbon reservoir effect, offsets (ΔR), and ΔR variability over time is critical to improving dating estimates of marine samples while also providing a proxy of water mass dynamics. In the northeastern Pacific, where no high-resolution time series of ΔR has yet been established, we sampled radiocarbon (14C) from exactly dated growth increments in a multicentennial chronology of the long-lived bivalve, Pacific geoduck (Paneopea generosa) at the Tree Nob site, coastal British Columbia, Canada. Samples were taken at approximately decadal time intervals from 1725 CE to 1920 CE and indicate average ΔR values of 256 ± 22 years (1σ) consistent with existing discrete estimates. Temporal variability in ΔR is small relative to analogous Atlantic records except for an unusually old-water event, 1802–1812. The correlation between ΔR and sea surface temperature (SST) reconstructed from geoduck increment width is weakly significant (r2 = .29, p = .03), indicating warm water is generally old, when the 1802–1812 interval is excluded. This interval contains the oldest (–2.1σ) anomaly, and that is coincident with the coldest (–2.7σ) anomalies of the temperature reconstruction. An additional 32 14C values spanning 1952–1980 were detrended using a northeastern Pacific bomb pulse curve. Significant positive correlations were identified between the detrended 14C data and annual El Niño Southern Oscillation (ENSO) and summer SST such that cooler conditions are associated with older water. Thus, 14C is generally relatively stable with weak, potentially inconsistent associations to climate variables, but capable of infrequent excursions as illustrated by the unusually cold, old-water 1802–1812 interval.

Microbial mats (kopara in Polynesian) that develop in shallow brackish to hypersaline ponds on the rims of atolls were investigated for their accumulation process and rate. Two sequences of ∼30-cm-deep kopara, composed of 7 and 5 layers distinguished by their colors and sedimentological facies were collected in 1996 from the Tetiaroa atoll, French Polynesia. The combination of radiocarbon activity measurements on both organic and carbonate constituents, reservoir effect estimation, and comparison with the Southern Hemisphere atmospheric bomb-peak 14C record allowed us to establish a fine chronology of the layer successions documenting the mode of formation, erosion, and restoration of these microbial mat deposits.

A summary of the chronology for the key paleontological and archaeological site of Volchia Griva in the southern part of the West Siberian Plain is presented. Currently, 42 reliable 14C values have been generated on animal bones (37 14C dates) and charcoal (5 14C dates). Three stratigraphic levels of animal bones are established. The 14C ages of the fossils are as follows: the upper level—ca. 10,620–12,520 BP; the middle level—ca. 13,700–17,800 BP; and the lower level—ca. 18,230–19,790 BP. The majority of animal fossils and artifacts are associated with the lower level. Based on the results obtained, we suggest that Upper Paleolithic people occupied the Volchia Griva site during the second part of the Last Glacial Maximum (LGM), ca. 18,200–19,800 BP, and perhaps occasionally afterwards. It is obvious that these humans were well adapted to the cold and dry climate of the LGM, as well as numerous other populations in Siberia south of 58°N. It is noteworthy that the youngest 14C values on woolly mammoth are of ca. 10,620–11,815 BP, and this makes the Volchia Griva one of the latest mammoth refugia in northern Eurasia outside of the Arctic.

The results presented in this list are mostly from our earlier years of operation, the most recent of which were measured in 1984. It is the second of a series of special lists being prepared hopefully to clear the backlog of unpublished dates of this laboratory. All samples are of archaeological origin from the United Kingdom; most have originated from “rescue” type excavations and all were sponsored by the Ancient Monuments Laboratory of the Historic Buildings and Monuments Commission.

The management of counting files, the calculation of radiocarbon age, and the creation and maintenance of databases for storage and retrieval of laboratory data are time-consuming and exacting tasks. These routine functions are essential to the successful operation of all 14C dating laboratories. However, since the number of 14C dating laboratories worldwide is rather limited, it is unlikely that a commercial software company will produce a program for use in 14C age calculation and associated data management. We have therefore developed Windows based software to meet some of these needs.

The extraction of dissolved carbonate species for age dating from a 100L water sample by the direct-precipitation method (DPM) and by the gas-evolution method (GEM) has been investigated. Stable carbon-isotope fractionation between initial and final carbon dioxide evolved was ca 11‰ by GEM and 1‰ by DPM. GEM will produce isotopically lighter carbon dioxide compared with DPM if carbonate recovery is low. Extraction efficiency of > 95% can be achieved by GEM in 3 hours using nitrogen gas at a sweeping rate of 2000cc per minute. DPM requires precipitates to settle overnight to assure > 95% recovery. GEM is little affected by a high concentration of sulfate ions, whereas DPM is greatly affected by sulfate resulting in less yield.

Corrections are made to Stuart Fiedel’s (2022) recent errors and misrepresentations related to the late Pleistocene sites of Monte Verde and Huaca Prieta and to South American Fishtail projectile points.

Preparation of bones for radiocarbon (14C) dating is still quite a challenge for researchers. The methods are being tested and improved, to increase reliability of dating results and to verify the previous ones. In this work, a set of gelatine samples, extracted from Cervus elaphus and Cervus canadensis bones from various sites in Europe and a set of human bones from archaeological sites in Poland were subjected to retreatment using ultrafiltration in Gliwice Radiocarbon Laboratory. The tested samples represent a wide range of ages, from older than 40,000 14C years BP to modern. The prepared material was subjected to the measurement of C/N atomic ratios and 14C dating using the accelerator mass spectrometry (AMS) technique. Also, the stable isotopes (δ13C and δ15N) values were determined. In a few cases ultrafiltration allows to improve gelatine quality for long-stored samples, by increasing the %C and %N as well as decreasing C/Nat ratios. Nevertheless, this effect was not observed for majority of the samples. Remeasurements of long-term stored samples give mostly the same 14C ages for ultrafiltered ones and for those without ultrafiltration.

A newly developed compact AMS, LEA (Low Energy Accelerator), is tested and compared with a state-of-the-art AMS system MICADAS (Mini Carbon Dating System), which has a precision performance of better than 1‰ for modern 14C. The main difference between these two systems is the acceleration voltage, which has been reduced from 200 kV with the MICADAS system to 50 kV with the LEA system. In order to execute the final performance tests, exactly same samples (2 sets consisting of 7 standards, 4 blanks, 26 wood samples) are measured on both systems successively. The results show that the LEA system is fully operational, and the performance is entirely comparable with that of the MICADAS system.

Although paleomagnetic secular variations (PSV) often corroborate radiocarbon (14C)-based lacustrine sediment chronologies, this is not the case at the high-altitude site Khar Nuur in the Mongolian Altai Mountains. Our results show that the inclination pattern resembles those from a regional reference record from Shireet Naiman Nuur and global geomagnetic field models very well, but with a constant offset of 730 ± 90 yr. Possible reservoir effects from terrestrial pre-aging and hardwater effects can be excluded as the cause of the ∼730-yr offset because the different dated compounds correspond very well to each other, and modern reservoir effects are negligible. Instead, the constant ∼730-yr offset in the PSV pattern is likely the result of a constant lock-in depth of 26 ± 2 cm below the sediment-water interface at Khar Nuur. This assumption is supported by comparison of paleoclimatological proxies from Shireet Naiman Nuur, where similarities are obvious for the 14C-based chronology of Khar Nuur without a ∼730-yr adjustment. Therefore, the previously published 14C-based chronology of Khar Nuur provides a reliable age control. Accepting the lock-in depth of 26 ± 2 cm, the good consistency in inclination between Khar Nuur and global geomagnetic field models highlights the reliability of the latter even in a paleomagnetically understudied area.

To obtain scientific data regarding the chronology of archaeological structures, lime mortar radiocarbon dating has often demonstrated to be a decisive method. However, knowing the specific chemical-mineralogical characteristics of mortars can help when preparing samples or interpreting results. Among other issues, the dating of magnesian mortars can be particularly difficult because of the combined slaking, setting and hardening reactions of the calcium and magnesium phases, typical of these mortars. The formation of numerous mineralogical phases depending on reaction conditions adds further complexity to the dating method, which deserves to be studied with further detail. During the project “Mortar technology and construction history at Müstair Monastery” the first experiments in this regard had yielded encouraging results. An additional 4 samples from buildings with controversial chronology, thought to belong approximately to the 9th, 12th, and 15th centuries, were selected, prepared and radiocarbon dated. The data obtained were discussed by integrating preliminary petrographic characterization analyses of the mortars with archaeological information and excavation records. The results opened up new questions about the chronology of the Monastery, clarified the dating of some buildings and provided a better understanding of the potential and limitations of dating dolomitic mortars coming from archaeological context.

In this study, we investigate the distribution of radiocarbon and uranium in the calcified opercula of Turbo sp. collected from Ryukyu region and Chiba, Japan, to explore the potential of U/Th dating using mollusks collected from the Japanese archipelago. We acquired high-resolution radiocarbon and uranium concentration measurements using single-stage accelerator mass spectrometry and laser ablation−inductively coupled plasma−mass spectrometry. Our results show that uranium in the opercula of modern Turbo sp. is unevenly distributed at concentrations 1000 times less than those in coral skeletons. Radiocarbon found in the calcified opercula samples record ambient seawater radiocarbon values as well as coral skeletons. Uranium in the calcified opercula of Holocene Turbo marmoratus were also unevenly distributed and concentrated within the opercula in a different manner than observed in modern samples, suggesting uranium exchange after death. Our results suggest variable uptake of uranium isotopes into mollusk shells and highlights the need for rigorous sample selection criteria when choosing mollusks species for U/Th dating around Japan.

The research aims to reconstruct the chronology of building the Southwest Church, Umm el-Jimal, Jordan by AMS radiocarbon dating organic inclusions uncovered from the mortars collected from the floor of the church, seat of the apse and the base of the north wall. It sheds light on the major aspects of mortar recipes at the time of their production. Samples were examined macroscopically with magnifying lenses and characterized using archaeometric techniques of optical microscopy and X-ray diffraction. The radiocarbon dates showed that 594–643 AD is the most probable age for flooring and plastering the church and 995–1154 AD is the earliest possible date for its final collapse. The preparatory layers of the church floor were laid on an older one, probably of a yard, and its north wall was raised on an older base, both most probably date to the late fifth–early sixth century AD. The production recipe of the mortars is made from a lime binder and inclusions mainly of organic (charcoal) and inorganic (quartz, grog, volcanics). The mortars have the same recipe regardless their bedding and jointing functions which remained unchanged during the building stages of church complex.

Vast burial fields, some with hundreds of burials, categorize the southern Levant’s Intermediate Bronze Age period (IBA). This phenomenon contrasts with a limited number of burials found from the preceding Early Bronze III period. This paper presents the first radiocarbon dating research of sampled bones from shaft tombs from five IBA burial sites across Israel: Yehud, Jebel Qaaqir, Sheikh-Danon, Hazorea, and Kefar-Veradim. Prescreening methods, including Fourier transform infrared analysis, were applied to identify best-preserved collagen in archaeological bones for radiocarbon dating. Overall, the measured date ranges cover the IBA timeline, supporting the observation that the IBA signature shaft tombs are a fundamental tradition of the IBA culture, at least in Israel. A single IBA shaft tomb at Jebel Qaaqir which contained remains of multiple humans, supplied different dates for various people, spanning over a few hundred years. These results suggest a tribal or family-oriented IBA community with a long-lasting tradition reflected in centuries of collective burial practices.

Generally, 14C is produced in all types of reactors, mainly through neutron-induced reactions with isotopes of carbon, nitrogen, and oxygen. These isotopes are present in the fuel, fuel cladding, coolant, moderator, and structural materials of the reactor. Irradiated graphite contains a range of activation products but, from the point of view of geological disposal, another radionuclide which has to be taken into account is tritium (3H or T), produced through the neutron induced reaction Li(n,α)T. In this study we have investigated the release of 14C and 3H into the solution phase from two intact samples of irradiated graphite which have been cut from the thermal column disc located near the VVR-S reactor core. To evaluate 14C and 3H long-term release in solution the graphite samples were submerged in a solution of 0.1 M of sodium hydroxide. The experimental results regarding the release of 14C and 3H from VVR-S irradiated graphite to liquid phase show that a major fraction of the total release occurs in the first months and a slower release on a long time scale. However, these results should be applied cautiously for long time prediction.

Recent progress in preparation/combustion of submilligram organic samples at our laboratories is presented. Routine methods had to be modified/refined to achieve acceptable and consistent procedural blanks for organic samples smaller than 1000 μg C. A description of the process leading to a modified combustion method for smaller organic samples is given in detail. In addition to analyzing different background materials, the influence of different chemical reagents on the overall radiocarbon background level was investigated, such as carbon contamination arising from copper oxide of different purities and from different suppliers. Using the modified combustion method, small amounts of background materials and known-age standard IAEA-C5 were individually combusted to CO2. Below 1000 μg C, organic background levels follow an inverse mass dependency when combusted with the modified method, increasing from 0.13 ± 0.05 pMC up to 1.20 ± 0.04 pMC for 80 μg C. Results for a given carbon mass were lower for combustion of etched Iceland spar calcite mineral, indicating that part of the observed background of bituminous coal was probably introduced by handling the material in atmosphere prior to combustion. Using the modified combustion method, the background-corrected activity of IAEA-C5 agreed to within 2 σ of the consensus value of 23.05 pMC down to a sample mass of 55 μg C.