Hostname: page-component-586b7cd67f-2brh9 Total loading time: 0 Render date: 2024-11-28T08:36:38.696Z Has data issue: false hasContentIssue false
  • English
  • Français

Modeling Combined Thermal, Electrical, Optical and Mechanical Response for MEMS Spectroscopic Gas Sensor Based On Photonic Crystals

Published online by Cambridge University Press:  11 February 2011

Anton C. Greenwald ,
Martin U. Pralle ,
Mark P. McNeal ,
Nicholas Moelders ,
Irina Puscasu ,
James T. Daly  and
Edward A. Johnson
Anton C. Greenwald
Affiliation:
Ion Optics, Inc., Waltham, MA 02452, USA
Martin U. Pralle
Affiliation:
Ion Optics, Inc., Waltham, MA 02452, USA
Mark P. McNeal
Affiliation:
Ion Optics, Inc., Waltham, MA 02452, USA
Nicholas Moelders
Affiliation:
Ion Optics, Inc., Waltham, MA 02452, USA
Irina Puscasu
Affiliation:
Ion Optics, Inc., Waltham, MA 02452, USA
James T. Daly
Affiliation:
Ion Optics, Inc., Waltham, MA 02452, USA
Edward A. Johnson
Affiliation:
Ion Optics, Inc., Waltham, MA 02452, USA
Get access

Abstract

A new type of gas sensor was developed that combines the principles of bolometric infrared detectors with photonic crystals.1,2 This paper describes a quantitative model used to optimize the materials, geometry, and electrical properties of this suspended membrane MEMS device. Fundamentally the model is concerned with the thermal response of the device using temperature dependent thermal conductivity, specific heat, and electrical resistance to calculate conduction, convection, and radiation losses for a negative temperature coefficient of resistance material. Variations in the electrical drive circuit, dc and ac response, low and high frequency sinusoidal and random noise, along with an exacting calculation of expected signal were used to improve design. The model follows the time evolution of the system. We show how look-up tables with scaling (derived from exact, off-line finite element models for thermal conduction, spectral emission, etc.) provided sufficiently accurate estimates with rapid calculation to enable running the model on a standard PC type computer. The simulations matched the experimental results, accurately predicted the unstable operating regimes, and maximized the signal to noise ratio for the device.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 741: Symposium J – Nano- and Microelectromechanical Systems (NEMS and MEMS) and Molecular Machines , 2002 , J12.3
Copyright
Copyright © Materials Research Society 2003

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. US patent 6,376,856.Google Scholar
2. Moelders, N. et al, “Designing Thermally Uniform MEMS Hot Micro-Bolometers” MRS Symp. Proc. v. 729, paper U5.2 (2002).Google Scholar
3. Pralle, M. U. et al,“Photonic Crystal Enhanced Narrow-band Infrared Emitters”, Appl. Phys. Lett., v81, p4685(2002).Google Scholar
4. Greenwald, A.C. et al, “Narrow Band Emission From Lithographically Defined Photonic Bandgap Structures In Silicon: Matching Theory And Experiment”, MRS Symp. Proc. v637, E2.6, (2000).Google Scholar
5. Puscasu, I. et al, “Frequency Selective Surfaces Enable MEMS Gas Sensor” MRS Symp. Proc. v. 722, paper L3.4 (2002).Google Scholar
6. Pralle, M. U. et al, “Photonic crystals for narrow-band infrared emission,” SPIE proceedings vol 4574, (2002).Google Scholar