Hostname: page-component-78c5997874-g7gxr Total loading time: 0 Render date: 2024-11-02T19:20:34.928Z Has data issue: false hasContentIssue false
  • English
  • Français

High Temperature Mechanical Behavior of SiCf/Ti–Al Composites

Published online by Cambridge University Press:  01 January 1992

H.Y. Chou ,
S.C. Yang ,
K.L. Wang ,
C.I. Chen  and
S.E. Hsu
H.Y. Chou
Affiliation:
Materials R&D Center, CSIST, P.O. Box 90008–8, Lungtan, Taiwan, R.O.C.
S.C. Yang
Affiliation:
Materials R&D Center, CSIST, P.O. Box 90008–8, Lungtan, Taiwan, R.O.C.
K.L. Wang
Affiliation:
Materials R&D Center, CSIST, P.O. Box 90008–8, Lungtan, Taiwan, R.O.C.
C.I. Chen
Affiliation:
Materials R&D Center, CSIST, P.O. Box 90008–8, Lungtan, Taiwan, R.O.C.
S.E. Hsu
Affiliation:
Materials R&D Center, CSIST, P.O. Box 90008–8, Lungtan, Taiwan, R.O.C.
Get access

Abstract

Titanium aluminide was reinforced by AVCO SCS–6 continuous SiC fibers in unidirectional or 0°/+45°/–45° direction to make SiCf/Ti–A1 composites through hot-pressing of Ti and A1 powder mixture. The toughness of the composites is greatly improved at room temperature. The typical tensile elongation is over 0.8%. The room temperature strength of the composite can be sustained up to about 700°C. The processes developed in this study have two merits: (1) Ti and A1 powders instead of Ti–A1 powder can be directly used as raw materials, and (2) the mechanical properties of composites can be tailored in a similar fashion as those of conventional composites.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 288: Symposium L – High-Temperature Ordered Intermetallic Alloys V , 1992 , 1161
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Sastry, S.M.L. and Lipsitt, H.A., in Titanium 80' edited by Kimura, H. and Izumi, O. (Warrendale, PA: The metallurgical Society, pp1231–1243 (1980).Google Scholar
2. Barinov, S.M., Konilova, Z.I., Krasulin, Yu.L., Lazarev, E.M., Nartova, T.T., and Sapozhnikova, L.V., Poroshkovaya Metallurgiya, No.12(300), 61 (1987).Google Scholar
3. Mard–Close, C.M. and Patridge, P.G., J. Mater. Sci., 25 4315 (1990).Google Scholar
4. Brindley, P.K. in High–Temperature Ordered Intermetallic Alloys ”: edited by Stoloff, N.S., Koch, C.C., Liu, C.T.,, and Izumi, O. ( Material Research Society symposia proceedings, Vol.81, pp419–424 (1987)).Google Scholar
5. Rawers, J.C., Wrzesinski, W.R., Roub, E.K., and Brown, R.R., Mater. Sci. & Tech., Vol.6, No.2, 187 (1990).Google Scholar
6. Hsu, S.E., Wu, H.D., Li, C.M., Chou, H.Y., and Wang, K.L. in Proceeding of International Symposium on Intermetallic Compounds edited by Izumi, Osamu, Tohoku university, JIM, pp979–983 (1991).Google Scholar
7. Martineau, P., Pailler, R., Lahaye, M., and Naslain, R., J. Mater. Sci., 19, 2749, (1984).Google Scholar